Question about 1996 Mercury Sable

2 Answers

Program keyless remote for 94 Grand Marquis

I have old and new remote. I have permanent entry code. I have ignition key. What do I do ?

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Mercury Master
  • 783 Answers

On this model you will have to open glove box and press the tabs on each side so that you can open it all the way open. You will see a 2 wire grey connector behind it.
Turn ignition switch to run postion then take a paper clip or something like that and momentarily short the 2 wires together.
The door locks should then cycle from lock to unlock.Remove the paper clip then press one of the buttons on each remote. When you press the button on the remote door locks should cycle again to confirm that it programed.Then when finished turn off the ignition switch and door locks should unlock to confirm you have exited programming mode.

Posted on Feb 20, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 70,387 Answers

. Turn ignition to RUN or ACC. (this is from the factory manual) 2. Momentarily jump pins in programming connector located behind glove box.
All doors will lock then unlock to confirm programming mode.

3. Press any button on first keyless remote. Door locks will cycle to confirm programming.
4. If programming a second keyless remote, press any button on second keyless remote.
Door locks will cycle to confirm programming.

5. Turn igniton to OFF. Locks will again cycle to indicate end of programming mode.

Posted on Feb 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 crown vic keyfob only works with ignition in run position .keyless entry and door locks work fine.even tried new keyfob.no change


The keyless entry system consists of the following components:
  • driver door module (DDM)
  • keyless entry transmitter
  • keyless entry keypad
The driver door module (DDM) receives inputs from the digital transmission range (TR) sensor, ignition switch, brake switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
  • Battery junction box (BJB) fuses:
    • circuit breaker 7 (20A)
  • Central junction box (CJB)
    • 4 (10A)
    • 6 (15A)
    • 8 (25A)
    • 13 (5A)
  • Keyless entry keypad switch
  • Power door lock actuator
  • Luggage compartment release switch
  • Luggage compartment release solenoid
  • Connectors or connections
  • Wiring harness
  • If fuse's good have checked for DTC'S - diagnostic trouble codes .
  • B1526 Keyless Entry Circuit Short to Ground DDM Go To Pinpoint Test E . B1553 Decklid Release Circuit Short to Battery DDM Go To Pinpoint Test B . B1751 Park/Neutral Switch Circuit Short to Battery DDM Go To Pinpoint Test K . B2425 Remote Keyless Entry Out of Synchronization DDM Go To Pinpoint Test L Need a professional grade scan tool to check fro these codes . Not a code reader for OBD2 codes .
  • The doors do not lock/unlock using the remote transmitter
  • Remote transmitter not programmed.
  • Remote transmitter.
  • DDM.
  • Go To Pinpoint Test F .

Did you program the new key fob ?

Remote Transmitter Programming NOTE: All remote transmitters are programmable and must be set at the same time.
  1. Turn the key from OFF to RUN four times within three seconds, ending in RUN. The locks will then lock and unlock, confirming program mode has been entered.
  1. Press any button on each remote transmitter to be programmed. The doors will lock and unlock to confirm that each remote transmitter has been programmed.
  1. If additonal remote transmitters are to be programmed, repeat Step 3 within 7.5 seconds or steps 2 and 3 if more than 7.5 seconds have elapsed.
  1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
  1. NOTE: Failure to wait at least 20 seconds will cause programming failures. Wait at least 20 seconds after turning the key to OFF or after the last remote transmitter has been programmed to activate a remote transmitter for testing or verification

Feb 19, 2017 | Cars & Trucks

1 Answer

What is the color code for replacing the light switch on a '94 Marquis with factory alarm and keyless entry?


Here you go. I think this may be what you are looking for. I hope this helps and good luck.

1994 Mercury Grand Marquis Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Yellow Ignition Switch Harness Starter White/Pink Ignition Switch Harness Ignition Red/Light Green Ignition Switch Harness Accessory Gray/Yellow Ignition Switch Harness Tach Gray/Orange EDIS Module Brake Switch Light Green Brake Switch Trunk Release Purple/Yellow Driver's Kick Panel Trunk Pin Brown/White (-) Light in Trunk Parking Lights Brown Light Switch Head Lamp Red/Yellow Light Switch Hood Pin n/a Factory Disarm n/a Door Trigger Black/Light Blue Driver's Kick Panel Door Lock Pink/Yellow Behind Glove Compartment w/Keyless w/o Keyless (-) Door Unlock Pink/Light Green W/o Keyless Reverse Polarity Horn Wire Yellow/Light Green (-) Steering Column Windows Up LF=Yellow, RF=White/Yellow, Windows Down LF=White/BlackRF=Tan/Light Blue

Mar 26, 2011 | 1994 Mercury Grand Marquis

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

1 Answer

My door lock remote will not function and new


have you tried to press/hold lock button for 30 secs.
the code changes everytime you use the remote so that only your remote unlocks your car,not everybody elses.the key has a code inbuilt into it so the car will only start with your key...(this is dealer programmable)

Apr 05, 2010 | 2000 Mercury Grand Marquis

1 Answer

How to change the keypad code on a 2001 mercury grand marquis


look for the permanent code on the plastic card in the owner manual packet. Or, pay dealer to extract code from computer.

Keyless Entry Keypad Code Programming NOTE: The system only allows one code to be programmed.
  1. Enter the permanent factory keyless entry keypad code.
  1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds after activation will erase the stored customer code . The door locks will lock, then unlock, confirming the code is erased. The existing code will not need to be erased to program new a code.
  1. Within five seconds, enter the new five-digit keyless entry keypad code. The door locks will lock and unlock to confirm the new code is programmed.

Feb 08, 2010 | 2001 Mercury Grand Marquis

1 Answer

How do you program the remotes for keyless entry with a 200 pontiac grand am?


Transmitter Programming
No Tools Required
In the event that a transmitter is lost, program the old and the new transmitters into the memory of the remote control door lock receiver. Up to 4 transmitters may be programmed.


Important
Once the keyless entry receiver enters the programming/diagnostic mode, the programming of the first transmitter erases all previous transmitter programming information. You must then program all of the transmitters.

Program only 1 vehicle remote control door lock receiver at a time. If you program multiple receivers simultaneously, the same transmitter could possibly be programmed to more than 1 remote control door lock receiver.


Perform the following steps:

Sit in the vehicle driver's seat.
Remove the ignition key from the ignition lock cylinder.
Close all of the vehicle's doors.
Remove the MALL PGM fuse from the fuse panel. Refer to Electronic Diagnosis in Body and Chassis.
Turn the ignition lock cylinder to the ACC position.
Turn the ignition lock cylinder OFF, then back to ACC within 1 second.
Open and then close any vehicle door. You will hear a chime when the remote control door lock receiver enters the programming/diagnostic mode. If you do not hear a chime, start again at step 1.

Important
After 7 seconds, you may hear a chime confirming successful synchronization. After approximately 14 seconds, you will hear a chime confirming successful programming.


Press and hold the transmitter LOCK and UNLOCK buttons simultaneously for 14 seconds.
Repeat step 8 in order to program each additional transmitter.
Remove the ignition key from the ignition lock cylinder.
Install the MALL PGM fuse back into the fuse panel. Refer to Electrical Diagnosis in Body and Chassis.
Validate that all the transmitters that were programmed operate properly. Refer to Keyless Entry System Operation

Oct 21, 2009 | 2000 Pontiac Grand Am GT

1 Answer

Keypad door lock does not work..?


it's in owner manual. But, first you have to enter your original code and it must work. then you press the 1 button and then enter a new 5 digit code, then press the 1 button again.

Keyless Entry Keypad To unlock the driver front door (20124) , and disarm the anti-theft alarm control (19A366) , (if equipped):
  • Enter the permanent factory code.
  • Enter the owner's alternate code.
To unlock the passenger door(s), press the 3/4 button within five seconds of unlocking the driver door or luggage compartment. To unlock the luggage compartment door (40110), press the 5/6 button within five seconds of unlocking driver or passenger door(s). To turn on the courtesy lamps and light all illuminated components, lift either front door handle (22404) or press any button on the keyless entry keypad (14A626) . To lock all doors, press the 7/8 and 9/0 buttons at the same time with all doors closed. (It is not necessary to enter the key code first.) This will turn off courtesy lamps and arm anti-theft alarm control (if equipped). To program an alternate code:
  1. Enter the five digit permanent entry code into keyless entry keypad .
  1. Within five seconds of pressing last button of permanent code, press the 1/2 button within five seconds of pressing the last button of the permanent code.
  1. Enter any alternate five digit code within five seconds of pressing 1/2 button.
    • Enter a sixth digit as follows to indicate operator's memory seat setting to be set by alternate code:
      • 9/0 — no memory recall
      • 1/2 — memory seat position 1
      • 3/4 — memory seat position 2
      • 5/6 — memory seat position 3
    • After successful programming, the doors will signal by locking and then unlocking.
---------------------------------------------
  • Keyless Entry Keypad Does Not Work Properly
  • Circuit.
  • Keyless entry keypad.
  • Electronic door lock control processor.

  • Open Fuses:
    • Town Car and Crown Victoria/Grand Marquis
    • Power Distribution Box (under hood)- K, 40A (Maxi)
    • Instrument Panel Fuse Panel - 17 (10A), 10 (20A), 8 (15A), 5 (15A) and 4 (10A)
  • Loose Connectors
  • Corroded Connectors
  • Oct 04, 2009 | 1995 Lincoln Town Car

    1 Answer

    I need to program the key fob


    . Enter 5-digit permanent entry code into the keyless entry driver door keypad. 2. Within 5 seconds of pressing last button of code, press the 1/2 button. All doors will lock then
    unlock confirming you are in programming mode.

    3. Press any button on first Keyless Remote within 5 seconds of pressing the 1/2 button. Locks will
    cycle to indicate succesful programming.

    4. If you are programming more than one Keyless Remote (Including any exsiting remotes) Press
    any button on second keyless remote within 5 seconds of previous remote. Locks will cycle again
    to indicate succesfull programming. (If the keypad light goes out before all remotes are
    programmed the entire process must be repeated).

    5. Press the 7/8 and the 9/0 buttons simultaneously on the keypad to exit program mode.

    Jun 29, 2009 | 1997 Mercury Grand Marquis

    1 Answer

    Keypad reset. Now that I have the original keypad code, how do I change the code?


    your owner manual tells you. Why not use the original code?

    To change, here is 96 procedure, should be the same. please give good rating if this is what you want.

    Entry Code The system (permanent) entry code is located in three places:
    • on the owner's wallet code card (in glove compartment)
    • electronically accessible by requesting the remote anti-theft personality module KEYCODE PID on the New Generation Star (NGS) Tester
    • on the remote anti-theft personality module housing
    The remote anti-theft personality module is programmed at the factory with a five-digit entry code. A replacement remote anti-theft personality module includes replacement labels and a new owner's code card. To turn on the interior lamps and light all illuminated components:
    • press any button on the keyless entry keypad (14A626).
    To program a temporary access code:
    • Enter the permanent code on the keyless entry keypad.
    • Press button 1/2 within 5 seconds of last digit of permanent code. (This alerts system to accept temporary code.)
    • Enter alternate five-digit code. Do not exceed 5 seconds between entering digits or between pressing the 1/2 key and entering the first digit.

    Apr 08, 2009 | 1995 Ford Taurus

    2 Answers

    1999 lincoln con


    SECTION 501-14B: Keyless Entry/Computer Operated Locks 1999 Town Car Workshop Manual GENERAL PROCEDURES Programming —Keyless Entry Keypad Code
    1. Enter the permanent factory keyless entry keypad code.
    1. Press the 1/2 button within five seconds to activate the programming mode. Holding the 1/2 button for more than two seconds will erase all stored customer codes. The existing codes do not need to be erased to program new codes.
    1. Enter the new five-digit keyless entry keypad code.
    1. To associate the new code with personality positions 1, 2 or 3, press the 1/2 button within 5 seconds of entering the 5th digit of the new code for position 1 or 3/4 button for position 2 or 5/6 for position 3. The door locks will lock and unlock confirming the new code is programmed.
    1. If another code is to be programmed, begin entering the code within 5 seconds of the last button pressed.
    1. After all new keyless entry codes are programmed:
      • Press keyless entry keypad buttons 7/8 and 9/0 at the same time to exit the program mode.
      • Wait for 5 seconds; the driver door module (DDM) will exit the program mode automatically.
      • -------------------------------------------------------------
    Programming —Transmitter
    1. Cycle the ignition from OFF to RUN four times within three seconds. The locks will then lock and unlock, confirming program mode has been entered.
    1. NOTE: When the first keyless entry remote transmitter is programmed, all other keyless entry remote transmitters are erased.
      Press any button on the transmitter to be programmed.
    1. If additional keyless entry remote transmitters are to be programmed, repeat step 2 within 7.5 seconds.
    1. To exit program mode, turn the ignition to START or wait 7.5 seconds.
    --------------------------------------------------
    Programming —Remote Memory Activation NOTE: This procedure must be completed within 5 seconds.
    1. Press the SET button on the driver door panel.
    1. Press any button on the keyless entry remote transmitter to be associated with a memory setting.
    1. Press the 1 or 2 memory button on the driver door panel.
    -------------------------------------------------------------
    Programming —Autolock and Horn Chirp
    1. NOTE: This procedure must be completed within 30 seconds.
      Turn the ignition switch to RUN.
    1. Press the UNLOCK button three times.
    1. Turn the ignition switch to OFF.
    1. Press the UNLOCK button three times.
    1. Turn the ignition switch to RUN. The doors will lock and unlock to confirm entry into program mode.
    1. Press the UNLOCK button once to toggle the Autolock feature on or off, or twice to toggle the Horn Chirp function on or off. The horn will chirp to confirm toggling of the Autolock feature.
    1. Exit program mode by turning the ignition to OFF, START, or wait 7.5 seconds.
    ----------------------------------------------------------------------------------

    Apr 07, 2009 | 1999 Lincoln Town Car

    Not finding what you are looking for?
    1996 Mercury Sable Logo

    700 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Mercury Experts

    yadayada
    yadayada

    Level 3 Expert

    70387 Answers

    Ron Lankford

    Level 3 Expert

    5386 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22041 Answers

    Are you a Mercury Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...