Question about 2002 Chevrolet TrailBlazer

1 Answer

Replacing license light bulbs on 2002 Chevy Trailblazer - How to?

I have unscrewed an removed the two lenses, but cannot remove the bulbs easily.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Just pull bulbs straight out be careful not to beak bulb

Posted on Feb 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace license plate light bulb for 2002 chevy trailblazer


Hello, If you look on the inside panel of the tailgate you'll see the lamp lens held in by 2 screws. Remove the 2 screws and then remove the lamp lens. Remove the bulb from the lens and install new bulb. Be sure to clean new bulb with clean cloth or paper towel to be sure there isn't any oil from your skin on the bulb. Replace lens assembly into tailgate. Reinstall 2 screws. Hope this helps. Good luck and God bless.

Jun 03, 2015 | Cars & Trucks

1 Answer

What holds the lights to the license plate?


Look up into the housing over the plate. You should see two glass lenses, and screws holding them in. Unscrew screws, remove bulbs, clean socket with contact cleaner and refit bulbs or new bulbs after cleaning glass lense and reflectors on the inside surfaces as dust and water will have entered and clogged it up over time.

Oct 13, 2014 | 1990 Nissan Pathfinder

1 Answer

License plate bulb needs replacing


Remove license plate. Unscrew the screws on the underside of the bumper. Slide the lights back toward the trunk and then down through the opening. Unscrew bulb and replace with a new one.

Reverse steps to reinstall the lights.

Feb 06, 2010 | 2003 Chevrolet Impala

1 Answer

My bottom brake lights dont work 2004 chevy trailbalzer


The recall on those was the boards the bulbs mount too. Remove the lenses and then the boards. See if your bulbs are good and check for fire at the light blue, or brown and white wire. Modle dependant. Good Luck

May 22, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

How do i replace the license plate bulbs on a 2002 chev trailblazer


There will be one or two screws or push pins securing the lense. Remove the screw or pin and pull the lense out. Twist the bulb socket and pull out the bulb. If you haven't already purchased the replacement bulbs, it will use a 194 bulb.

Apr 17, 2009 | 2002 Chevrolet TrailBlazer

2 Answers

Replacing license plate lights on Chevy Trailblazer


I just had the same problem. I took the cover off, saw the white bulb base, twisted it to take it out, but it popped back inside the door. I got it out, but it wouldn't pull through, so I twisted it back in place and went to Autozone to get new bulb. Once I saw the new bulb, it was obvious, just the bulb itself pulls out. There's so little room to work, I couldn't get it with just my fingers - - maybe rubber gloves would have worked, but I used pliers, lightly, wiggled it a little and it popped right out. I had a similar issue once with the taillight bulb and had to break the bulb and then grip the remaining filament wires with pliers to get it out, so that was my backup plan, just in case.

Hope this helps others.

Apr 14, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

License plate light replacement


The license plate lights are in the ledge above the license plate. 2 screws keep the lens cover in place. Remove the screws, and the cover comes off. Just pull the lamp out (wedge base) and replace.

Apr 13, 2009 | 2002 Chevrolet TrailBlazer

1 Answer

2002 license plate bulbs


its real simple look at the license plates then look up you will see 2 screw per lamp / unscrew them and slide remove its a 194 bulb so get some ready then replace and put back / Please rate my response thank you very much

Feb 01, 2009 | 2002 Toyota Avalon

1 Answer

Burned out license plate bulb


open trunk,

remove felt liner from rear of trunk, (liner directly behind rear lights in side trunk) should be 4 plastic Phillips head screws. Loosing screws, then slowly peel liner away. You will see 3 nuts on each side, removing these nuts will loosing the rear light lenses, so you can pull the lense away from the body from the out side to gain access to the license plate bulbs. Re-install in reverse order. While in there I would recommend replacing your brake light and reverse light bulb. Hey your already in there might as well do a little preventive maintance.

Dec 12, 2008 | 1995 Lexus ES 300

2 Answers

2002 trailblazer


All you have to do is find the "round rubber cover" on the back of the headlamp, pry it out with a flathead screwdriver and the lamp is right there.
To remove the headlamp assembly on a Trailblazer, remove the plastic panel that covers the hood latch assembly.
Take the cover for the air filter in order to get to the low beam cover.
Take the 3 screws out of the air filter cover and remove. You will then be able to get to the back of the low beam lamp. The high beam is reachable without this hassle.


Oct 07, 2008 | 2002 Chevrolet TrailBlazer

Not finding what you are looking for?
2002 Chevrolet TrailBlazer Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...