Question about 1998 Hyundai Elantra

1 Answer

Timing could someone please be able to tell me how to set up the timing on a hyundi lantra 1997 1.8L

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 366 Answers

Timing is electronnically ajusted by the computer

Posted on Feb 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My hyundi lantra wont drive i put the drive shaft in and it wont move would it be because there is no oil in the manaul transmission


I'm not a mechanic guru but be sure, if you have no oil in transmission, your system is definitively damaged.
Fill the oil but, I guess, it's too late, damage is done.
If still won't move, tow it to your repair service, probablbly you'll have to spend some good money repairing it.

Sep 21, 2015 | Hyundai Cars & Trucks

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

2 Answers

Torque wrench settings for 97 hyundai lantra 1.8


They use throw away bolts. One use only, so don't reuse your old ones. You will need new ones. The smaller bolts 1st torque setting 22Ft/Lbs and the larger 26ft/lbs, the 2nd torque setting 60 degrees both bolt sizes and the 60 degrees for the third.

May 20, 2009 | 1997 Hyundai Elantra

1 Answer

Can anybody tell me why elantra keeps popping up when i need a manual for a lantra 1600 is there a manual that matches this from another model


I found the best way is to take the idle pulley off first then with a little effort you can slide it over the cam pulley. Then reinstall the belt tensioner/ idler pulley and adjust. Do not over tension the belt .

Apr 17, 2009 | Hyundai Elantra Cars & Trucks

2 Answers

Hyundai Lantra gearbox problems


the lantra gearbox is a Mitsubishi unit and i think it does not have bands just clutches.

Mar 31, 2009 | Hyundai Motor 1996 Elantra

1 Answer

Hyundai Lantra 19999 Timing Mark


are you setting the timing belt or just setting the timing with a light ? if you are setting the timing it should be set at about 10 before top dead center or maybe would run a little better at 12 or so thanks jerry holler if you have more .

Feb 07, 2009 | 1996 Hyundai Sonata

1 Answer

Hyundai lantra


The baseline idle is set too high.  Meaning someone has screwed the idle screw out too far.  Probably because the Idle Speed Control Motor is dead.  Same thing happened to me on the same model car. Replacing the ISC Motor is extremely easy to do, a replacement cost me $135AU.

Aug 24, 2008 | 1993 Hyundai Elantra

1 Answer

No spark in one cylinder


Hi,

Pls try to check/replace your distributor cap and/or the rotor. A friendly reminder, pls check that the spark plug gaps are within specifications, the wider the gap the the more arcing from the rotor to the bottom terminals of the distributor cap, the faster the burning/deterioration. If at all possible, try to replace with Bosch or Beck Arnley brands.

Hope this be of initial help/idea. Pls post back how things turned up or should you need additional information.

Good luck and kind regards.

Thank you for using FixYa.

Jul 03, 2008 | 1994 Hyundai Excel

Not finding what you are looking for?
1998 Hyundai Elantra Logo

Related Topics:

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...