Question about 2002 Chrysler Town & Country

1 Answer

How to remove interior door panel on 2002 chrysler t & c???

Power window switch or motor not working. first problem is How to remove driver side door panel. do you have any photos to illustrate how to remove panel???

Posted by on

  • cockey216 Mar 13, 2009

    I had this same problem. Replaced the switch; doesn't fix it. Now we need to try to replace the motor. I've got 97K mileage on the car

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the driver side door panel on a 1994 Lincoln Mark VIII


Remove mirror mount cover assembly.
Remove inside door handle cup (22634).
Remove door lock control bezel.
Remove window control bezel.
Remove interior lamp lens.
Remove screw from interior lamp assembly body.
Remove screw from window control bezel opening.
Disconnect mirror, lock switches and memory seat on driver side from bezels and wire harness.
Disconnect window switches from window bezel and wire harness.
Lift front door trim panel (23942) vertically, out of weatherstrip and over lock rod.
Disconnect interior lamp (13776) from wire harness.
Remove front and rear door trim retention hooks into door inner panel.
To install, reverse Removal procedure, paying special attention when inserting inner door trim into weatherstrip. Rock inner door trim into weatherstrip and push downward until lower trim belt character ditch lines up with score mark on inner door panel.

Aug 16, 2014 | 1994 Lincoln Mark VIII

1 Answer

Odyssey power window switch


You will need to start with removing the drivers side interior door panel. You will need a test-light and check for power and ground at both the suspected switch and the window motor. At the switch, test for power and ground going into the switch. Then test he other side for power and ground going out. Test for power and ground at the power window motor too.Please write back with what you have found and write back, good luck.

Mar 08, 2014 | Cars & Trucks

2 Answers

How do i change the drivers side window motor an an 05 kia sedona


You have to remove the inner door panel to
access the window regulator

You remove the regulator & then the motor from it

You Tube Video will provide a visual of several
similar window motor replacement jobs

Go there-- enter your car,question ,details,etc--- then move
around the site to watch various things

Dec 09, 2012 | 2005 Kia Sedona

1 Answer

2005 Chrysler T&C passenger side window went down and won't come up. All other automatic windows and door locks work fine - don't hear any motor sound / buzz / etc. when either driver side or passenger...


If the window had not been slow in it's action before it stopped working I'm guessing you only have a connection problem. I would remove the door panel and using a multimeter check the hot wire to see if power is reaching the switch. If it is check the connection on the motor. If power is reaching the motor through the switch you have a faulty motor. If at any point of testing there is no power backtrack the power wire to find where the break is. (it's usually in the door jam)

Apr 13, 2010 | 2005 Chrysler Town & Country

1 Answer

2002 pontiac montana passanger pwr window


I beleive you need to change the Power Window Switches Module in the drivers side door panel, as these connections are interlinked within this module and it is usually the first part that fails. Especially that you already changed the switches & motor in the passenger door and it still does not work. Once you remove the dual switch module in the driver's side door, you will understand what I mean. Plus it is really easy to access. Good luck! I have the same model, Claude

Feb 19, 2010 | 2002 Pontiac Montana

1 Answer

How do I remove the driver's door interior panel? Power window only works intermittently.


1, Disconnect the cable from the negative side of the battery.
2. Pry the courtesy light from the panel, and disconnect the wiring connector.
3. Remove all panel retaining scews. Most are covered. Look carefully for them all.
4. Remove door switch panel and switch assembly.
5. Memory Seats/Mirrors? If so equipped use a small flat pry tool ( I use a upholstery tool) and remove the mirror/seat switch and disconnect.
6. Using the pry tool: satrting at the bottom: pry the panel away from the door. Continue on the sides.
7. Lift Up and off the top of the window sill and locking knob.
8. Disconnect and remaining wiring connections.
9. Disconnect the door handle rod. Unsnap the plastic keep off the rod, and remove "L" shape out of plastic keeper hole.
10. Note how the waterseal (plastic/rubber) is placed and what wiring connections come out what openings.
11. Remove the waterseal.
12, Most of the Power Window Motors will actually come with the rails and/or the cables attached.
13. The rest is pretty much remove the old motor and cables and replacing them with the new one's. I have faith the rst you can figure out.
Let me know if this helped or not or if you need any additional instructions let me know at fixya.com

Nov 23, 2009 | 2002 Chrysler Town & Country

3 Answers

The drivers side window stoped working on my 2004 silverado the passenger side works fine


Try the fuse. The switch may be faulty so check by removing the inner door panel and connecting a 12v battery via two wires to the motor that winds the window up and down. If it goes up and down it's probably the switch which may just need a clean on the terminals.

Nov 01, 2009 | 2002 Chevrolet Silverado 2500HD

1 Answer

Need to find a way to take off the drivers side window motor


Motor
  1. Disconnect the negative battery cable.
  2. Remove the door trim panel and watershield.
  3. Detach the motor wires at the multiple connector.
  4. Remove the motor retaining screws using Torx® drive bit set D79P–2100–T or equivalent, and separate the motor from the bracket and cable drum housing.
  5. Remove the motor from inside the door.
To install:
  1. Position the motor and drive to the cable drum housing and motor mounting bracket. Install the 3 motor screws and tighten.
  2. Connect the power window motor wiring.
  3. Connect the negative battery cable.
  4. Check window operation.
  5. Install the watershield and door trim panel.

Door Panel
  1. Disconnect the negative battery cable.
  2. Snap out the two door pull strap retaining screw covers. Remove the screws.

CAUTION To avoid breakage of the door pull covers, insert a small screwdriver diagonally between the pull strap and chrome bracket. Snap out both sides then remove.


  1. Remove the two screws on the front and rear side of the front door trim panel.
  2. Using the trim pad removing tool, pry the trim panel retaining clips from the door inner panel.

NOTE Do not use the front door trim panel to remove the trim clips from the door inner panel. Replace any bent, damaged or missing push pins.


  1. Remove the window regulator switch housing from the back of the front door trim panel. Lift up the housing and disconnect all connectors from the switch housing.
  2. Disconnect the driver seat regulator control processor switch if equipped.
  3. Twist out the interior lamp wire assembly.
To install:
  1. Ensure that the plastic watershield is secured to the door .
  2. Position the front door trim panel to the door. Connect the interior lamp wiring.
  3. Align door lock side to its mating slide on the sheet metal.
  4. Snap in the front door trim panel. Ensure all retainers fit properly. Install the two retaining screws on the front and rear side of the front door trim panel.
  5. Connect the driver seat regulator control processor, if equipped.
  6. Position the window regulator control switch housing and connect the switch connectors. Install it to the front door trim panel by snapping it in, or by installing the screw at the rear.
  7. Install the two retaining screws and pull strap covers.
  8. Connect the negative battery cable.
053777a.gif

Aug 27, 2009 | 2000 Lincoln Town Car

1 Answer

Driver's side power window will not work


Remove door panel to check wiring to switch and motor
See if motor is getting power through the switch - if so motor is bad
If no power to motor check operation of switch - jump wires to test
if window works bad switch

thanks.

Jul 08, 2009 | 2003 Mazda MPV

1 Answer

Power window does not work


you need to buy or make a clip removal tool. it looks like a sturdy 2 prong fork to pry off the plastic clips.this id whats holding the interior panel and some screws holding the door opener

May 30, 2009 | 2002 Chrysler Town & Country

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

1,308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...