Question about 1999 Chevrolet Blazer

1 Answer

Starting Problems AGAIN

I have been having troubles with my 99 Chevy Blazer for about the past 3 months. I just recently had it worked on by a chevy dealer. the security system fried the wires to transmission and fuse box. Now that I have it back a month later it wont start again. IT doesnt make the sound that the starter is even workin at all...It starts when it wants to. The only thing I can hear when I try to turn it over is the fuel pump turning on.

Posted by on

  • 2 more comments 
  • A Oliver Feb 22, 2009

    no when it went to garage they removed the security system or disconnected it or something. Put in a new starter and still no different.

  • A Oliver Feb 23, 2009

    i called the garage that removed the security system said pretty much that i would have to pay them all over again just for them to look at it, and tell me if there is something else wrong or something that they didnt fully fix.

  • skibrat3 Mar 20, 2009

    I had my transmition replaced and the alternator and a few months later my car started to do as you described, it wont turn over it just clicks, and if I wait about a half an hour it will start,

  • Bruce Bracey
    Bruce Bracey May 11, 2010

    Do you have any kind of security or remote start system on the vehicle?

    Let me know.




1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 1,000 Answers

Personally, I would return it to the dealer and state that is still not fixed.
When the remote start / security system was removed or disconnected, the starter circuit would have had to be rewired as the remote start / security system prevents the starter from engaging.
The wire splicing that would have had to take place may still be a problem.
If you would rather diagnose this problem your self I will be happy to help.
Let me know.

Posted on Feb 23, 2009

  • Bruce Bracey
    Bruce Bracey Feb 24, 2009

    Sorry to here that, it's a shame the shop doesn't stand behind their work.

    If you are able to use a test light and can work with a wiring diagram we can start working to solve the problem

    Let me know.




1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

99 Chevy S10 Blazer that seems to start in second gear

run fault codes to check for servo/ solenoid problems --TCM faults

Jan 28, 2014 | Cars & Trucks

1 Answer

1999 chevy blazer not starting

Check the plug wire from the ignition coil to the distributor cap.
If you haven't already, replace the distributor cap and rotor.
The GM Vortec's have issues with moisture getting inside the cap and rotor and causing problems.

Apr 24, 2012 | 1999 Chevrolet Blazer

1 Answer

I have a 99 Chevy Blazer, I have had it for about six months or so. The past month and a half, it pops out of 2 wheel drive and into 4 wheel drive (sometimes blinking back and forth between 4 hi and 4 lo)....

I have the same trouble. It seems a relay is keeping it in 4wheel drive. I havne't solved the trouble yet. It may be a loose or corroded wire in the connector to the TCCM located in the passenger kick panel. Dealer part about $450 or more. For the moment I took out the fuse for the 4 wheel drive. It is located in the lower right hand side in the fuse the box under the hood. It disengages the 4wheel drive and I replace the fuse if I need the 4wheel drive.

Aug 26, 2010 | 1999 Chevrolet Blazer

1 Answer

Trouble code for transmission

This code stand for transmission fluid pressure switch manual valve position switch assembly malfunction. Kind of a long winded term for the switch that tells the computer what gear you want to be in. Often when I see this it means that the switch [not the transmission] is going bad. This switch is mounted on the valve body inside the transmission. Fairly easy to test but you do need to have some transmission experiance to do so. Good luck and hope this helps a bit.

Jun 30, 2010 | 1999 Chevrolet Blazer

1 Answer

'99 chevy blazer 4x4 LT

the heater issue is probaly a short in wiring. the tire is a wheel bearing needing replaced.

Apr 06, 2010 | 1999 Chevrolet Blazer

1 Answer

1997 chevy blazer trouble starting

97 don't have carb that year its TBI injection . Inspect/fuelpump relay/pressurereg.switch/pump/filter

Nov 18, 2008 | 1997 Chevrolet Blazer

3 Answers

2003 Chevy Blazer won't start

have the computer checked out. may need reprogramming and have updates added. also check for loose or corroded connections at the terminals.

Aug 27, 2008 | 2003 Chevrolet Blazer

Not finding what you are looking for?
1999 Chevrolet Blazer Logo

250 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides