Question about 1993 Jeep Wrangler

1 Answer

93 wrangler yj electrical wet

I have a 1993 jeep wrangler yj with 4 cylinder 2.5l and i got it stuck in a creek and spun the tires and flung water into motor and shut down... i turned key and fuel pump runs, gauges turn on and i try and the starter relay ''clicks''.. bought new relay.. nothing.. so i took out plug, layed under it and crossed starter and no spark. took off dist. cap and sprayed in WD40 and still nothing!?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

You have likely fixed this by now but if not, you will have to use some dry rags and dry off everything!!!! Use compressed air wherever you can't get to (or at the least, a tire pump) Vehicles are not designed for use in the water. If ;you want to do this, get with some off road clubs that can give you tips on waterproofing stuff!!! Just to somewhat "wheatherise" my stuff, I wipe down ignition components with a rag saturated with wd40&silicone spray. I don't think this will work in deep water but it sure helps in very damp or rainy weather! You can also make splash guards out of very heavy tar paper or sheet metal that you can place under the front, but be careful where and how you place and secure it so nothing interferes with steering etc.

Posted on Feb 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

On my 1993 wrangler with a 2 5 if i try to start it it only fires on cylinder 1 and 3 if i shut it off and try again it fires only on 2 and 4 what would cause this


Sounds like a spark plug or distributor problem.... Change out all your spark plugs and check your wires for breaks. Check fuel injectors for build-up.

Feb 06, 2016 | 1993 Jeep Wrangler

1 Answer

Diagrams firing order


4 cylinder
all are 1,3,4,2 (non boxer engines)

here it is , FSM
93 is here.
YJ
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service


you pulled the dizzy cap wires willy nilly
you need dizzy rotor direction too.
RTM

Jul 21, 2014 | 1992 Jeep Wrangler

1 Answer

Reasymble 1993 jeep wrag collumnngler steerin


ah.
how to reassemble the 93 jeep wrangler steering column?
someone else took it a part?
read the FSM. free.
YJ JEEP
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

Feb 17, 2014 | 1993 Jeep Wrangler

1 Answer

1990 Wrangler: I have a 1990 yj with the 4.2, my question for eve...


Most 90 wranglers from 89 to 95 have an ax15 5 speed transmission in them. The 4 cylinders had an ax5 transmission.

May 17, 2010 | 1990 Jeep Wrangler

2 Answers

I had a fire in the engine of my 93 yj 4 cyl i need to replace the engine wiring harness can it be replaced with the wiring harness from jeeps of other years


I would really try to get the same year and motor as you have. There is some much that often changes from year to year, and engine to engine.

Mar 16, 2010 | 1993 Jeep Wrangler

1 Answer

1995 Jeep YJ with a new engine. No power going to coils.


sounds like you are working on a car FSM free?
why do that?
95 YJ
early wrangler
i have 95 yj fsm and 93, the 93-95 are a year class range.
very simular.
here is a free 93 fsm with full schematics in chapter 8w
wiring chapter, clik
pdf 76 is page YJ 19 actual
and as you can see its cave man simple 2 wires.
minus to ECU ignitor driver. transistor (inside ecu)
and
+ goes to
a142 sheet 5 (pdf 62)

im not sure what part A<B<C is, a fuseable link, is my guess
and is blown. but that be a bingo spot for sure.
the full manual is there.
see spark chapter.
http://www.jeep4x4center.com/knowledge-base/index.htm?utm_source=cj#service

posted over 100 times, this link, its not new.

Feb 13, 2010 | 1995 Jeep Wrangler

1 Answer

Soft top-1993 Jeep Wrangler YJ


OK I have a yj and you start from the windshield put the snaps/or what ever yours is on the top of the doors then down the side or the doors then under the back side window then around the curve and this is the hardest part then your tailgate also make sure your bars on the inside are loseuntil the top is on then thighting those bars and you should have a nice tight top but belive me it is hard and you might need a flathead screw driver for the corners. Good luck and a jeep wave to you!

Apr 03, 2009 | 1993 Jeep Wrangler

2 Answers

1993 Wrangler 4.0 Randomly My clutch pedal will not go in.


I can't remember if that year has a clutch master cylinder or not. Check to see if it does, it will be next to the brake master cylinder, and look like a single round silver dollar sized vesle. To the left of your brake master cylinder. check if its bone dry, if so refill it.

if this is not the case and it does not have a master cylinder, you need to check your clutch out.

Dec 03, 2008 | 1991 Jeep Wrangler

Not finding what you are looking for?
1993 Jeep Wrangler Logo

207 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...