Question about 1984 Chevrolet S-10

1 Answer

84 s10 oil pressure

I found a oil pressure switch for a 84 blazer on ebay would this work on my 84 s10 pickup? and how do you take it off I think it just un screws but not shure and do i have to drain my oil or anything?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 142 Answers

Yes that switch will work. So will a lot of other parts and gaskets. You have to make sure the engine size is the same. Parts are compatible with the same engine size. Have a drain pan and new oil ready in case the oil does come flowing out.
Please remember to rate this solution.

Posted on Feb 19, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure/fuel pump switch located on a 1994 chevy blazer s10


I will assume this is a 4.3 engine, the oil pressure /fuel switch is located on the rear of the engine next to distributor, what is the problem?

Dec 08, 2012 | 1994 Chevrolet S-10 Blazer

1 Answer

Where is the oil pressure sensor lacted on a 1996 s10 2.2 Pickup


How much below 30 is it dropping? Oil pressure when in DRIVE at idle on a hot engine, is NORMAL at around 18 to 20 Psi. The warning lamp does not come on until around 7 Psi.

With that said, the oil pressure switch (for the light) is located on the lower left front of the engine. The fuel pump oil pressure switch and sender (for the gauge and fuel pump operation) is on the lower right front of the engine.

May 20, 2012 | Cars & Trucks

1 Answer

I have a 1997 Chevy Blazer that has oil, but no pressure


There's something you can do to check if the oil pump is still working screw off the oil filter and start it only for a few seconds if oil shoots out the pump is working if it doesn't the pump could be clogged or it lose prime if it's working check the wire going to the oil pressure switch may be broken.

Jan 04, 2010 | 1997 Chevrolet Blazer

1 Answer

84 chevy s10 2.8L


if your pressure is too low this fix is quite expensive and not worth for older cars, so the first thing you should try to keep it running is to use THICKER OIL (W20-50 or such), + oil stabilizier (any good oil additive). I tried it in my Jeep,- helped right away.. Good luck

Jul 28, 2009 | 1984 Chevrolet S-10

2 Answers

My 84 blazer wont shift


Your 84 wiring harness is for the TCC ( transmission converter control) system.
On the left side of the carburetor (driver side) you should have 2 cables, one for the accelerator and the 2nd for the TV (throttle valve) control. You will need to adjust the cable for correct shift points. Under normal circumstances you will have 7 to 10 mm's extending beyond the cable adjuster block.
Should take care of the issue for you.
Let me know.
Regards,

Apr 05, 2009 | 1984 Chevrolet Blazer

1 Answer

84 s10 oil pressure switch


There is nothing wrong with buying parts on ebay. If you don't mind the wait, in my experience you will save. Just make sure it is the right on for your truck, but i think most oil sending units for G.M. are pretty much the same, especially the older ones. If you are unsure message the seller, I am sure they will be glad to help. You don't have to drain, just unplug it then screw it off, when reinstalling it I would put some Teflon tape on the threads to prevent any leaks

Feb 18, 2009 | 1984 Chevrolet S-10

1 Answer

1984 s10 2.8 manual trans. flywheel causes engine to vibrate


no should be same engine. check your engine mounts and tranny mount. how bad a vibration? sometimes after installing engine the trans gets shifted around and if mount was worn it will allow it to hit crossmeber and vibrate.

Jan 16, 2009 | 1984 Chevrolet S-10

1 Answer

94 s10 4x4 will not lock in


I have this problem on my 95 S10 blazer and found the switch on the dash was the problem.

Good luck
Rob

Dec 07, 2008 | 1994 Chevrolet S-10

1 Answer

Blazer will not start has spark and fuel pressure


the problem is common for the 93-94-95 4.3 vortex its the spider injection located inside the plenum the part costs between $250 to 400 i had to replace on girlfreinds 94 blazer. ifound one o ebay for $100

Nov 06, 2008 | 1994 Chevrolet S-10 Blazer

1 Answer

Oil Pressure Problem?


just fixed that problem myself. it was an oil pressure sending unit. twelve dollar part. and i was thinking oil pump or something... 12 dollar part. oil pressure sending unit.

Sep 18, 2008 | 1989 Chevrolet S-10 Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70365 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...