Question about 1995 Chrysler Concorde

Open Question

Headlights blinking 95 concorde - recently replaced powertrain control module. Now when any door is opened, the headlights start flashing. Initial trace found that the headlamp delay relay was clicking. Remove relay and lights stop flashing. However, removing relay also kills instrument panel lamps. Currently have entire dash broken down and open. Have checked the body control module, headlight switch and connectors, headlamp dimmer switch, all door switches. No problems or defects (i.e. shorts or breaks) in items checked. Problem still exists. Any suggestions on what to check next. I have been able to identify the connector circuits involved at the body control module and the primary fuse/ juction box all the way down to the individual wire to disconnect to make the problem go away. However, I cannot leave the circuit disconnected. Any help in diagnosing where to go from here would be appreciated.

Posted by on

  • yadayada
    yadayada May 11, 2010

    Would suggest u try premium chat.



6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: 2000 chrysler concorde switch unlocks but wont lock doors.

sounds like the actuator. I had the same problem. Mine got to the point where it will now only work with the key. Had it looked at by dealer.. actuator is bad. Good luck.

Posted on Apr 28, 2009

  • 153 Answers

SOURCE: where is the OBDI connector for a 1995 concorde

under sterring whee,l right side, up underdash near centerconsole/radio area

Posted on Oct 07, 2009

  • 1757 Answers

SOURCE: Need to remove the Headlamp/dash light

I have a 2002.
After making sure you remove all visible screws, these panel snap off and snap back on. Any resistance, re-look in that area for a missed screw(s).
Restated: Once all screws have been removed, pull out the panels. It is a lot easier that it looks.
Start with the lower steering column. Look from underneath with a flashlight. You will see the screws and screw holes. The lower "kick" panel (driver side) screws can be seen by looking underneath it.
Other than a screw driver, no "special tools" are needed.
Let me know if this helped, or if you have additional information or questions. Feel free to contact me at!

Posted on Feb 11, 2010

Testimonial: "Thanks for your time. I don't normally work on cars, but work with electrical all the time. Finding out how to "get in" to the part was very helpful"

  • 1 Answer

SOURCE: instrument panel lights don't work

please advice, have you solved the problem? I have the same one on my Sebring. Many thanks.

Posted on Apr 06, 2010

  • 2926 Answers

SOURCE: I have a pt cruiser, the instrument panel has

The PCM is not a computer chip, it is the Powertrain Control module (engine computer). What needs to be done is a code reader needs to be connected to the diagnostic link of the vehicle, and checked for fault codes relating to this condition. I'm not sure how it was checked initially, but what I can tell you is if the PCM is found to be the issue, your not going to be able to repair it yourself. An expensive scan tool is needed to program the PCM when it is replaced, and is not available to the average person or technician. A Chrysler dealer will be the best option. It may also be related to the BCM (Body control module) since this problem seems to be related to the interior lights also.

Posted on Dec 09, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Por favor, necesito diagrama de caja de fusibles para Mazda B2300 del 2001

Mazda B-Series (2001) - fuse box diagram Year of production: 2001

Interior fuse panel

Mazda B-Series - fuse box -
interior fuse panel Number Ampere rating [A] Description 1 5 Power Mirror 2 10 Blower Motor Relay, Air Bag Diagnostic Monitor, Passive Deactivation (PAD) Module 3 7,5 Trailer Tow Connector (LH Stop/Turn) 5 10 4×4 Control Module 7 7,5 Trailer Tow Connector (LH Stop/Turn) 9 7,5 Stoplamp Switch 10 7,5 Cruise Control Servo/Amplifier Assy., GEM/CTM, Shift Lock Actuator, Blend Door Actuator, A/C Heater Control Assy., Turn Signals 11 7,5 Instrument Cluster, Main Light Switch, RABS Resistor 13 20 Brake Pedal Position Switch 14 20 RABS Module 10 4WABS Mod., 4WABS Main Relay 16 30 W/W Motor, Wiper Hi-Lo Relay, Wiper Run/Park Relay, Washer Pump Relay 17 25 Cigar Lighter, Data Link Connector (DLC) 19 25 PCM Power Diode, Ignition, PATS 20 7,5 GEM/CTM, Radio 21 20 Flasher 22 20 Auxiliary Power Point 24 7,5 Clutch Pedal Position (CPP) Switch, Starter Interrupt Relay 26 10 Battery Saver Relay, 4×4 Electronic Shift Relay, Interior Lamp Relay, 4×4 Elec. Shift Control Module, Dome/Map Lamp, Instrument Illumination Dimming Module, Restraint Control Module, GEM/CTM, Instrument Cluster 28 7,5 GEM/CTM System, Radio 29 15 Radio 33 15 Headlights, DRL Module, Instrument Cluster 35 15 ISA Horn Relay if not Equipped with Truck Security Module

Engine compartment fuse block

Mazda B-Series - fuse box -
engine compartment Number Ampere rating [A] Description 1 50 I/P Fuse Panel 6 50 ABS Pump Motor 7 30 Powertrain Control Module 8 20 Power Door Locks and Remote Entry 11 50 Starter Relay Ignition Switch 12 10 PCM Memory 13 20 4×4 Motor 16 40 Blower Motor 21 10 PCM Memory 23 20 Fuel Pump Motor 24 30 Headlights 25 10 A/C Clurtch 28 30 4WABS Module 30 15 Trailer Tow 31 20 Fog Lamps, Day Time Running Lamps (DRL) 33 15 Park Lamp 38 10 Left Headlamp Low Beam 41 - Heated Oxygen Sensors 42 10 Right Headlamp Low Beam 45A - Wiper High/Low 45B - Wiper Park/Run 46A 46B - Front Washer Pump 47A 48A - Fog Lamp 48B - Fog Lamp Relay 49 - Full Starter 50A 50B - Fuel Pump 53 - Powertrain Control Module (PCM) Diode 54 - Powertrain Control Module (PCM) Diode 55 - Blower 56A - A/C Clutch Solenoid 56B - Trailer Tow

Jul 04, 2017 | Mazda Cars & Trucks

1 Answer

My 2005 durango lights continusly flashing headlights fuses are all good as soon as you open the door they start flashing

First take your steering column cover off and look for a broken or loose wire, If not, sadly it is probably your "body control module" has gone bad, sad because there around $300.00 new to replace! Pray it's a broken or loose wire, this happens with tilt steering! Good Luck!!!

Oct 30, 2016 | Cars & Trucks

1 Answer

Po601 code comes in with reader chevy Colorado starts and dies

Possible causes
- Faulty Powertrain Control Module (PCM)
- Powertrain Control Module (PCM) harness is open or shorted
- Powertrain Control Module (PCM) cicuit poor electricl connection
- Low battery voltage

Jan 05, 2015 | Cars & Trucks

1 Answer

1998 chrysler concorde code P1684 P0122

P01684 just says that the battery has been disconnected within the past 50 starts. If you have already replaced the TPS and still get the P0122 code, it could be a short in the wiring or a problem with your Powertrain Control Module. Other names for the PCM is ECM and ECU. Engine Control Module and Engine Control Unit

Mar 02, 2013 | 1999 Chrysler Concorde

1 Answer

Engine light is on code coming up p0601

This code indicates an error or fault in the powertrain control module memory. A common procedure known as memory flashing is performed at the dealer. The vehicle's computer (powertrain control module) memory is erased, then replaced with an updated version of the previous driveability program. If the powertrain control module doesn't store the program, then a replacement module would be the next likely service.

Sep 09, 2011 | 2002 Chrysler Town & Country

2 Answers

What causes a p 0327 diagnostic code on a 95 contour

P0327 - Knock Sensor 1 Circuit Low Input Bank 1 or Single Sensor
First check the knock sensor connector. If the connector is clean and secure, replacing the knock sensor usually takes care of the problem.

- An excessively low voltage from the sensor is sent to Powertrain Control Module (ECM) or Engine Control Module (ECM)

The knock sensor is attached to the cylinder block. It senses engine knocking using a piezoelectric element. A knocking vibration from the cylinder block is sensed as vibrational pressure. This pressure is converted into a voltage signal and sent to the Powertrain Control Module (PCM) or Engine Control Module (ECM).

- Engine Light ON (or Service Engine Soon Warning Light)
- Lack/Loss of Power

Possible causes
- Knock sensor circuit short to GND.
- Knock sensor circuit short to PWR.
- Knock sensor circuit open.
- Damaged knock sensor.
- Faulty Powertrain Control Module (PCM) or Engine Control Module (ECM).

Test and check it. Hope helps.

May 12, 2011 | 1995 Ford Contour

1 Answer

I have a 2004 cadillac deville dhs has 12,000 miles on it was driving and the lights on started chiming and blinking and emergency flasher lights come on and blink hit the flasher button no help got a few...

DTC B2507
Seat Temperature and Mode Signal
DTC B1860
Driver Lumbar Vert Sensor CKT Malf
DTC C1295
Brake Lamp Switch Circuit Open
DTC C0665
Chassis Pitch Signal Circuit
DTC U1000 and U1255
Class 2 Communication Malfunction
DTC U1001-U1254
Lost Communications With ***
Circuit Description
Modules connected to the class 2 serial data circuit monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. When a module receives a message for a critical operating parameter, the module records the identification number of the module which sent the message. These node alive messages are used for State of Health monitoring. A critical operating parameter is one which, when not received, requires that the module use a default value for that parameter. When a module does not associate an identification number with at least one critical parameter within 5 seconds of beginning serial data communication, DTC U1000 or U1255 is set. When more than one critical parameter does not have an identification number associated with it, the DTC will only be reported once. The following modules communicate on the class 2 serial data circuit:
• Audio amplifier
• Cellular telephone module w/UV8
• Dash integration module (DIM)
• Digital radio receiver
• Driver door module (DDM)
• Driver door switch assembly (DDSA)
• Electronic brake control module (EBCM)
• Electronic suspension control module (ESC)
• Front passenger door module (FPDM)
• Inflatable restraint sensing and diagnostic module (SDM)
• Instrument panel cluster (IPC)
• Instrument panel integration module (IPM)
• HVAC control module - auxiliary
• Left middle door module (LMDM) w/V4U
• Left rear door module (LRDM)
• Memory seat module (MSM) w/A45
• Powertrain control module (PCM)
• Radio
• Rear integration module (RIM)
• Remote control door lock receiver (RCDLR)
• Right middle door module (RMDM) w/V4U
• Right rear door module (RRDM)
• Steering column module w/N37
• Theft deterrent control module
• Window switch - passenger front w/armored car
• Vehicle communication interface module (VCIM)
Your best bet ,take your vehicle to a qualified repair shop.

Nov 17, 2017 | 2004 Cadillac Deville

1 Answer

I got a p0700 code which is trans control system on my wifes 97 Concorde. What does it mean.

this is the TCM (transmission control module) telling the PCM (powertrain control module) to turn on the check engine light due to a fault in the auto trans, the code for the fault is stored in the TCM, to get this cheched you need to have the dealer run a TCM fault code test.

May 13, 2010 | 1997 Chrysler Concorde

2 Answers

Interior Lights Flash On and Off By Themselves

Pull one door sensor at a time and test. They get compressed too far and eventually no longer open the circuit. If you find a switch compressed too far, just replace it...

Door switches are self adjusting, to allow for differences in jamb tolerance... Start with driver's door.

Sep 25, 2009 | 2001 Chrysler Concorde

1 Answer

1993 chrysler instrument cluster lights out, headlights flash

sounds like you have a problem with your alarm system. likely the ignition switch is the problem.

May 15, 2017 | 1993 Chrysler Concorde

Not finding what you are looking for?
1995 Chrysler Concorde Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides