Question about 2000 Dodge Caravan

1 Answer

How to install ignition switch cylinder on 86 Honda Accord

How do i install an ignition switch cylinder on a 1986 Honda Accord? I had some one else take it out for me and they told me to try putting the new one in my self but for some reason it won't go all the way in

Posted by on

  • fcardona89 Feb 19, 2009

    thank you so much...went in easily like you said

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 107 Answers

Line up the switch and tumbler , by turning key in the the tumbler and flat blade screwdriver in the switch
should click in easily

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

'86 honda accord 4 cyl...runs very rough as though missing on 1 cyl ...when removing plug wires 1 at a time each 1 removed makes engine run worse except for #1 cyl which when removed smooths engine out...


no, the plug is firing. But the timing is off. the plug is firing quite a bit before top dead center on that cylinder. The burning of the fuel mixture is occurring while that piston is on its way up and is slowing it down---dragging down the whole engine. i think you should change the distributor cap and rotor as cylinder one is firing at the same time as cylinder 2or 4. This indicates a possible carbon track in the distributor cap.

Feb 12, 2011 | 1986 Honda Accord

1 Answer

I have an 86 mustang 5.0 .When I turn the key to the on position, the warning lights in dash do not cycle as they should.I replaced the ignition cylinder, no such luck... Any ideas out there????


If your fuses are good, and no loose wires, try the ignition switch, not lock cylinder, the ignition switch is located on the steering column about two-three inches away from the ignition lock cylinder towards the dash on the steering column.

Feb 10, 2011 | 1986 Ford Mustang

1 Answer

86 Honda Civic 1.3 Still no fire. Replaced the


good day Sir, try to check the spark plugs hope it will help you

Mar 01, 2010 | 1986 Honda Civic

1 Answer

Idle


If the ignition timing is incorrect and or someone has turned on the idle screw without bypassing the PCM. Otherwise the IAC(idle air control motor) is defective. Possible vacuum leak also.

Feb 13, 2010 | 1986 Honda Accord

1 Answer

I need fuze box layout for 1986 Honda Accord


Connole, what fuse are you looking for? My 86 Accord has the cover so I could tell you. Or, if you email me at c.easy.c@gmail.com I can email a photo of the cover to you.

Chris

Feb 13, 2010 | 1986 Honda Accord

2 Answers

Need to install head gasket on 86 honda accord .Is it worth the effort


Only if the rest of the car is in good (perfect) condition. If not then I would not replace the head gasket. Head gaskets dont just go bad, overheating is what causes the gasket failure, then the head will be warped and need to be repaired/ straightened, Then you will need to fix why it overheated in the first place.

Dec 15, 2009 | 1986 Honda Accord

1 Answer

86 honda accord


which lights headlights if so are they flip up lights?

Nov 03, 2009 | Cars & Trucks

1 Answer

Car was stolen broke the ignition


REMOVAL

  1. On models equipped with airbag, disarm airbag as described under MAINTENANCE PROCEDURES/AIRBAG SYSTEM DISARMING.
  2. On all models, disconnect battery ground cable.
  3. Remove ignition switch as described under STARTING AND CHARGING SYSTEMS/COMPONENT REPLACEMENT AND REPAIR PROCEDURES/IGNITION SWITCH.
  4. Remove key light case from lock body, if equipped.
  5. On 1989 Accord models, place ignition lock cylinder in the ACC position.
  6. On except 1989 Accord, place ignition lock in the I position.
  7. On all models, position suitable punch into hole on lock cylinder housing and depress pin, then remove lock cylinder from housing.
INSTALLATION

  1. On 1989 Accord models, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the LOCK position.
    2. Rotate key until it is almost at the ACC position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to ACC position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. On except 1989 Accord, install ignition lock cylinder as follows:
    1. Place ignition lock cylinder in the O position.
    2. Rotate key until it is almost at the I position, then insert lock cylinder until pin contacts housing.
    3. Rotate key to I position, then push pin in and insert lock cylinder into housing until pin clicks into place.
  1. Install ignition switch and connect battery ground cable.
SRS wire harness is routed near the ignition switch.

CAUTION:
  • All SRS electrical wiring harnesses are covered with yellow outer insulation.
  • Before disconnecting the SRS wire harness, install the short connector on the airbag.
  • Replace the entire affected SRS harness assembly if it has an open circuit or damaged wiring.
IGNITION SWITCH
  1. Remove the steering wheel, then remove the steering column covers.
  2. Disconnect the 7-P connector from the under-dash fuse box.
  3. Insert the key and turn it to "0."
  4. Remove the 2 screws and replace the base of the switch.

Feb 13, 2009 | 1992 Honda Accord

Not finding what you are looking for?
2000 Dodge Caravan Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...