Question about 1994 Oldsmobile Cutlass Supreme

Open Question

Oil pan removal 1994 cutlass

Can I get the pan out without removing the transmission by un bolting the engine side of the K member. Tried earlier to pull the pan but it woul not clear the tranny and lower engine mount

Posted by on

4 Suggested Answers

  • 7 Answers

SOURCE: replacing oil pump in 95 Cutlass 3.1L

YOU WILL HAVE TO REMOVE THE EXHAUST PIPE IN THE REAR.IT HITS THE FLOOR PAN.ALSO REMOVE THE TWO DOG BONE MOUNTS ON TOP IF THIS ONE HAS THEM

Posted on Jan 03, 2009

  • 491 Answers

SOURCE: WHERE IS THE OIL PAN AND HOW HARD IS TO REMOVE

i suggest that if u dont know where the oil pan is to either take to a shop and have car repaired or have someone who knows cars assist u

Posted on Jun 06, 2009

drsinister69
  • 2317 Answers

SOURCE: Where are the starter bolts located? 1994 Olds Ciera S w/v6

Should be between the radiator and engine, underneath the car. There might be a plastic cover held on with 10mm bolts. The starter bolts go up thru the starter, into the block.

Posted on May 07, 2010

  • 610 Answers

SOURCE: need the torque setting for

3t40 trans 97 inch lbs,(16 bolts) 4t60 115 inch lbs.(19 bolts)

Posted on Jan 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove oil pan



4x4
1. Open the hood.
2. Disconnect the battery negative cables.
3. Remove the intake air assembly.
4. Remove the radiator shroud retaining bolts.
5. Install engine support fixture # 8534B .
6. Raise and support the vehicle.

WARNING: HOT OIL CAN CAUSE PERSONAL INJURY.


7. Drain the engine oil (Refer to 09 - Engine/Lubrication/OIL - Standard Procedure) .
8. Loosen the front engine mount bolts.
9. Lower the vehicle.
10. Use the engine support fixture # 8534B to raise engine out of the front mounts.
11. Remove the engine oil dipstick.
12. Raise and support the vehicle.
13. Remove oil pan bolts, break the pan to block seal, and lower pan slightly and remove oil suction tube fasteners.
14. Remove oil pan and suction tube.
15. Remove the 2 bolts from the front of the engine block stiffener.
16. Remove the oil pan.


4x2
1. Open the hood.
2. Remove the negative battery cables.
3. Raise and support the vehicle.
4. Remove the transmission oil cooler lines.
5. Remove the propeller shaft.
6. Remove the starter bolts.
7. Support the starter.
8. Remove the torque converter bolts.
9. Remove the exhaust hanger bolts.
10. Remove the gear shift cable.
11. Remove the wiring harness.
12. Remove the transmission mount.
13. Remove the crossover bolts.
14. Position the transmission jack.
15. Remove the bell housing bolts.
16. Remove the transmission.
17. Remove the flywheel housing bolts (8).
18. Remove the flex plate bolts (8).
19. Remove the engine oil dip stick.
20. Drain the oil.
21. Remove the steering rack bolts.
22. Remove the oil pan bolts.
23. Remove the oil pickup bolts.
24. Remove the oil pan. user_online.gif

Aug 01, 2014 | Dodge Ram 3500 Cars & Trucks

1 Answer

How to remove oil pan


Drain the oil, remove all but four pan bolts, loosen the remaining pan bolts until they're very loose, whack the sides of the pan with a large rubber mallet to dislodge the gasket. Remove the four remaining pan bolts, lower pan to the ground.

Be ready to do everything you need to do fairly quickly; don't let that engine stand open overnight, or it'll pick up dust & condensate inside.

Jul 29, 2014 | 1994 Oldsmobile Cutlass Supreme

2 Answers

HOW DO I REPLACE A SHIFT SILENOID IN A 1998 CHEVY VAN 1500


This is on a 4L60-E--Automatic Transmission

michael_cass_182.jpg
This is on a 4L80-E--Automatic Transmission


michael_cass_183.jpgHope this helps you ??

Jun 27, 2011 | 1998 Chevrolet Express

1 Answer

How to replace oil pan gasket


1994-96 VEHICLES
( see Figures 6 and 7 / click image for zoom )


zjlimited_1359.jpg

Fig. 6: Oil pan mounting bolt locations-1996 3.1L engine shown

zjlimited_1360.jpg

Fig. 7: Oil pan sealant application points-1996 3.1L engine shown

  1. Disconnect the negative battery cable.
It may be necessary to remove the hood, with the help of an assistant, for access.
  1. Remove the engine mount strut and A/C compressor (if equipped) and the engine mount strut bracket assemblies.
  2. Remove the electric cooling fan assemblies. -28467 and J 26462, or equivalent.
  3. Raise and safely support the vehicle. Drain the engine oil.
  4. Remove the front exhaust manifold pipe.
  5. Remove the intermediate shaft bolt/screw.
  6. Remove the oil level sensor.
  7. Remove the engine splash shield.
  8. Suitable support the drivetrain and front suspension with jack stands.
  9. Remove the transaxle mount side frame retaining nuts from the drivetrain and suspension frame assembly.
  10. Remove the engine mount side frame nuts from the drivetrain and suspension frame assembly.
  11. Unfasten the rear drivetrain and front suspension frame bolts/screws.
  12. If equipped, remove the lower drivetrain and front suspension frame bolts/screws.
  13. Remove the engine mount assembly.
  14. Remove the flywheel inspection cover.
  15. Remove the starter.
  16. Disconnect the transaxle mount assembly from the oil pan.
  17. Unfasten the side bolts and screws and the retaining bolts and screws, then remove the oil pan. Remove and discard the oil pan gasket.
To install:
  1. Clean the gasket mating surfaces.
  2. Apply a small amount of sealer on either side of the rear main bearing cap, where the seal surface on the cap meets the cylinder block. Install a new gasket on the oil pan.
  3. Position the oil pan and secure with the retaining bolts and screws. Tighten the retaining bolts and screws to 18 ft. lbs. (25 Nm) and the side bolts/screws using tool J 39505 or equivalent.
  4. Fasten the transaxle mount assembly to the oil pan.
  5. Install the starter motor.
  6. Install the flywheel inspection cover.
  7. Install the engine mount assembly.
  8. Carefully raise the drivetrain and front suspension assembly. Install the rear drivetrain and front suspension frame bolts/screws.
  9. Fasten the engine mount frame side nuts to the drivetrain and front suspension frame assembly. Install the transaxle mount frame side nuts to the drivetrain and suspension frame assembly.
  10. Remove the jackstands from the drivetrain and front suspension frame assembly.
  11. Install the engine splash shield and the oil level sensor.
  12. Install the intermediate steering shaft bolt/screw. Connect the front exhaust manifold pipe.
  13. Carefully lower the vehicle.
  14. Remove the engine support tools.
  15. Install the electric cooling fan assemblies.
  16. Install the engine mount strut and A/C compressor, bracket and the engine mount strut bracket.
  17. If removed, install the hood assembly.
  18. Fill the crankcase to the correct level. Connect the negative battery cable. Run the engine to normal operating temperature and check for leaks.
Hope this helps (remember to rate this answer).

Jun 04, 2011 | 1994 Oldsmobile Cutlass Supreme

1 Answer

On 1994 dodge 1500 4x4 to change oil pan do i have to raise the engine


  1. Disconnect the negative cable from the battery.
  2. Remove engine oil dipstick.
  3. Raise vehicle.
  4. Drain engine oil.
  5. Remove exhaust
  6. Remove left engine to transmission strut.
  7. Loosen the right side engine support bracket cushion thru-bolt nut and raise the engine slightly. Remove oil pan by sliding backward and out.
  8. Remove the one-piece gasket.

Oct 15, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

I need to change engine oil where is the drain


most engine oil drain bungs are at the bottom of the engine ,but latly most car companys have done away with the system and replaced it with the oil retieve system which means the oil dip stick is removed and a vacuim pump is placed onto it and takes the oil out in seconds through the the did stick im not sure if your engine has this system or not.adrian,,,,,,,,,,,,

Aug 14, 2010 | 1997 Oldsmobile Cutlass Supreme

1 Answer

Oil pan leak on 1994 bronco with a 5.0 liter


Oil Pan Removal
  1. Remove the bolts attaching the fan shroud (8146) to the radiator (8005) and position the fan shroud over the fan assembly.
  2. Raise vehicle.
  3. Remove exhaust manifold-to-exhaust pipe.
  4. Disconnect the oil cooler line at the left side of the radiator if equipped with an automatic transmission (7003).
  5. Remove the nuts and lockwashers attaching the engine support insulators to the chassis bracket.
  6. Drain the crankcase.
  7. Loosen transmission mounting nuts.
  8. Raise the engine (6007) and place wood blocks securely under the engine supports.
  9. Remove the oil pan attaching bolts and lower the oil pan (6675) onto the crossmember.
  10. Remove the oil pan from the vehicle.

Apr 07, 2010 | 1994 Ford Bronco

2 Answers

How you take out the oil pan on 1990 ford bronco 4x4 302 5.0


Ford Pick-ups and Broncos 1987-1996 Repair Guide
Fuel Injected 5.0L and 5.8L Engines - Oil Pan
  1. Drain the cooling system.
CAUTION When draining the coolant, keep in mind that cats and dogs are attracted by ethylene glycol antifreeze and are quite likely to drink any that is left in an uncovered container or in puddles on the ground. This will prove fatal in sufficient quantity. Always drain the coolant into a sealable container. Coolant should be reused unless it is contaminated or several years old.
  1. Remove the bolts attaching the fan shroud to the radiator and position the shroud over the fan.
  2. Remove the upper intake manifold and throttle body (see ).
  3. Remove the nuts and lockwashers attaching the engine support insulators to the chassis bracket.
  4. If equipped with an automatic transmission, disconnect the oil cooler line at the left side of the radiator.
  5. Remove the exhaust system.
  6. Raise the engine and place wood blocks under the engine supports.
  7. Drain the crankcase.
CAUTION The EPA warns that prolonged contact with used engine oil may cause a number of skin disorders, including cancer! You should make every effort to minimize your exposure to used engine oil. Protective gloves should be worn when changing the oil. Wash your hands and any other exposed skin areas as soon as possible after exposure to used engine oil. Soap and water, or waterless hand cleaner should be used.
  1. Support the transmission with a floor jack and remove the transmission crossmember.
  2. Remove the oil pan attaching bolts and lower the oil pan onto the crossmember.
  3. Remove the two bolts attaching the oil pump pickup tube to the oil pump. Remove the nut attaching the oil pump pickup tube to the No. 3 main bearing cap stud. Lower the pickup tube and screen into the oil pan.
  4. Remove the oil pan from the vehicle.
To install:
  1. Clean the oil pan, inlet tube and gasket surfaces. Inspect the gasket sealing surface for damages and distortion due to overtightening of the bolts. Repair and straighten as required.
  2. Position a new oil pan gasket and seal to the cylinder block.
  3. Position the oil pick-up tube and screen to the oil pump and install the lower attaching bolt and gasket loosely. Install nut attaching to number 3 main bearing cap stud.
  4. Place the oil pan on the crossmember. Install the upper pick-up tube bolt. Tighten the pick-up tube bolts.
  5. Position the oil pan to the cylinder block and install the attaching bolts. Tighten to 10-12 ft. lbs. (13-16 Nm).
  6. Install the transmission crossmember.
  7. Raise the engine and remove the blocks under the engine supports. Bolt the engine to the supports.
  8. Install the exhaust system.
  9. If equipped with an automatic transmission, connect the oil cooler line at the left side of the radiator.
  10. Install the nuts and lockwashers attaching the engine support insulators to the chassis bracket.
  11. Install the upper intake manifold and throttle body (see ).
  12. Install the fan shroud.
  13. Fill the crankcase.
  14. Fill and bleed the cooling system.

If you need see images about this theme, can visit autozone.com (free register).

Hope helped (remember rated this help) Good luck.

Dec 02, 2009 | 1990 Ford Bronco

2 Answers

How to change oil pump


drain oil and filter remove.
Drop oil pan under engine.
Un bolt oil pump and re install new pump fill new oil and filter and gasket , cap , start engine test for leaks shut down re check oil level.
Vitally

Sep 10, 2009 | 1998 Oldsmobile Cutlass

Not finding what you are looking for?
1994 Oldsmobile Cutlass Supreme Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...