Question about 1994 Ford Probe

1 Answer

Cv axle replacement on a 05 mazda 626 do i need a pulley or can i just tap it out

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 33 Answers

Should pry or tap out

Posted on Feb 20, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the full front axle be exchanged from a 02 mazda 626 to a 97 mazda 626?


You install a complete reman front drive axle

If you like, you can buy a new one,for more money

The CV Joints (2) are part of the axle assy,you
will see that in the pictures your ordering from

You order parts that are application specific

No need to worry what fits another vehicle

Have to get the correct side,they are different lengths
& part numbers

Sep 30, 2014 | 1997 Mazda 626

1 Answer

How 1996 mazda 626 front axle shield broken


The drive shaft has to be removed to replace the rubber boot .you will have to dismantle the CV joint , clean and repack the joint with special grease and fit a new boot.

May 10, 2014 | 2001 Mazda 626

1 Answer

Cant get bolts out of cv axel support braket in a mazda 626


This is a bracket mount that has the axle shaft going thru it on the passenger side . the axle must be removed from mount before it can be removed . there is a single bolt that presses against the axle shaft bearing and a snap ring that holds the bearing in the mount once removed the axle will slide out .

Mar 21, 2014 | 1997 Mazda 626

1 Answer

Cv joins - knocking


If they're a knockin, they won't last long. Time for an axle replacement. You can get re-built axles for this car, less expensive and easy to replace. You DON'T want them to break while you are driving!! DANGER!!

May 29, 2013 | 1999 Mazda 626

1 Answer

Hi, The front end of my mazda clunks real bad and loud, while turning the wheel at any speed. Both directions. Help!


Check boots on CV joints for tears. Torn boots result in CV wearing out. The boots are at each end of the axles going from your transmission to the front wheels. The normal repair is to replace axles. Both can be more carefully inspected on a lift before deciding if only one or both axles should be replaced. Any questions, please reply. I'm going to bed now, but will answer any replies tomorrow.

Sep 10, 2010 | 1993 Mazda 626

1 Answer

Mazda 626 popping noise in front driver side when turning and or body shifting


Your Constant velocity joints have gone bad. the Boot that holds th grease has leaked out all the grease and the bearing inside are not being lubicated and thats where the poping comes from. Have someone look at the axle (CV) to determine if repairable or you might have to replace the axle. Hope this helps

Jun 27, 2009 | 2000 Mazda 626

1 Answer

Mazda 626


First put a jackstand under the car have it jacked up fairly high where you can get under it easily then take a really strong regular screw driver or a small pry bar slide up between tranny and the axle piece you are trying to get out and tap with your hand or a rubber mallet the bottom of the pry bar or the handle of the screw driver towards the opposite side of the car of what you are working on.

May 18, 2009 | 2000 Mazda 626

2 Answers

Clicking sound when turning hard or in reverse turning....


Usually that is the sign of a cv joint going. I have an accord with front wheel drive and it did the same thing. THe cv boot being torn could have caused the initial breakdown of the bearing faces...

Mar 27, 2009 | 1995 Mazda 626

2 Answers

Sounds like the axle popping


well turn the wheel to the right or left and look at the boots on the cv shafts if the are torn open the shaft will need to be replaced.

Jan 08, 2009 | 1999 Mazda 626

Not finding what you are looking for?
1994 Ford Probe Logo

Related Topics:

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...