Question about 1990 Jeep Cherokee Limited

1 Answer

Oil line whats the differance between the upper and lower transmission oil line, where are both of them located on the transmissioin

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The upper is the in line from the trans cooler the lower is the return line // both screw in to the side of the trans

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove radiator on 2000 Lincoln Continental


RADIATOR
Removal
1. Disconnect battery ground cable.
2. Drain engine cooling system as described.
3. Remove engine air cleaner.
4. Remove upper radiator hose from water bypass tube.
5. Remove radiator overflow hose from radiator and fan shroud.
6. Remove transmission oil cooler line from oil cooler inlet fitting.
7. Remove nuts retaining A/C condenser core to the radiator.
8. Disconnect engine control sensor wiring from the auxiliary electric cooling fan motors and the CCRM.
9. Raise vehicle on hoist.
10. Remove splash shield from lower radiator support and front sub-frame.
11. Remove lower radiator hose from radiator.
12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
14. Support fan shroud, radiator and A/C condenser core with a suitable jackstand. Remove lower radiator
support.
15. Position jackstand aside and carefully remove radiator and fan shroud.
16. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
17. Remove upper radiator hose from radiator.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
NOTE: Loosen transmission oil cooler lines while securely holding radiator
connector with a back-up wrench.
18. Remove the radiator.

Oct 21, 2016 | Lincoln Cars & Trucks

1 Answer

How do I remove a radiator in a 2000 Chevy Silverado 1500 pickup


Gasoline Engines
  1. Drain the cooling system.
  2. Unfasten the upper fan shroud bolts and remove the upper fan shroud.
  3. If equipped, remove the upper panel fasteners and the panel.
  4. If equipped, remove the upper insulators and brackets.
  5. Disconnect the radiator upper and lower hoses and, if applicable, the transmission coolant lines.
  6. Remove the coolant recovery system line, if so equipped.
  7. Remove the oil coolant lines, if equipped.
  8. Remove the lower fan shroud bolts and the lower fan shroud.
  9. Remove radiator from the lower brackets and insulators.

Jul 28, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

How do i remove radiator


What type of engine is in this car. i can tell you this, the radiator removal on this car is not an easy one, let me see if engine size makes a difference.okay here we go,remove the negative cable from the jumper terminal or battery.
1) drain cooling system.
2) remove radiator upper cross member.
3) remove the upper and lower radiator hoses
4) remove the transmission hoses from cooler
5) remove oil lines from cooler if it has them,
6) remove connector from cooling fans and then remove fans.
7) remove the a/c condenser bolts located on the front of radiator.
8) remove fastener holding bracket for transmission cooler lines to left side of radiator. left side is driver side.all views are done from inside car.
9) lift a/c condenser upward to disconnect from radiator and then set back down on lower cross member. no need to open or discharge a/c system,
10) lift radiator up and out , careful not to damage lines or condenser.
I will enclose a few pictures to help you locate a few parts to remove.5_28_2012_11_24_21_pm.gif5_28_2012_11_24_43_pm.gif5_28_2012_11_26_11_pm.gif5_28_2012_11_26_27_pm.gif

May 28, 2012 | 2003 Chrysler 300M

1 Answer

How to remove radiator


  1. Drain the cooling system.
  2. Unfasten the upper fan shroud bolts and remove the upper fan shroud.
  3. If equipped, remove the upper panel fasteners and the panel.
  4. If equipped, remove the upper insulators and brackets.
  5. Disconnect the radiator upper and lower hoses and, if applicable, the transmission coolant lines.
  6. Remove the coolant recovery system line, if so equipped.
  7. Remove the oil coolant lines, if equipped.
  8. Remove the lower fan shroud bolts and the lower fan shroud.
  9. Remove radiator from the lower brackets and insulators.
  10. To install:

    1. Install the radiator on the lower brackets and insulators.
    2. Install the lower fan shroud and its retaining bolts. Tighten the shroud bolts to 71 inch lbs. (9 Nm).
    3. Attach and tighten the engine oil cooler pipe bolts to 18 ft. lbs. (24 Nm) and the transmission oil cooler bolts to 19 ft. lbs. (26 Nm).
    4. Attach the lower and upper radiator hoses..
    5. Install the upper insulators, the upper fan shroud and fan shroud bolts. Tighten the shroud bolts to 71 inch lbs. (9 Nm).
    6. Attach the coolant recovery system line, if so equipped.
    7. If equipped, install the upper panel fasteners.
    8. Refill the cooling system.

Jan 13, 2011 | 2001 Chevrolet Silverado 2500HD

1 Answer

How do I remove the radiator form my 1997 ford taurus do I have to remove the bumper?


No,

Section 03-03: Engine Cooling 1997 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Radiator Aluminum Core, Crossflow
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service interval of Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.
  1. Disconnect battery ground cable (14301).
  1. Remove battery (10653) as described in Section 14-01 .
  1. Remove clip retaining contant control relay module and position module aside.
  1. Remove battery tray (10732) as described in Section 14-01 .
  1. Remove radiator cap (8100).
  1. Raise vehicle on hoist as described in Section 00-02 .
  1. Remove radiator splash shield.
  1. Drain engine cooling system as described in this section.
  1. Remove the radiator mounting bracket assembly.
  1. Remove lower radiator hose (8286).
  1. Partially lower vehicle.
  1. Remove upper radiator hose (8260).
  1. Remove radiator overflow hose (8075).
  1. Remove upper A/C condenser core retaining bolts.
  1. Remove upper transmission oil cooler tube clips.
  1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
  1. Raise vehicle on hoist.
  1. Remove lower transmission oil cooler tube clips.
  1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
  1. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  1. Remove lower A/C condenser core bolts and position A/C condenser core (19712)aside.
  1. Remove radiator support bracket.
  1. Remove radiator (8005).

Jan 13, 2011 | 1997 Ford Taurus

2 Answers

How to remove radiator from my 2000 chrysler 300


Radiator Removal & Installation To Remove:
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect negative cable.
  3. Drain cooling system.
  4. Remove or disconnect the following:
    • Radiator upper crossmember
    • Upper and lower coolant hoses from the radiator
    • Transmission hoses from cooler
    • Engine oil cooler lines (if equipped)
    • Radiator fan electrical connector and fan assembly
    • Condenser mounting screws located at the front of the radiator
    • Transmission cooler line bracket from left side of radiator
  5. Lift condenser upward enough to disengage upper mounting clips. Allow condenser to rest on lower radiator crossmember.
  6. Lifted radiator from engine compartment.
To Install:
  1. Seat the radiator assembly lower rubber isolators into the mounting holes in radiator lower support.
  2. Attach air conditioning condenser to radiator
    • Torque to 45 inch lbs. (5 Nm)
  3. Install or connect the following:
    • Radiator lower hose
    • Transmission cooler line bracket and transmission hoses
      1. Torque to 28 inch lbs. (3 Nm)
    • Radiator fan and electrical connector
    • Engine oil cooler lines (if equipped)
      1. Torque to 160 inch lbs. (18 Nm)
    • Radiator upper hose
    • Radiator upper support crossmember
    • Negative cable
  4. Fill cooling system with coolant.
prev.gif next.gif

Aug 03, 2010 | 1999 Chrysler 300M

1 Answer

How to remove and replace radiator on 1998 ford taurus


  1. Disconnect battery ground cable.
  2. Remove the battery.
  3. Remove clip retaining constant control relay module and position module aside.
  4. Remove battery tray.
  5. Remove radiator cap.
  6. Raise vehicle on hoist.
  7. Remove radiator splash shield.
  8. Drain engine cooling system.
  9. Remove radiator mounting bracket assembly.
  10. Remove lower radiator hose.
  11. Partially lower vehicle.
  12. Remove upper radiator hose.
  13. Remove radiator overflow hose.
  14. Remove upper A/C condenser core retaining bolts.
  15. Remove upper A/C transmission oil cooler tube clips.
  16. Remove upper transmission oil cooler tube (7C410) using 3-8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  17. Raise vehicle on hoist.
  18. Remove lower transmission oil cooler tube clips.
  19. Remove lower transmission oil cooler tube using 3/8 inch fuel line disconnect tool 310-041 (T90T-9550-C).
  20. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  21. Remove lower A/C condenser core bolts and position A/C condenser core (19712) aside.
  22. Remove radiator support bracket.
  23. Remove radiator.

May 07, 2010 | 1998 Ford Taurus

2 Answers

How to remove a radiator from a ford taurus


Disconnect battery ground cable. Remove battery. Remove battery tray. Remove clip retaining contant control relay module and position module aside. Remove radiator cap. Raise vehicle front end as high as possible. Remove radiator splash shield. Drain radiator. Remove the radiator mounting bracket assembly. Remove lower radiator hose. Partially lower vehicle. Remove upper radiator hose. Remove radiator overflow hose. Remove upper A/C condenser core retaining bolts. Remove upper transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Raise vehicle. Remove lower transmission oil cooler tube clips. Remove lower transmission oil cooler tube. Remove transmission oil cooler bracket and position transmission oil cooler aside. Remove lower A/C condenser core bolts and position A/C condenser core aside(be careful not to loosen the AC condenser lines. Remove radiator support bracket. Remove radiator out through the bottom of the vehicle.
Installation
Position radiator. Position radiator support bracket and tighten nuts. Position A/C condenser core and tighten lower A/C condenser core bolts. Position transmission oil cooler tube and install transmission oil cooler tube bracket. Install lower transmission oil cooler tube. Install lower transmission oil cooler tube clips. Install lower radiator hose. Install radiator mounting bracket assembly. Tighten bolts. Install radiator splash shield. Lower vehicle. Install upper tranmission oil cooler tube. Install upper transmission oil cooler tube clips. Install upper A/C condenser core retaining bolts. Tighten bolts. Install radiator overflow hose and tighten clamps securely. Install upper radiator hose. Position constant control relay module and clip securely. Install battery tray. Install battery. Connect battery ground cable. Fill and bleed cooling system. Start engine and inspect for leaks.

Nov 25, 2009 | 1998 Ford Taurus

1 Answer

I am trying to find out how to disassemble the radiator support in my 1999 Chevy Suburban and I am having some difficulities.


  1. Drain the cooling system.
  2. Unfasten the upper fan shroud bolts and remove the upper fan shroud.
  3. If equipped, remove the upper panel fasteners and the panel.
  4. If equipped, remove the upper insulators and brackets.
  5. Disconnect the radiator upper and lower hoses and, if applicable, the transmission coolant lines.
  6. Remove the coolant recovery system line, if so equipped.
  7. Remove the oil coolant lines, if equipped.
  8. Remove the lower fan shroud bolts and the lower fan shroud.
  9. Remove radiator from the lower brackets and insulators.

    0900c152802490af.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Exploded view of the radiator mounting


    0900c152802490b0.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Remove the radiator upper panel fasteners


    0900c152802490b1.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Remove the radiator upper panel


    0900c152802490b2.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Disconnect the transmission cooler lines

Sep 02, 2009 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

I need 2 know how to remove the radiator


THIS IS a 1995 LINCOLN CONTINENTAL W/4.6L ENGINE
iIBELIEVE TOWN CAR IS DIFFERENT LET ME KNOW IF SO AND PLEASE DONT FORGET TO RATE ME


REMOVAL
  1. Disconnect battery ground cable (14301).
  2. Drain engine coolant.
  3. Remove engine air cleaner (ACL) (9600).
  4. Remove upper radiator hose (8260) from water bypass tube.
  5. Remove radiator overflow hose (8075) from radiator (8005) and fan shroud (8146). NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  6. Remove transmission oil cooler line from oil cooler inlet fitting.
  7. Remove nuts retaining A/C condenser core to the radiator.
  8. Disconnect engine control sensor wiring (12A581) from the auxiliary electric cooling fan motors and the CCRM.
  9. Raise vehicle on hoist.
  10. Remove splash shield from lower radiator support (16138) and front sub-frame (5C 145).
  11. Remove lower radiator hose (8286) from radiator. NOTE: Loosen transmission oil cooler lines while securely holding radiator connector with a back-up wrench.
  12. Remove oil transmission cooler line from oil cooler outlet fitting on radiator.
  13. Remove retaining screws for power steering/transaxle oil cooler and position cooler aside.
  14. Support fan shroud, radiator and A/C condenser core (19712) with a suitable jackstand. Remove lower radiator support. Position jackstand aside and carefully remove radiator and fan shroud.
  1. Remove two retaining bolts for fan shroud at top of radiator and remove fan shroud from radiator.
  2. Remove upper radiator hose from radiator.
INSTALLATION
  1. Follow removal procedure in reverse order.
  2. Tighten fan shroud bolts and A/C condenser core nuts to radiator to 3-5 Nm (27-44 inch lbs.) .
  3. Tighten lower radiator support bolts to 8-11 Nm (71-97 inch lbs.) .
  4. Tighten transmission oil cooler lines to fittings to 25-28 Nm (18-21 inch lbs.) .
  5. Tighten power steering/transaxle oil cooler and splash shield retaining screws securely.
  6. Refill engine coolant.

Feb 11, 2009 | 1995 Lincoln Continental

Not finding what you are looking for?
1990 Jeep Cherokee Limited Logo

Related Topics:

115 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...