Question about 1999 Dodge Ram

Open Question

Engine code 522 dodge ram 4.7 engine

Getting this code. manual says it is low voltage to the oil pressure sending unit. How do I repair this? Does this mean that the sensor is bad?
I've just changed the camshaft sensor 2 days ago for a code that came up for that could this be related issues?

Posted by on

  • 1 more comment 
  • pastulov Feb 18, 2009

    I believe it is PO522 I got this code from turning the ignition 3 times and got that code. Checked in the Haynes manual and that is what it told me. Low Voltage to oil pressure sensor.

  • pastulov Feb 18, 2009

    I should clarify that it is a 2003 dodge ram quad cab automatic 4x4 with a 4.7

  • yadayada
    yadayada May 11, 2010

    522 is not a code, is this P0522 a OBD 2 code?



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Oil pressure light comes on every now and again 1995 dodge ram van b2500 5.9l non turbo

The only way to know if you need engine repair or you have a bad sender is to hook up an oil pressure test gage to the sender port and manually check the pressure. You will need the deep oil pressure sending unit removal tool to get the sender out (I did this).

Nov 09, 2016 | 1995 Dodge Ram 2500

1 Answer

While driving gas pedal stops working 2007 dodge 1500 5.7 turn engine off then wont start

engine oil pressure to low posible bad oil pressure sending unit o engine internal proble o no oil on engine or electrical problem

Sep 25, 2014 | 2007 Dodge Ram Truck

1 Answer

I have a 2003 dodge neon 2.0l 16v engine that cranks over but will not start any ideas?

P0108 (M) MAP Sensor Voltage Too High, P0118 (M) ECT Sensor Voltage Too High Engine coolant temperture sensor input above the
maximum acceptable voltage, P0123 (M) Throttle Positon Sensor Voltage High Throttle position sensor input above the maximum
acceptable voltage range, P0522 Oil Pressure Sensor Low Oil pressure sensor input below acceptable voltage. Sounds like you have an electrical problem, either computer failure or bad sensors. It's hard to believe that you gained so many sensors just from replacing the cylinder head. Disconnect your battery for one minute, then reconnect. Try driving it down the road.

Aug 11, 2014 | 2003 Dodge Neon

1 Answer

Dodge 1500 wont start codes p422 - p522

cranks ok but wont start and battery is charged to 12.6v dc rested?>
and wont jumper cable start>>>>>>??????????????????????
which engine>?
start with gas cap off?
2 problems, if wont start cap off.
tank vent system issues,
522 is the one.
P0522 Dodge - Engine Oil Pressure Sensor/Switch Circuit Low Voltage

the PCM sees no oil pressure and refused to start.
sounds like a winner there. huh.?

ok, so check oil pressure.
if good , then the switch is bad, or wires to it bad, fell off.
Sig: I must ask questions first, I'm blind, and my tools can't reach, dig?

Jun 22, 2014 | 1999 Dodge Ram

1 Answer

Code po 522,on my dodge 2004 caravan how do I fix it.

well it means that you have low voltage to your oil pressure sending unit, try to add oil, only after checking to see if there is the correct amount, has the oil light come on?

Aug 13, 2013 | 2005 Dodge Ram 1500

1 Answer

Will a faulty oil pressure sensor shut the truck down/2007 dodge ram 2500 5.7 hemi

Yes,here it is.

Nov 17, 2012 | Dodge Ram 2500 Cars & Trucks

1 Answer

I have a 2001 Dodge Ram 1500 When Im driving for awhile the check gauges light comes on and oil gauge come down

You either have good oil pressure and a bad oil pressure sending unit, or your oil pressure really is low. Get it checked out, so you don'y destroy the engine.

Apr 28, 2011 | Dodge Ram 1500 Cars & Trucks

1 Answer

What causes P0533 & P0532 trouble codes on 2006 Dodge 2500 SLT air conditioner. The codes are for too high of voltage & too low of voltage for the A/C sending unit. So my compressor pump clutch...

P0533 A/C Pressure Sensor High.

It could be low on refrigerant, or it could be a bad sensor. Back-probe the pressure sensor connector (on the discharge line, near the compressor - it's a 4-way connector) on the dark blue wire with the engine running and the A/C turned to max. If you get no volts, or 5 volts, the sensor is bad. 4.5 volts indicates a properly-operating system, while less than 4.5 indicates low pressure, and anything above indicates high pressure. If low or high pressure is suspected, verify with a set of refrigerant gauges.

If warranted, the sensor can just unscrew. You won't lose refrigerant - there's a valve built in to the line to prevent that. Make sure to use a new O-ring and lube it with the proper oil if you do change the sensor.
Add a comment

Jul 08, 2010 | 2006 Dodge Ram 2500

1 Answer

I got this code from turning the ignition 3 times p-0522 we have also notice oil light comes on. if it is low voltage to oil pressure what do i need to get it fix

If the oil level is good and you are getting low voltage on the oil sensor replace the oil pressure sensor. The last chrysler I saw that code on the code indicated a bad O2 sensor. If you need to know for sure get the Haynes repair manual on your vehicle from the local auto parts store, it has a listing of the codes and what needs to be repaired when you get them.

Oct 12, 2009 | 1999 Dodge Ram

2 Answers

1989 dodge ram 150 4/w drive pickup has no oil pressure showing on the gage, driving or sitting still.

You need to have a oil pressure guage hooked up to see if you have a bad guage, sending unit to the guage, or if your oil pressure is actually low. Any garage should be able to do this, if you can't get one.

Aug 03, 2009 | 1989 Dodge Ram D-Series Pickups

Not finding what you are looking for?
1999 Dodge Ram Logo

1,134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides