Question about 1999 Chevrolet Malibu

1 Answer

Break lights not working, but the third break light is working

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Give the fuses a good check if not you might have to check the wiring (assuming you have already made sure the bulbs are good of course)

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What will cause no break lights other then the third break light?


Try replacing the brake light switch under the brake pedal. If the other lights are working it is not the fuse. If this does not fix it then the problem is most likely a short in the brake light switch wires.

Jun 24, 2014 | 1997 Lincoln Town Car

2 Answers

No break lights ,tail lights on a 1999 suberban check the fuse and they are all good when i turn my lights on and put on the turn singal and press on the break they start blinking very fast when i thouch...


it sounds like a ground problem...sounds like the ground is trying to go through the bulbs to make connection....check all ground wires battery, engine and rear frame...

May 27, 2011 | 1999 GMC Suburban

2 Answers

Both break lights went out at the same time. The


the brake pedal has a switch near it with a plunger on it for the brake lights... replace it

Feb 25, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

2001 GMC Jimmy break lights not working but all


Check the brake light switch should be a orange wire with 12v then a white wire with 12v when the pedal is pressed.If htat cks good then ck the hazard switch by moving it up and down and wiggeling the knob with the brake pedal pressed if they start working then your multifunction switch is bad and needs to be replaced.

Feb 20, 2010 | 2001 GMC Jimmy

1 Answer

No brake lights


It is not the brake switch as the third light works. If the lights work when the hazard lights are on then it is the turn signal switch. If not then I would check the bulbs and then the relay and fuses.

Jun 21, 2009 | 1997 Oldsmobile Cutlass

1 Answer

Tail break lights don't work. Window break light does work however. Bulbs have been replaced.


Check the brake light fuse. The high mounted brake light (third brake light) is on a different circuit than the brake lights. Hope this helps.

May 23, 2009 | 1998 Mercury Mystique

1 Answer

Malfunctioning brake lights.


Most likely a short in your break line. You might also check the brake switch, but I would think if the break switch was going, it you wouldn't even have the third lite working...

Aug 01, 2008 | 1999 Nissan Altima

1 Answer

Break light problem


Do you know if the brake light bulbs are working? (are the bulbs good?). (the bulbs have two parts, one for brake lights the other for running lights)
If the third brake light bulb is working the brake lights should be with good light bulbs.

Jul 22, 2008 | 2005 Honda Accord

Not finding what you are looking for?
1999 Chevrolet Malibu Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...