Question about 2001 Chevrolet Blazer

1 Answer

Fuel filter i have tried to replace the fuel filter but i cant get one end louse and do not want to twist fuel line

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 118 Answers

Its not too uncommon for the lines to be extreamly tight due to corrosion and other factors...enough said.get some GOOD penetrating oil (not wd-40)spray it a couple of times throughout the day,let it sit all night and the most important thing is that you use the correct kind and size wrench you need Line Wrenches get a good one not a cheepo,the filter should have a 13/16 or so hex to put a good open end wrench and hold it as you use the line wrench on the line end.hope it works have a good day DB

Posted on Feb 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the best way replace the fuel lines. and what kind of lines can i use


I take it that you replaced the fuel filter as it is probably blocked now.. Fuel continually flows through the lines and it would take a big piece to block them unless it is the fine filter at the end of the pickup pipe in the tank

Mar 09, 2013 | Cars & Trucks

1 Answer

Where do I locate the fuel filter on a 93 Chevy Blazer s10 Tahoe with a 4.3 votec engine?


It's attached to the frame underneath,right about where the driver's door ends,or slightly farther back.
If you're going to change it,first soak the fittings with some brand of penetrating oil,even WD40 if that's all you have. You need 2 wrenches on each end,probably 5/8 and or 9/16 (16mm & 14mm roughly) and try your best not to twist the fuel lines,rusty or not. They twist pretty easy that's why there are 2 wrench fittings on each end.
Good or bad,please rate my post?
Bob

Aug 14, 2010 | 1993 Chevrolet S-10 Blazer

1 Answer

Need to replace fuel filter


The fuel filter is mounted on the floor pan just in front of the fuel tank Use compressed air or carburetor cleaner to clean any dirt surrounding the fuel inlet and outlet line fittings. Once all the dirt has been removed, twist the two lines a quarter-turn in opposite directions to loosen the fitting. Depress the white plastic quick-disconnect tabs and detach the inlet line from the fuel filter (see illustration [see comment below marked "#2"] ). Note: Have spare rags or a small container to catch or wipe up extra gasoline that will spill from the filter assembly. Use an open end wrench to steady the outlet side of the filter and a flare nut wrench to unscrew the fuel line nut, then separate the outlet line from the filter while noting the installed position of the O-ring. Using a flare nut wrench will help to avoid rounding the corners off of the fuel line nut. Detach the fuel filter mounting bracket bolt and remove the fuel filter. Installation is the reverse of removal. Note: Be sure to install a new O-ring on the outlet line before reassembling. "Squeeze the white plastic quick-disconnect tabs together and pull the inlet line (A) away from the filter, then detach the outlet line (B) from the fuel filter - unbolt the filter mounting bracket to remove the fuel filter".

Jul 08, 2010 | 2000 Pontiac Grand Am GT

2 Answers

How do I change the fuel filter in a 1970 Caddy Fleetwood, 472 ci and where is it?


If you can locate where the fuel line goes into the Carb. Remove the fuel line then the larger nut behind that.The fuel filter is inside the larger nut.It is hard to try and get the fuel line off without both moving or twisting the fuel line,and most times there is not enough room to bend it out of the way to get the fuel filter out.If all else fails you can cut the metal line just leave a few inches back from the nut then when reinstalling you can patch it back with a rubber fuel line and clamps.You may also look into installing a inline fuel filter in better location.Well hope this helped.

Feb 08, 2010 | Cadillac Fleetwood Cars & Trucks

2 Answers

How do you change the fuel filter. are there tools you use or do you just unscrew it and just pull it apart.


The filter is located under the passenger side directly under the door area.

Depend on the fuel system. if fuel injected, remove the fuel pump fuse, start the car. this will release the pressure on the pump. follow the gas line to find the filter, remove and replace with a new one. make sure you take the pressure off the system before you start. you could end up with a twisted fuel line and that is a bigger problem.


After done, replace the fuse, restart the car. it may take a few cranks to get it running. make sure the vehicle is secured on jack stands before you crawl under.. after the vehicle is started. check the entire lenght of the fuel line, for leaks. hope it helps. duboff. if not fuel injected, follow the fuel lines to the filter. some engines have the filter in the carb. it is a good idea to have gas line plug to prevent gas from running all over.

Sep 16, 2009 | 1992 Buick LeSabre

2 Answers

Removing original fuel filter on 96 grand am


if original, don't worry about the black cap and tabs on the non-threaded end of the filter connection. Unfortunately, you have to literally pull the heck out of it to separate it from this connection. What is holding it in is a metal "barbed" collared sleeve inside the connection. Try using a pliers on the cable side (don't bend or break!) and work the filter off using elbow grease. Not fun, but it worked. The FRAM replacement filter simply snapped right in.

May 24, 2009 | 1996 Pontiac Grand Am

1 Answer

Were is the fuel Filter


LOCATION OF FILTER IS DRIVER SIDE FRAME RAIL ABOUT AT DRIVER DOOR HARD TO SEE BUT FALLOW FUEL LINE ITS THERE. hOPE THIS HELPS PLEASE RATE ME !! THANK YOU AND GOOD LUCK

TOOLS Are Simple and inexpensive local Parts Store like AutoZone will Have it

FUEL FILTER REPLACEMENT

TOOLS REQUIRED
J-46363 Fuel Line Release Tool

REMOVAL PROCEDURE

  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  2. Raise and suitably support the vehicle. Refer to Vehicle Lifting.
  3. Remove the fuel composition sensor bracket nuts.Reposition the fuel composition sensor/bracket off to the side
    1. Using a flare nut wrench and backup wrench disconnect the fuel line fitting from the fuel filter.
    2. Pull the quick connect fitting back until the internal retainers hit the filter stop.
    3. Twist one end of J-46363 and insert it between the fitting and the filter.
    4. Twist the opposite end of J-46363 and insert it between the fitting and filter.
    5. Once J-46363 is inserted, ensure that J-46363 is parallel to the filter and fitting.
      1. While holding the filter, push the fitting towards the filter in order to disconnect the quick connect fitting.
      2. Remove the fitting from the filter.
      3. Remove J-46363 from the filter.
        1. Remove the fuel filter from the bracket.
        INSTALLATION PROCEDURE
      4. Install the NEW fuel filter to the bracket.While holding the filter, push the fitting towards the filter in order to connect the quick connect fitting
      5. Using a flare nut wrench and backup wrench connect the fuel line fitting to the fuel filter.
        1. Position the fuel composition sensor/bracket into place. NOTE: Refer to Fastener Notice in Service Precautions.
        2. Install the fuel composition sensor bracket nuts. Tighten the nuts to 17 N.m (13 lb ft) .
        3. Lower the vehicle.

Apr 07, 2009 | 2005 Chevrolet Avalanche

2 Answers

How to uninstall fuel filter for 1993 3.3l V6 Dodge Dynasty


GRAB PLIERS SQUEEZE THE HOSE AROUND THE FUEL FILTER AND TWIST SLIGHTLY. BE SURE NOT TO GRIND THE PLIERS AROUND THE HOSE.

Feb 23, 2009 | 1993 Dodge Dynasty

1 Answer

Removing fuel filter


it takes a special tool to disconnect these lines. go to your local auto parts store and ask for the fuel line disconnect tool.once you have the tool put it on the fuel filter prong that the fuel line is connected to and slide the tool up into the gas line, at the same time pull the line away from filter. you may half to try this several times.also when the tool slides up into the line twist the line and push in and out. in short thare is a spring up in that line that gets stiff and corroted so moving the line around while the tool is in place helps free up this sprind.also spray a little lubracant in the ends of the lines before beginning.

Jan 14, 2009 | 1998 Ford Expedition

2 Answers

UNABLE TO GET FUEL FILTER REMOVED


due to the position of hte filter it is very tough but with the right tool every thing is possible so you have to get the tool a crow foot wrench i think it is 18mm and hold one end with a wrench and twist the ****** out of there if you feel the line is turning i would take it to a pro.

Nov 14, 2008 | 1999 Chevrolet Cavalier

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...