Question about 2001 Daewoo Lanos

1 Answer

Replaceing the head what is the torck ft lbs and sequence

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Daewoo Master
  • 21,949 Answers

About 80lbs is about right ,start in middle and then work your way out doing one either side as you go .middle bolt top middle bolt bottom ,top left next too it then bottom right next to it and so on .

Posted on Aug 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need head bolt torque specs for a 1996 saturn sl


Quote:





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.





Originally Posted by norvelplagbao52

1993 saturn sl2 1.9 dohc cylinder head torque
specs and sequence
Cylinder head bolt
tightening procedure:
CYLINDER HEAD BOLT TIGHTENING SEQUENCE:

INTAKE
SIDE
8 4 1 5 9

7 3 2 6 10
EXHAUST SIDE

In sequence,
torque the cylinder head bolts. Torque: 30 Nm (22 ft-lbs).
In sequence,
torque all bolts. Torque: 50 Nm (37 ft-lbs)
In sequence, turn each bolt an
additional 90 degrees.

Sep 19, 2013 | 1996 Saturn SL

Tip

Nissan altima 2.4 L torque specs.


Torque sequence ---------------- | 9 3 1 6 8 | | 7 5 2 4 10 | ---------------- Step 1: Torque in sequence 22 Ft/Lbs Step 2: Torque in sequence 58 Ft/Lbs Step 3: Loosen all bolts completely Step 4: Retorque all bolts in sequence 22 Ft/Lbs Step 5: Retorque all bolts in sequence 54-61 Ft/Lbs recheck final torque in sequence *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque. 0900c15280265395.jpg

on Jul 08, 2010 | Nissan Altima Cars & Trucks

2 Answers

Dear expert What are the cylinder head bolt torque settings for the 4.0L MFI straight 6 engine? Regards Dave


Here are the specs and sequence:

0900c152800a9943.gif

Install the cylinder head and bolts. The threads of bolt No. 11 must be coated with Loctite® 592 sealant before installation. Tighten the bolts in 3 steps, using the correct sequence:

  1. Tighten all bolts to 22 ft. lbs. (30 Nm).
  2. Tighten all bolts to 45 ft. lbs. (61 Nm).
  3. Retighten all bolts to 45 ft. lbs. (61 Nm).
  4. Tighten bolts 1 through 10 in sequence to 110 ft. lbs. (150 Nm).
  5. Tighten bolt 11 to 100 ft. lbs. (136 Nm)
  6. Tighten bolts 12 through 14 to 110 ft. lbs. (150 Nm)

May 04, 2011 | 1996 Jeep Grand Cherokee

1 Answer

Can't find cylinder head torques!!! please advice....


Torque sequence: ----------------- there are two rows of fasteners and you need to start with the middle 2 fasteners first and then work your way toward the front and back in steps. Step 1: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 10 Ft/Lbs Step 2: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 20 Ft/Lbs Step 3: torque head bolts #1,2,3,4,5,6,7, & 9 in sequence to 29 Ft/Lbs Step 4: turn all head bolts in sequence an additional 90 degrees Step 5: turn all head bolts in sequence an additional 90-degrees recheck final torque in sequence. Fasteners are supposed to be replaced if they are removed since they are torque-to-yeild fasteners.

7 - 5 - 1 - 3 - 10
front
9 - 4 - 2 - 6 - 8

Apr 17, 2011 | 1997 Toyota Previa

2 Answers

What is the cylinder head torque specs?


The torque for the cylinder head bolts is 54 Ft Lbs. or 73 Nm

Note: they should be torqued in three steps (i.e. 20 Ft Lbs, 40 Ft Lbs, then the final 54 Ft Lbs) in the sequence shown in the picture.dttech_28.gif

Feb 26, 2011 | 1993 Geo Metro

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


    Cylinder heat bolt torque:
    Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
    Main bearing torque:
    Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
    Connecting rod torque:
    Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

    May 17, 2010 | 1997 Ford F150 Regular Cab

    1 Answer

    Head bolt tourqe settings on a toyota cressida


    Cylinder head bolt removal sequence


    Removal sequence: Front 3 7 11 13 10 6 2 1 5 9 14 12 8 4

    ***CAUTION*** The above sequence must be followed during removal as to avoid warpage of the cylinder head unit

    Reverse sequence to install, Step 1: Torque to 10 Ft/Lbs Step 2: Torque to 18 Ft/Lbs Step 3: Torque to 25 Ft/Lbs Step 4: Turn an additional 90 degrees Step 5: Turn an additional 90 degrees Step 6: Torque the 2 recessed 8mm bolts to 13 Ft/Lbs *** CAUTION *** engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper Torque

    Don't forget to rate this answer, Good Luck

    Apr 24, 2010 | 1992 Toyota Cressida

    2 Answers

    Head gasket torque specifications and sequense


    Please don't forget to rate. Thank you:

    Left side front cylinder head


    98e175a.gif
    Cylinder head bolt torque sequence—3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence—3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Mar 06, 2010 | 2001 Chevrolet Venture

    Not finding what you are looking for?
    2001 Daewoo Lanos Logo

    Related Topics:

    86 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daewoo Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Steve Hurc
    Steve Hurc

    Level 3 Expert

    450 Answers

    Are you a Daewoo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...