Question about 2004 Toyota Sienna
Warning light on the left side of my dashboard has 2 small arrows pointing to each other and it looks like it has a horse shoe around the arrows. cannot locate manual what does this warning light mean?
That symbol is the low tire pressure light. You have a tire that is right at the minimum threshold. The light goes off as the tire temperature rises, and, as the temp rises, the internal air pressure also rises slightly. Just check the tires with a good pressure gauge, inflate them to the specs printed on the tag inside your driver's side door, and you will be just fine.
Thanks for choosing FixYa for assistance.
A FixYa rating (4 blue diamonds) would be greatly appreciated. Thanks in advance.
Posted on Feb 20, 2009
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Tips for a great answer:
Dec 20, 2013 | 2007 Toyota Sienna
Oct 16, 2012 | 2006 Toyota Sienna
I've made up the following instructions, on how to clear VSC & TRAC Warning lights:
Zero Point Calibration of Yaw Rate and Deceleration Sensors Using Paper Clips (or jumper wires).
First, locate the 16-pin ODB II connector under the steering wheel (beneath the dash). The pins are numbered sequentially backwards from right to left (from the wide side of the connector looking at it from underneath).
Take two normal-sized paper clips (or suitable jumper wires). If using paper clips, straighten one edge of one of the paper clips. For the other, bend it open to a 90-degree angle (like an elbow).
Insert one paper clip/wire into pin # 14 (Ts), and the other paper clip/wire into pin # 4 (CG) of the OBD II connector - DO NOT allow the paper clips/wires to make contact at this point. 1. Ensure the shift lever is in "P" range. Verify that the VSC indicator light is illuminated, indicating the Recorded Zero point is erased.
Refer to diagram below:
2. Turn the ignition switch to "ON" (not start).
3. Momentarily touch the two paper clips/wires together (short) and separate again (open) - Repeat this process 5 times (within 8 seconds of turning ignition on).
4. Turn the ignition switch "OFF".
5. Remove both paper clips/jumper wires from the OBD II connector.
6. Turn the ignition switch "ON" (not start) - wait until VSC warning light turns off (approx. 20 seconds), then wait 2 seconds.
7. Turn the ignition switch "OFF".
9. Re-insert paper clips/jumper wires to terminals #4 & #14 of the OBD II connector (as per above diagram).
10. Turn the ignition switch "ON" (not start) - VSC warning light should remain illuminated for 4 seconds, then start flashing at 0.13 second intervals.
12. After VSC warning light flashes for 2 seconds, turn the ignition switch "OFF".
13. Remove paper clips/jumper wires from the OBD II connector.
Drive your vehicle to confirm VSC & TRAC warning lights have been reset and no longer illuminate.
"If this has helped you resolve your issue, please be kind enough to leave a testimonial"
1. Ensure the shift lever is in "P" range.
Verify that the VSC indicator light is illuminated, indicating the Recorded Zero point is erased.
Jun 10, 2011 | 2001 Toyota Sienna
Mar 03, 2010 | 2004 Toyota Sienna
Sep 28, 2009 | 2004 Toyota Sienna
Aug 06, 2009 | 2007 Toyota Sienna
May 19, 2009 | 2001 Toyota Sienna
Apr 13, 2009 | 2003 Toyota Corolla
Mar 26, 2009 | 2007 Toyota Sienna
Jan 16, 2009 | 2007 Toyota Sienna
3,551 people viewed this question
Usually answered in minutes!