Question about 1987 Audi 5000 CS

1 Answer

NEED NEW KEY

Lost one and only ignition key for the car need new one

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 359 Answers

If you go to ebay, under "audi 5000 87 ignition" you will see the full ignition block with new keys, and its only $49, and you can offer less since its best offer. You can check local junk yards, and parts stores, but you may not find the part due to the age, hope that helps

Posted on Feb 20, 2009

  • Alan Conner
    Alan Conner Feb 20, 2009

    If you go to ebay, under "audi 5000 87 ignition" you will see the full ignition block with new keys, and its only $49, and you can offer less since its best offer. You can check local junk yards, and parts stores, but you may not find the part due to the age, hope that helps

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How can I hot wire my ford Taurus? I lost my key


Problem with hot wiring the ignition is that the vehicle will start and run but with out turning the ignition the steering wheel will be locked > I suggest a new ignition switch , you can always hammer a flat head screw driver in the ignition were the key goes and turn the ignition. Either way you will need a new ignition switch .

Apr 03, 2015 | 1994 Ford Taurus

1 Answer

Will a bad key ignition switch effect the inderctor light on the dishboard


New keys with cylinder may not have a transponder chip , or new keys will need to be programmed. you will require two keys equipped with proper transponder for your vehicle, and either new keys cloned with the old transponders. If you have lost the original keys , you will need someone to remove the original keys from the pcm , than marry the 2 new keys to the pcm. If you have an original key , try placing it by the lock cylinder when attempting to start with the key supplied with the new ignition cylinder.

Nov 08, 2014 | 2001 Ford Expedition

1 Answer

Lost my remote on my 02 jeep liberty and need to


the key fob? or radio remove or what?
remote to what.

the operators manual covers this , under car keys.
the car came with 2 Fobs. lost them both now>?
RKE its called, (makes looking fact more easy)
is this car with SKIS Immoblizer option> yes./no
if yes.
SENTRY KEY IMMOBILIZER SYSTEM - IF
EQUIPPED
im reading your operators guide now.
lost that too>?
Duplication of keys may
be performed at an authorized dealer (or locksmiths) or by using the
Customer Key Programming procedure.

DIY, takes 1 key , good, called a valid key, in the below text.
You can program new keys to the system if you have two
valid keys by doing the following:
1. Cut the additional Sentry Key Transponder blank(s) to
match the ignition switch lock cylinder key code.
2. Insert the first valid key into the ignition switch and
turn the ignition switch ON for at least 3 seconds but no
longer than 15 seconds. Turn the ignition switch OFF and
remove the first key.
3. Insert the second valid key and turn the ignition
switch ON within 15 seconds. After ten seconds, a chime
will sound and the SKIS indicator light will begin to
flash. Turn the ignition switch OFF and remove the
second key.
4. Insert a blank Sentry Key into the ignition switch and
turn the ignition switch ON within 60 seconds. After 10
seconds, a single chime will sound. The SKIS indicator
light will stop flashing, turn on for 3 seconds; then turn
off.
The new Sentry Key has been programmed. Repeat this
process to program up to a total of 8 keys.


did i guess right, the Key FOB RKE,
remove key entry fob.?

Sep 18, 2014 | 2002 Jeep Liberty

1 Answer

Lost key and alarm dodge caravan


to reprogram new key first you need to use 2 factory program keys.place first factory key in the ignition first turn ignition on for 3 seconds. then turn off ignition then install second factory in the ignition on position for 10 seconds.when immobilizer warning lamp begins to flash a acoustic signal is emitted.within 60 seconds. switch ignition off and remove key.then insert new key and switch on for 10 seconds a acoustic signal is emitted and immobilizer warning lamp remain illuminated for 3 seconds indicating programming completed.if all fails dealership has to reprogram new keys.

Dec 17, 2012 | 2000 Dodge Caravan

1 Answer

Lost ignition key on 2006 pontaic grand prix


go to GM dealer with VIN and proof of ownership and order new key.

Apr 08, 2012 | 2007 Pontiac Grand Prix GXP Sedan

1 Answer

Need new ignition key. lost key to ignition


buy a new ignition and if you dont want to replace the original with the new one just have an approved locksmith re-key your ignition and door locks to use the new one.

Feb 22, 2010 | 1988 Buick Century

2 Answers

Lost key


Get out your wallet and go to the dealer! Not much else you can do. Those keys have imbeded security chips that must be programed by thr dealer.

Jun 16, 2009 | 2006 Chevrolet Equinox

1 Answer

02 Park Ave, Need to know how to program new key to ignition.


Take the original key, if you have it. Start the car, kill the car then start it with the new key. This will work for adding a key. If you are replacing a lost key then you will have to learn it to the theft system.Place the key in the ignition, turn it to run for 10 min. Cycle it off then back to run for 10 min. Cycle it off then back to run for 10 moer minutes. When the 30 minutes is up turn it off then try to start it. Thai should work. I have had to do it more than once. Good Luck

May 07, 2009 | 2000 Buick Century

1 Answer

Changing ignition key switch


Well,

From what I remember you need to put the missing key in and then press the cylinder release, a small hole by the ignition switch. Without the key, I guess you would need a locksmith to turn the tumbler then press the switch. Lock pick set anyone?

Jul 18, 2008 | 1986 Chevrolet Caprice

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70346 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13527 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...