Question about 1999 Chrysler Sebring

1 Answer

How do you change rear hub on sebring convertible

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,011 Answers

Take off tire remove brake caliper then rotor tap on rotor it will slide off remove dust cap loosen 30mm. nut then slide off the hub .this job is not bad to do.

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you access the rear strut assembly on a 2004 Sebring Convertible? The videos show a trunk access but its not there?Is it located behind the back seat?


its in the trunk area over the wheel. you have to remove the trunk liner panel and then you can access the strut mounting bolts

Feb 17, 2015 | 2004 Chrysler Sebring Convertible

1 Answer

How do i remove the rear brake rotors on a 2004 chrysler sebring convertible?


there are two bolts holding the caliper bracket on. then after that they tend to get stuck to the hub. i usually tap on the rotor with a hammer to get them loose

Jul 02, 2014 | 2004 Chrysler Sebring

1 Answer

When it rains my sebring convertible has water sloshing in the rear somewhere. is there a drain that empties this problem if so where is it exactly could you please tell me exactly were the drain holes are...


yes there are holes. the holes are on both sides of the back window. climb in back seat and look under the back window on the side rear quarter panel inside you will one on each side

Nov 04, 2012 | 1998 Chrysler Sebring

2 Answers

Tire specs for 2001 chrysler sebring


HI. Here is the complete line up of specs concerning your vehicles front and rear tires. You did not post the trim line of this car, so I posted all models and tire combination's specified by the manufacture.


2001 Chrysler Sebring Lim 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LX 2 Door Coupe Front and Rear Tires P205/55R16
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/65R15
2001 Chrysler Sebring LX 4 Door Sedan Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Convertible Front and Rear Tires P205/60R16
2001 Chrysler Sebring LXi 2 Door Coupe Front and Rear Tires P215/50R17
2001 Chrysler Sebring LXi 4 Door Sedan Front and Rear Tires P205/60R16

Jul 06, 2010 | 2001 Chrysler Sebring

1 Answer

Worn rear wheel bearing, 2004 chrysler sebring, non a.b.s.


REMOVE THE REAR DRUM OR ROTOR,REMOVE DUST CAP FROM BEARING..REMOVE RETAINING NUT..HUB/BEARING WILL SLIDE OFF SPINDLE..REVERSE PROCEDURE TO INSTALL..I HOPE THIS HELPS

Sep 10, 2009 | 2004 Chrysler Sebring

1 Answer

2001 Sebring LXI convertable. Loud rumbling noise that increases as accelerating increases. Sounds like a rumble strip on the highway. I changed the tires with no change in the noise.


Bad hub bearing. Drive the car on a straght EMPTY road .@30 mph or when noise is audible, **** the wheel left than right (similar to a race car warming. tires) and listen if there is a change in the sound if so its a front bearing if not it should be a rear bearing .Jack the rear of the vehicle up and spin the tire holding onto the strut. Feel and listen for a vibration or noise. This should pinpoint that elusive noise.Let me know Good hunting

Apr 11, 2009 | 1998 Buick Park Avenue

1 Answer

2005 sebring hub bearing replacement


This is actually not a dificult repair IF YOU TAKE YOUR TIME.
Start, of course, by raising and supporting the vehicle
remove the wheel(s) as needed
Remove the caliper, brake pads and caliper mounting braket
remove the rotor
remove the axle nut, there may be a cotter pin in the nut acting as a lock.
make sure the axle pushes in freely inside the hub, it's splined and sometimes seizes in, a puch and hammer will knock it free
there will be three bolts on the rear of the hub assembly that must be removed
remove the hub by hitting it with a hammer, sometimes the rear bearing seal stayes in place, remove this also
reverse these steps to install your new hub.

Questions, feel free to ask.
Good luck
R

Jun 06, 2008 | 2005 Chrysler Sebring Conv

1 Answer

1995 chrysler sebring lxi


there are four 18mm bolts on the opposite side of dust plate.once u remove thoe bolts,you'll have to either use a slide hammer, or the old fashion way a big hammer and smack it side to side.the whole hub and wheel bearing assembly will come out.The dust sheild is in between the hub and axel once it comes apart u will understand.

Jun 02, 2008 | 1995 Chrysler Sebring

Not finding what you are looking for?
1999 Chrysler Sebring Logo

Related Topics:

215 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...