Question about 2002 Buick Rendezvous

2 Answers

Rear window do not go down - 2002 Buick Rendezvous

Posted by on

  • 2 more comments 
  • Kenneth Sullivan Feb 23, 2009

    no !

  • Kenneth Sullivan Feb 23, 2009

    No!

  • letishia88 Mar 31, 2009

    Rear window has all of a sudden jammed shut, wont go down at all, its a manual window, have taken off the door panel but can make any sense of it..... any ideas thank you.....

  • Douglas May 11, 2010

    I have to ask is the window lock on?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My brother just came by and all he did was hit the motor with a hammer and it work belive it .

Posted on Mar 14, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 59 Answers

This is a hard one as one window not working will likely mean the motor has gone bad, but normally the drivers front goes first as it gets the most use. If a person had the door panel off and could unplug the motor and had a simpe test light they could clip the ground to the car and test each wire for power as the switch is pushed up and down. If getting power and still is not going up or down then the motor would need to be replaced. Sorry for the earlier question Thank you,

Posted on Feb 24, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 gmc envoy Windows fuse


Are all windows not working ? Two separate circuit breakers left & right . Both in rear fuse box . Fuse Block - Rear Beneath the left rear seat
Check for broken wires inside the rubber boot from body to doors.
Do you know about electronic control modules ?
The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.

Check

Oct 21, 2016 | 2003 GMC Envoy

1 Answer

Is there a fuse for the window switch


Which window switch ? RT DOOR CB-circuit breaker , do you know what a circuit breaker is ? 25A (System power for right rear window)
LT DOOR CB 25A (System power for left rear window
The power window system will operate anytime the retained accessory power (RAP) system is active or when the ignition switch is in the ACCY or ON position.
The DDM contains 4 power window switches which are integral components. Closing any of the normally open, rocker type switches provides the DDM with a request for power window operation. The switches for the 2 front windows have 3 positions Up, Down and Express Down, while the switches for the rear windows have only 2 positions, Up and Down. Each of these switches and their positions is a direct input into the DDM. Upon receiving a request for power window operation, the DDM, transmits a class 2 message indicating the switch and it's changed position.
The PDM contains a single power window switch that is an integral component. Closing of this normally open, rocker switch provides the PDM with a request for the front passenger power window operation. The switch for the front passenger window has 2 positions Up and Down. Each of these switch positions is a direct input to the PDM.
The 2 rear passenger doors have there own switches. Each of the switches contain a power window up and down relay. A switch activation alone can control the up and down functions of the rear windows. However the BCM, upon receiving a class 2 message from the DDM, can control the set of relays which will activate the rear window motors.


The power window system consists of the following components:
?€¢
Driver door module (DDM)


?€¢
Passenger door module (PDM)


?€¢
Body control module (BCM)


?€¢
LR power window switch


?€¢
RR power window switch


?€¢
Window up and window down relays in each of the rear passenger window switches


?€¢
Window lockout switch


?€¢
Reversible power window motors in each of the doors (circuit breaker protected)


?€¢
LT DOOR CB 25A (System power for left rear window)


?€¢
RT DOOR CB 25A (System power for right rear window)


If you not sure about any of this I suggest you take your vehicle to a ASE certified repair shop .

Oct 08, 2015 | 2002 Chevrolet TrailBlazer

3 Answers

My back automatic window went down and now won't come back up. No sound from motor. Checked fuses. Even took back seat apart but don't know what to do or what caused it. How can I get window to go...


it may need to be reset.

SECTION 501-11: Glass, Frames and Mechanisms 2001 Explorer Sport/Sport-Trac Workshop Manual
GENERAL PROCEDURES Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions.
------------------------------------------------------------------------------------
  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.
  • Go To Pinpoint Test K .

------------------------------

Sep 15, 2011 | 2001 Ford Explorer Sport Trac

1 Answer

Where is the rear window relay located on the 2002 Ford Explorer sport trac. Not the rear door windows but the very back window.


  • The power rear window is inoperative (Explorer Sport Trac only)
  • Circuitry.
  • Battery Junction Box (BJB) fuse 3 (30A).
  • Central Junction Box (CJB) fuse 20 (7.5A).
  • Power rear window control switch.
  • Rear window glass motor.

NOTE: The power rear window motor is not on the multiplex link. Any diagnosis and testing carried out on the power rear window will not involve the GEM module. NOTE: The reinitialization procedure must be carried out when repairs are performed on any part of the power rear window system including when the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.

Rear Window Motor Initialization s1r~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.
NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window module is installed, and any operation in which grease or lubricants are applied to the power rear window system.
NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.
NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.
NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.
NOTE: Steps 7 and 9 require that the power rear window control switch be held in the closed position until the power rear window motor stalls the window in the upper header seal. Step 8 requires that the window control switch be momentarily turned to the open position.
  1. Start with the ignition in the OFF position.
  1. Turn the ignition to the ON position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the OFF position.
  1. Press the power rear window control switch vent button six times.
  1. Turn the ignition to the ON position. The power rear window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialized mode.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls in the upper header seal.
  1. Momentarily rotate the power rear window control switch to the open position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.
  1. Rotate and hold the power rear window control switch to the closed position until the window stalls into the upper header seal. Once this operation is complete, the window will move up-down-up-down approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.
  1. Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions
---------------------------------------------------------------------------------------------

Nov 16, 2010 | 2001 Ford Explorer Sport Trac

2 Answers

The passenger rear window won't roll up or down from the drivers controle it clicks in the passenger front door. it will roll down in the passenger rear door but not up. the window modulator rolls up and...


I have the exact same problem on a Jeep Grand Cherokee 2004. The rear passenger window rolls down only from the rear passenger window and won't go up or down from the front. It has to be in the wiring because the problem was intermittent initially and a new window motor does the exact same thing. If you figured it out or have the wiring diagram please let me know.

Apr 22, 2010 | 2004 Jeep Grand Cherokee

2 Answers

My rear windows will not raise down..or up on


There is a button on the master switch (drivers) to turn off the rear windows make sure it's not depressed. If not the master switch is probably bad since you lost both rear window control . Power and grounds to the rear switches comes from the master switch.

Sep 27, 2009 | 1999 Dodge Durango

1 Answer

Neither rear window will roll down using the rear controls. They both work fine using the driver's master controls. Also the passenger rear window rolls down, on its own, when the switch is on.


Is you car fitted with a childlock safety switch for the rear windows?

If so the windows will work from the front but will be locked out to the rear seat passenger

Jun 29, 2009 | 2005 Cadillac CTS

2 Answers

Replaced battery on freelander rear window will not stay up carried out procedure in manual but window goes up beeps and goes down.no problem at all untill battery replaced.


disconnect battery reconect after 5 mins on reconnection rear window will go down , use key in rear lock to reset rear window, door lock should now work, if not try rear door relays behind left hand rear panel.

Jun 13, 2009 | 2002 Land Rover Freelander

1 Answer

Rear window diagram for 2000 lincoln ls. The rear


You need a window regulator, and should do the motor at the same time.

Mar 13, 2009 | 2001 Lincoln LS

4 Answers

Back door wont open and window wont go down


The rear window has to be completely down in order to move the tailgate! You should be happy that your window is stuck up, unlike mine which is stuck all the way down! I have to completly take apart my tailgate!! If you want to try a trick to get the rear window down, my bronco has a rear window switch right next to the headlight knob, take the 2 purple wires on that window switch, and cross them, if your motor still works and if the wires are good, that should make the window go down!!! good luck, hope that helps!

Oct 05, 2008 | 1995 Ford Bronco

Not finding what you are looking for?
2002 Buick Rendezvous Logo

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...