Question about 1991 Volvo 240

1 Answer

91 volvo rear running lights not working..

My rear running lights are not working...all signals,brake and front lamps are fine..fuses intact.
I'm baffled...any help you can give would be apperciated..

cheers!
wil
Canada.

Posted by on

  • Anonymous Mar 03, 2009

    Marcel Thank You!!
    I Cannot seem to log in..
    Will certainly give that a go..(Never thought of that one )..
    and keep you posted.

    All the Best,Mate!!

    wil

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

Had the same prob..check the the trunk where the bulbs are in the light bezel there's these flat steel contacts where the bulb housing is making contact with - fiddle with those a bit and you'll find that they'll come on when you move em around a bit. They're made pretty badly.

Posted on Mar 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

08 Buick lucerne cxl. Third brake light works as well as front signal lights. No rear brake lights or turn signals. Tail lights and headlights and third brake lights works. Bulbs good. Help


Stop Lamps
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake is applied, the BCM will then apply battery voltage to the left and right stop/turn signal lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM applies battery voltage through the signal circuit to the transmission control module (TCM) and the engine control module (ECM) indicating that the brakes are applied.
Ground for the stop lamps is supplied as follows:
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps
• G301 provides ground for the CHMSL
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.
Battery voltage from the LT TRN/SIG and RT TRN/SIG fuses located in the rear fuse block is also used by the body control module (BCM) for stop lamp operation.

Turn Signal Lamps
Battery voltage supplied to the body control module (BCM) from the fuses listed below is used for turn signal and hazard lamp operation.
• LT TRN/SIG fuse for the left turn signals
• CTSY/RF TRN fuse for the right front turn signal
• RR TRN/SIG fuse for the right rear turn signal
When the turn signal switch is place in either the LEFT or RIGHT position, ground from G300 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) to cycle the appropriate turn signal indicator ON and OFF.
Ground for the turn signal lamps is supplied as follows:
• G104 provides ground for the left and right front turn signal lamps
• G402 provides ground for the left rear stop/tail/turn signal lamps
• G403 provides ground for the right rear stop/tail/turn signal lamps

Do you have a factory scan tool (tech2) ? Your best bet , take it to the dealer .

Sep 08, 2017 | Buick Cars & Trucks

1 Answer

Brake lights work but tail lights don't work 91 LSC


check and make sure you have the correct light bulb in the tail lamp fixture.

Oct 15, 2013 | Lincoln Cars & Trucks

1 Answer

Nissan Xterra Brake Light Fuse Location


It's 15A FUSE 39 in the fuse & fusible link box

Mar 25, 2017 | Nissan Xterra Cars & Trucks

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

How do I change a brake light bulb in a 1999 c70 volvo?


Welcome to FixYa.com
Brake Lamp Replacement

Location of the lights

Image

The illustration shows the locations of the lights on the RH side. The LH side is the same but

mirror-reversed.

The lights have the following functions:

- 1 +1 = Parking light Fail light

- 2 = Reversing light

- 3 = Fog light LH side only (LHD cars)

- 5 = Direction indicator

- 6 = Brake light

Image

Tail light changing bulbs

Ignition off.

Open the cover in front of the tail light

Undo the wing nut and take out the lamp holder.

Change the defective bulb.

Fit in reverse order.

Check that all bulbs lamps are intact and in working order.

Image

Replacement of tail light cluster

Note! If a new tail light is to be fitted, the sleeves must be ground down 1.5 mm.

Open the cover in front of the tail light Undo the panel partly in front of the tail light Unplug the

connector for the tail light Undo the four nuts securing the tail light see illustration.

Pull the tail light straight out. Fit in reverse order

Note! check the sealing and fit on reassembly.

Check that all bulbs lamps are intact and in working order.Thank you for Using FixYa.comKind Regards, LeeYour FixYa Expert and Master Technician

Jan 27, 2011 | 1999 Volvo C70

1 Answer

I have a 2002 pontiac aztek. My rear right signal/brake lamp does not work. When i signal left, the front and rear left lights flash normally. When i signal right, the front right light flashes normally...


as for the faster flashing thats as simple as a blown bulb, replace the bulb and see if that fixes the problem, it may fix the lot because the other symptoms you mention are a bad connection, if bulb is fine check the connection isnt loose or corroded over. if it is simply file it back to establish better connectivity,

Jun 22, 2010 | 2002 Pontiac Aztek

1 Answer

Fuse problems on hyundia lantra 1999


are the rear lights combined? ie sidelamp and brake lamp in one bulb .if so, there is a possibility that the bulb is not sitting correctly in the holder , causing both the side & brake lamp fuses to blow . if they are seperate bulbs you probably have ashort in the sidelamp system somewhere but the brakes could be a switch problem [easy check, find switch ,disconnect wires short across using wire or paperclip switch on ignition and check lights ] if they work the switch is the problem , [check fuse first] if they don't

Jan 02, 2009 | 1999 Hyundai Accent

5 Answers

Chevy s10 brake lights


If the problem is that the brake lights will not turn off, the problem is most likely the CHMSL relay. An easy check is to take the cover off the fuse block mounted on the driver's side fender well and swap the fog lamp relay with the CHMSL relay. If that fixes it, just get a new relay for the fog lamps and you're good to go. Note, my 2002 s10 does not have fog lamps, but it still had the relay populated in the fuse block.

Jul 25, 2008 | 2001 Chevrolet S-10

Not finding what you are looking for?
1991 Volvo 240 Logo

Related Topics:

285 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...