Question about 2001 Hyundai Accent

1 Answer

How to change head lights of hyundai 1.3i

I just want to change my main head lights

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 98 Answers

OK> you may or may not want to disconnect the battery and take it out to give yourself more room. Once you have done this a time or two you will find that you can do it without taking the battery out. When you open up the hood and you are facing the car looking into the engine compartment (we will start with the battery side first). Where the headlights are on the front of the car, under the hood is where the bulb is located. You will see an electrical connector going into a black rubber cover. Peel the black rubber cover back and disconnect the electrical connector. Place the rubber cover to the side and on the inside you will see a very unusual looking paper clip contraption that holds the headlight bulb in place. The secret to this is that it is under tension and held in place in a slot at the bottom. All you need to do is press down, and move it sideways a little bit and it will pop out of the slot. When the paper clip contraption has come out of the slot at the bottom, simply lift it up, and the bulb will come right out. Put the new bulb in, slide the end of the paper clip contraption back into the slot in the bottom, place the black rubber cover back over the headlight area making sure the the (3) prongs from the light bulb are sticking out of the middle of the rubber cover, Re-connect the electrical connector, do the other side the same way and when you are done test the lights to ensure that they both work properly.

Posted on Feb 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Timing Settings


I need the tdc diagram and/ or setting for the ford bantam 1,3i 2006 model

Sep 09, 2013 | 2006 Ford Bantam 1.6i

1 Answer

Require torque settings for a hyundai tucson 2008,gls petrol engine


Specifically which torque settings are you referring to. There are thousands to choose from. Please give an example such as "differential carrier", "cylinder head", "exhaust manifold to engine block" etc.

Mar 31, 2012 | 2008 Hyundai Tucson

2 Answers

How do you replace the fog light bulbs on a 2007 hyundai sonata


Look under the bumper and you will see two large phillips head screws right in front of the wheels. Take these two screws out and bend/move the plastice piece out of the way. Now you can easily get to the bulb. There is a cap that twists off that protects the wires and back of the bulb. Twist this off and then remove the plug portion from the back of the bulb. The bulb then turns 1/4 to 1/2 revolution to loosen and remove. Reverse steps for installation.

Dec 19, 2009 | 2007 Hyundai Sonata Limited Sedan

2 Answers

Hyundai elantra 1.6GLS J2 torque settings


dear friend:here follows the settings in need:
cylinder head-30-35 nm + 30-35 + 65deg + 65deg.
mains-30nm +65deg
big ends- 1 - 26nm 2 - 52NM
fly-wheel -130nm
cam-sprocket - 100-120
crank-pulley - 170-180
cam caps -15nm

Aug 31, 2009 | 1995 Hyundai Elantra

1 Answer

2002 jeep cherokee brake lights blowing


A Hyundai Hyundai Sonata is NOT a 2002 Jeep Cherokee.

Jun 30, 2009 | Hyundai Motor 2004 Sonata

1 Answer

Head lights burning out


It is common for both headlight bulbs to burn out at once on a Hyundai. Use some dialetric grease on the headlight bulb connectors before inserting the connector into the bulb. Also check for the main ground in the area of the headlight harness and make sure it is good.

Jun 25, 2009 | 2001 Hyundai Tiburon

3 Answers

Head lights go out


you have a bad dimmerswitch

Feb 21, 2009 | 2002 Hyundai Santa Fe

3 Answers

Side light bulb change on hyundai terracan


hi there
the solution is simple,
you only need to undo the screw on top of the side light/indicator. then facing the head light place a flat headed screw driver under the bottom lip of side light. the bottom of the lihgt is on a small push fit stud, use a sponge or cloth to protect your bumper paint work then just apply pressure gently to lever side light out towards you, It will come dont worry, you may then change your bulbs if you wish remove the whole light unit you will see the bottom bolt as soon as you release the side light. to replace just push back into place then replace screw. whole job takes about five minutes

hope this helps kevan hildred

Nov 23, 2008 | 2003 Hyundai Tucson

1 Answer

Head lights wont turn off


if you are saying the front side lights are going off but the headlights remain on ? then could you try this ? put the h/lights on main beam mode then whilst on main beam turn off lights if h/lights go off now ? then with lights still off put onto dipped beam with the switch/stick if h/light come on it is most probably the dipped beam headlights relay that has gone faulty as the h/lights have 2x relays 1for dip +1 for main beam if the above does not make any difference ? it may well be the switch assy hope this helps

Oct 15, 2008 | 1997 Hyundai Accent

Not finding what you are looking for?
2001 Hyundai Accent Logo

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...