Question about 1993 Toyota Corolla

1 Answer

How do i replace the female end of the front passenger seatbelt?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Toyota Master
  • 61,037 Answers

U can't replace parts of seat belts, u either must buy an entire belt assembly or find a used one, which I don't recommend, the reason they don't sell parts is safety related.

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The male end of my seatbelt won't lock into the male end?


Check for something stuck in the female end or where it plugs in, if it is clean then you will likely have to change it.

Sep 17, 2014 | Cars & Trucks

1 Answer

Remove Back Seat of 2007 Toyota Avensis to replace seatbelt


Seat base is not bolted.Grab under front of base with both hands near the ends and just snatch up quickly.Pull the seat base out from the car and the bolts for seat belts are visable.

Apr 09, 2014 | 2007 Toyota avensis 1.6

1 Answer

Seatbelt switch locked and won't release


i have seen this before oddly and i hope this works for you but penatrating oil helped me in the past just to free it up but your car is alot newer so im thinking maybe there is some junk inside the buckle like coffie or what ever

hope this helps you out

Dec 02, 2013 | 2012 Toyota Sienna Base 7-Passenger...

1 Answer

2006 grand cherokee seat belt


Have the same problem in my 98 Toyota Rav4. I squirted the female buckle (bolted to seat, not holding strap harness) with wannabe WD-40 lubricant from the $1 store, and it seem to have solved the problem. I'm guessing the spring mechanism is worn out, which is why the harness buckle won't lock. Another solution is to replace the female lock buckle with an identical part from the used parts junkyard store.

The seatbelt light on the dash stays "on," even when everyone has their belt on, but I don't bother servicing that. If yours have an audible alarm instead of an indicator light on the dash, locate the source of the alarm sound and disconnect the wires to silence the sound.

Nov 29, 2013 | Cars & Trucks

1 Answer

Front passenger seatbelt on a 2005 volkswagen passat won't engage on the receptacle


remove it and bang it while it upside down something might have fallen into it like change

Oct 10, 2012 | 2005 Volkswagen Passat Sedan

1 Answer

On my 91 civic all the seatbelts are fastened and the seatbelt light still flashs and the warning beeper is beeping how can i resolve this prob.?


My guess, the switch that is in the female end of the drivers side seat belt. The switch is bad or it's come unpluged or it's corroded. It's hard to get at without pulling the seat (four bolts and a harness plug). The plug for the seatbelt plug is usually under the carpet but if you pop off the plastic cover over the bolt that holds the female end of the belt to the car body there is usually enough slack in the wire to pull it up enough to see if the plug or wire is broken or corroded. If not, pull the bolt (it will be lock-tited in so it will come out hard). If the wire looks good, ground the lead wire (wire that goes to the drivers side female end of the setbelt). If the light goes out the switch in the female end of the belt is bad. If it still does,t go out, well I'd have to be there to troubleshoot it further.
Hope this helps.

Mar 26, 2011 | 1991 Honda Civic

1 Answer

Had to cut wires attached to female seatbelt receptacle to replace seatbelt and now dim headlight on that side(passenger side) won't work. How do I splice to get headlight to work again?


Check your ground wire going to that headlight - I have had to run a new wire in the past, just went to a good ground spot on the car and ran it to the black wire on the headlight plug, making sure you cut that wire loose from the car side of the plug.

Nov 03, 2010 | 2004 Mitsubishi Galant

1 Answer

The seatbelt sometimes gets stuck and won't release. My kids try to buckle and sometimes it works and other times it doesn't.


Spray a little of WD-40 into the female end of the belt assembly. Wrap it in a clean cloth to prevent over spray, and try working the male end into the female connector. You may have to do this several times to achieve a positive result. Otherwise you may have to replace the entire seat belt assembly.

Sep 14, 2010 | 2006 Hummer H3

1 Answer

2003 Crown Victoria-Position of seatbelt female buckle hurts me.


Can they be poked down and then brought up where you say? I had this on a lincoln town car and they were long enough without an extension. The mounting bolts are really made in only one spot usually and are very importantly secured. You could always just buy a female strap without any plastic on it and run it whever you want. A lot of RV places carry them :>) Hope this helps.

Jun 28, 2009 | 1989 Ford Crown Victoria

2 Answers

Seat Belt chime


get an extra seatbelt claspmale end and put it in the female end this way you don't have to altar the car in anyway just unclasp it when your ready to sell your car.

Jun 10, 2008 | 2006 Pontiac G6

Not finding what you are looking for?
1993 Toyota Corolla Logo

Related Topics:

151 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...