Question about 1999 Isuzu Rodeo

1 Answer

The location of the ecm fuse on 98 isuzu rodeo

Just trying to find out where the ecm/ecu fuse is located to reset the ecm

Posted by on

  • c38hot May 11, 2010

    disconnect battery for 5 minutes , sometimes there is more than just one fuse , proper scantool can reset codes , hard codes will reappear when there is a problem

  • Anonymous Mar 13, 2014

    cannot locate ecm computer on car?


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that hasĀ over 10 points.


    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 1 Answer

ECM fuese are located in the fusebox in the engine compartment-left sidefacing the vehicle.

Posted on May 01, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the ecm fuse located on a 1992 cutlass

It Is located in the under hood fuse and relay center, it is marked "ECU" pull it for 5 minutes to reset.

Oct 10, 2016 | 1992 Oldsmobile Cutlass Supreme

1 Answer

Where is the ecu ig fuse located on 95 camry v6?

The ECM fuse should be located under the hood in the fuse box. The bottom side of the lid will tell you which one it is.

Sep 21, 2016 | 1995 Toyota Camry

2 Answers

Are there a way to reset the computer on a 96 Isuzu Trooper

the ECU , reset on all cars has 3+ ways.
all do.
1: scan tool push reset button (best of best)
key off.
2: pull the ECU memory fuse for 5min put back,
3: pull battery neg lug for 5min put back.
4: Pull ECU, (gross way) but does 2 trick.

usa answers only... and not stated by you. (yours)
that fuse is called

ECM 30amp, F-3 (fuse relay box)
it is the memory fuse, and is hot all the time, (for memory retention)



Oct 25, 2015 | Isuzu Cars & Trucks

1 Answer

Cadillac ecu

    • 1 Turn the ignition switch to "Off."
    • 2 Pull down on the top of the fuse panel lid beneath the steering column. Remove the fuse panel lid.
    • 3 Grasp the fuse that is labeled "ECM" or "ECU." The inside of the fuse panel lid shows a chart indicating where each fuse is located.
    • 4 Pull the fuse straight out of the fuse panel to remove it.
    • 5 Turn the ignition switch to "ON" without starting the engine. Leave the Cadillac in this state for five minutes.
    • 6 Turn the ignition switch off.
    • 7 Replace the fuse into its slot in the fuse panel. Press in on the fuse until it is fully inserted. Replace the fuse box cover.

Jul 08, 2014 | 2002 Cadillac Deville

1 Answer

Ecm fuse location 2001 chevy astro van

The power for the data link connector is from a 25amp fuse Number 7 in the IP fuse box. As long as the check engine light is on the computer has power.
The main computer power is from two ECM fuses in the box near the battery.
The fuse locations should be in the back of your owners manual.

Dec 20, 2012 | 2001 Chevrolet Astro

1 Answer

Where is 2003 chevrolet tahoe ecu fuse

The ECU will not have anything to do with those issues. ECU or ECM is for "engine control module/unit". Sounds like you have a bad wire.

Oct 14, 2012 | 2003 Chevrolet Tahoe

1 Answer

89 camry ecu fuse location

Hi Welch, The ECU fuse is located under the bonnet (hood) in the fuse box there. Regards John

Aug 18, 2012 | Cars & Trucks

1 Answer

I keep hearing that I need to find and pull fuse 14 on my 96 subaru legacy 2.2L to try and reset the AT Oil Temp light that is flashing at start-up. The lid is missing, so I have no idea where this fuse...

Yes that is right:

Current trouble codes shown on the display are cleared by turning the ignition switch OFF after conducting self-diagnosis operation. Previous trouble codes, however, cannot be cleared since they are stored in the ECU memory which is operating on the back-up power supply. These trouble codes can be cleared by removing fuse 14 (located under the right lower portion of the instrument panel).

  • The No. 14 fuse is located in the line to the memory back-up power supply of the TCU and ECU (MPFI). Removal of this fuse clears the previous trouble codes stored in the TCU and ECU (MPFI) memory.
  • Be sure to remove the No. 14 fuse for at least the specified length of time. Otherwise, trouble codes may not be cleared.
When the Engine Control Module (ECM) , battery terminals, etc. are disconnected after memory is cleared, idling speed may increase. This is not considered a problem because the ISC Valve duty controlled learning value has been cleared. To return the engine to idling speed, idle for approximately 2 minutes with air conditioner "OFF".

Here is fuse #14 loc in panel Now its hard to see, but they go from the top left from 1 - 7 then it repeats for the next row 8 - 14. SO 14 is 2nd row from the top last one on right side.
118890618 118890619

Mar 09, 2011 | Subaru Legacy Cars & Trucks

1 Answer

Ecu/ecm relay

It is located behind your radio/heater control bezel.moz-screenshot-1.jpg Labor time to replace 1.4 hrs


Apr 26, 2009 | 2006 Hyundai Sonata

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

2,350 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts


Level 3 Expert

71231 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22059 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides