Question about 1994 Chevrolet Corsica

1 Answer

Ignition locked in run position and will not shut off

The ignition is locked in run position and I cannot get it to shut off

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Need new ignition switch, or if it's an automatic, the shifter linkage might be stuck or broken, (linkage that allows key to turn off when put in park.)

Posted on Feb 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition switch stuck in ''on'' position


Unplug the electrical connection on the ignition coil

May 30, 2010 | 1996 Mercury Sable

2 Answers

Ignition


the actuator inside the sterring column that the lock cylinder turns is boken, this is a very complex job and is not for the home tech without a factory service manual.

Apr 21, 2010 | 1996 Ford Taurus

1 Answer

How do i replace the ignition switch in my 94 couger


Removal & Installation
  1. Disconnect the negative battery cable. Remove the upper steering column shroud by removing the self-tapping screws.
  2. Unfasten the four bolts retaining the lower steering column shroud, then remove the shroud.
  3. Remove the lock screw, and detach the ignition switch electrical connector.
  4. Rotate the ignition switch lock cylinder to the RUN position.
  5. Remove the two screws retaining the ignition switch, and disengage the ignition switch from the actuator.
To install:

NOTE A new replacement switch will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch run position.
  2. Check to make sure the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock approximately 90 degrees from the LOCK position.
  3. Install the ignition switch assembly into the column actuator hole. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  4. Install the retaining screws and tighten to 53–71 inch lbs. (6–8 Nm).
  5. Attach the electrical connector to the ignition switch. Tighten the lock screw to 7–11.5 inch lbs. (0.8–1.3 Nm).
  6. Connect the negative battery cable. Check the ignition switch for proper function, including the START and ACC positions. Also, make sure the column is in the LOCK position.
  7. Install the upper and lower steering column steering shrouds.

Feb 10, 2010 | 1994 Mercury Cougar

2 Answers

Need to change the Clutch Pedal Ignition Switch; do you have instructions how to do this?


Removal & Installation
  1. To prevent accidental air bag deployment, disconnect the negative battery cable, then the positive battery cable to allow residual energy in the air bag system to drain.
  2. Remove the steering column shroud(s).
  3. Disengage the wiring harness connector from the ignition switch.
  4. Insert the key into the ignition switch, then rotate the ignition key lock cylinder to the RUN position.
  5. Remove the two screws attaching the ignition switch.
  6. Disengage the ignition switch from the actuator pin and remove the switch.
To install:
A new ignition switch purchased from Ford will already be set in the RUN position.
  1. Adjust the new ignition switch by sliding the carrier to the RUN position.
  2. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  3. Install the ignition switch onto the actuator pin.
  4. Align the switch mounting holes and install the attaching screws. Tighten the screws to 50-69 inch lbs. (6-8 Nm).
  5. Attach the electrical connector to the ignition switch.
  6. Connect the positive, then the negative battery cables. Check the ignition switch for proper function in START and ACC positions. Make sure the column is locked in the LOCK position.
  7. Install the steering column shroud(s).
Is this the one you are asking about?

Dec 07, 2009 | 1995 Ford Mustang

2 Answers

Car still running after take key out . cheked barrel thats ok don't know if it's relay problem


I think you have a bad ignition switch, not the ignition lock cylinder. they are 2 different things.

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.

Nov 21, 2009 | 1996 Ford Taurus

1 Answer

How hard is it to change the Ignition Key Lock Cylinder? Do I need to take off the Steering wheel or does the guts just come out from the Steering Col with a pin, or something?


this is the oldest info I have. should be similar

Section 11-05: Steering Column Switches 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable. Remove the upper steering column shroud by removing the four or five self-tapping screws. Remove tilt steering column lock lever (if so equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.
  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to ensure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and tilt steering column lock lever (if so equipped).

Nov 06, 2009 | 1992 Lincoln Town Car

1 Answer

My key will start the car but it wont turn the car off i have to unplulg the distributor to kill theh car. Also the ignition switch in the car rotates all the way around but it has always done that it just...


the ignition switch is an electrical part. The lock cylinder is whre the key goes and it activates the ignition switch. If you pulled the lock cylinder out, you could operate the car with a screwdriver.
Either you have damaged the ignition switch where the lock cylinder goes into it, or the lock cylinder is damaged where it fits into the ignition switch.

this is 96 taurus, don't have 92 sorry

Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Ignition Switch Removal
  1. Disconnect battery ground cable (14301).
  1. Remove lower instrument panel steering column cover (04459).
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Disconnect the ignition switch electrical connector.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.
Installation
  1. NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

    Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch pin into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install lower instrument panel steering column cover with screws.
------------------
Section 11-05: Steering Column Switches 1996 Taurus, Sable Workshop Manual
DESCRIPTION AND OPERATION Ignition Switch The ignition switch (11572), which is mounted on the steering actuator housing (3F723), operates in the following manner:
  • The ignition switch is cycled through rotation of the ignition switch lock cylinder (11582) through a pin which is part of the ignition switch.
  • The ignition switch lock cylinder also controls the mechanism which provides a positive lock for the transaxle linkage and the steering system.
  • The locking mechanism is located in the steering column housing.
The ignition switch lock cylinder positions are:
  • ACC
  • LOCK
  • OFF
  • RUN
  • START
The key can be removed from the ignition switch lock cylinder with the column-shift transaxle only when the shift lever is in PARK position and the key is in LOCK position.
  • The ACC position operates while the steering and transaxle remain locked.
  • The engine shuts off when the key is turned to the OFF position without locking the steering or transaxle.
Blade Type
The ignition switch has blade-type terminals that engage with one multiple connector. The multiple connector is secured to the ignition switch by an integral connector fastener.

May 05, 2009 | 1992 Mercury Sable

2 Answers

96 ford windstar ignition probs


the ignition switch is the electrical part behind the lock cylinder where the key goes in.

Ignition Switch Lock Cylinder
Lock Cylinder Functional
Removal
  1. The following procedure applies to vehicles that have a functional ignition switch lock cylinder (11582) and keys. If the key numbers are known, the correct key can be made. Disconnect the battery ground cable (14301). For additional information, refer to Section 14-01 .
  1. Turn the ignition switch lock cylinder to the RUN position.
  1. Place a 3.17-mm (1/8-inch) diameter wire pin or small drift punch in the hole in the steering column shroud under the ignition switch lock cylinder. Depress the retaining pin while pulling out on the ignition switch lock cylinder to remove it from the housing of the steering column.
Installation
  1. Install the ignition switch lock cylinder by turning it to the RUN position and depressing the retaining pin. Insert the ignition switch lock cylinder into the steering column housing. Make sure the ignition switch lock cylinder is fully seated and aligned in the interlocking washer before turning the key to the OFF position. This will permit the retaining pin of the ignition switch lock cylinder to extend into the hole of the steering column.
  1. Using the key, rotate the ignition switch lock cylinder to make sure of correct mechanical operation in all positions.
  1. Connect the battery ground cable.
-------------------------------------------------------------------------------------
Ignition Switch Removal
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove the upper steering column shroud (3530) by removing the four or five self-tapping screws. Remove key release lever (3F527) (if equipped).
  1. Remove lower steering column shroud.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition switch lock cylinder (11582) to the RUN position.
  1. Remove the two screws retaining ignition switch (11572).
  1. Disengage the ignition switch from the actuator.


71f4c5f.gif


Item Part Number Description 1 11572 Ignition Switch 2 — Ignition Switch Lock Cylinder Housing 3 — Slot in Lock/Column Assembly A — (Part of 11572) Pin B — Alignment Mark
Installation
NOTE: A new replacement ignition switch assembly will be set in the RUN position as received.

  1. Adjust the ignition switch by sliding the carrier to the ignition switch RUN position.
  1. Check to make sure that the ignition switch lock cylinder is in the RUN position. The RUN position is achieved by rotating the ignition switch lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the ignition switch slightly back and forth to align the ignition switch mounting holes with the lock cylinder housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is in the LOCK position.
  1. Install upper steering column shroud.
  1. Install the lower steering column shroud and key release lever (if equipped).

Feb 27, 2009 | 1996 Ford Windstar

1 Answer

I need instructions on how to put a locksmart switch ingnition


Removal
  1. Disconnect battery ground cable. Remove the steering column shroud by removing the four or five self-tapping screws. Remove tilt lever (if so equipped).
  1. Remove instrument panel lower steering column cover.
  1. Disconnect the ignition switch electrical connector.
  1. Rotate ignition key lock cylinder to the RUN position.
  1. Remove the two screws retaining ignition switch.
  1. Disengage the ignition switch from the actuator.
Installation
  1. Adjust the ignition switch by sliding the carrier to the switch RUN position. NOTE: A new replacement switch assembly will be set in the RUN position as received.
  1. Check to ensure that the ignition key lock cylinder is in the RUN position. The RUN position is achieved by rotating the key lock cylinder approximately 90 degrees from the LOCK position.
  1. Install the ignition switch into the actuator. It may be necessary to move the switch slightly back and forth to align the switch mounting holes with the column lock housing threaded holes.
  1. Install retaining screws. Tighten to 5.6-7.9 Nm (50-69 lb-in).
  1. Connect electrical connector to ignition switch.
  1. Connect battery ground cable. Check ignition switch for proper function, including START and ACC positions. Also, make certain that the column is locked in the LOCK position.
  1. Install instrument panel lower steering column cover.
  1. Install the steering column trim shrouds and tilt lever (if so equipped).

Feb 26, 2009 | 1991 Lincoln Town Car

Not finding what you are looking for?
1994 Chevrolet Corsica Logo

Related Topics:

193 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6876 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...