Question about 2003 Ford F350 Super Duty DRW SuperCab

1 Answer

How to remove fan schroud w/6.0 D engine - 2003 Ford F350 Super Duty DRW SuperCab

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

Screws around rad 6 or 8 of them

Posted on Feb 18, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Car make noise when step gas

might be motor mount and fan hitting the schroud..

Apr 02, 2014 | 1998 Chevrolet Monte Carlo

1 Answer

Cooling fan relay location

should be right on the fan,fan schroud, or in that area.check u r owners manuel if u hav 1.

Apr 21, 2013 | 1988 Mercury Topaz 2 Door

2 Answers

Does the fan and fan schroud need to come off to replace the radiator


Hold the fan clutch steady with a fan clutch wrench and disconnect the fan using a fan hub wrench. Notice the fan remains held in the engine compartment by the fan shroud...

Remove the two bolts securing the fan shroud to the radiator, with a ratchet and socket. Pull the fan shroud and fan blade assembly from the engine compartment.

Jul 21, 2011 | 1997 Mercury Mountaineer

1 Answer

My 1998 chevy caviler has a grinding noise when i step on the gas peddle & rev it up, what can this be?

this could be anything i assume your hearing it under the hood. with the engen OFF pop open the hood and see if the fan blades are rubbibg aginst the fann schroud. check the end of each fan blade for possable signs of rubbibg check around the schroud for rubbing or anysign of rubbing. i dont know what type of noise your hearing you might want to check the belts make sure they are in place. and the pullys to make sure there is no movement other than turning the way they are supposed to go. if you cant see anything have a friend over and being very carefull with the hood still up have them or you start the car while the other one watches and listens under the hood. [KEEP HANDS BACK] have them rev... a little on it to see whats making the noise. and im sure youll find it. remember it has to be a moveing part making the noise..i hope this helps

Jun 04, 2011 | 1998 Chevrolet Cavalier

2 Answers

How to remove the fan clutch

To remove fan clutch, you need a special clutch fan tool. Sometimes i can remove it with a large adjustable wrench while locking the water pump pulley. Remember to turn counter-clockwise.

Feb 18, 2011 | 1996 Ford Explorer

1 Answer

Need to replace water pump. how easy it it?

Pretty easy. Just drain antifreeze. Then loosen 4 bolts that holds fan to pulley. Remove plastic fan schroud and fan pulley. Loosen water pump bolts in criss cross pattern and remove water pump. Clean surface install new gasket and water pump install in reverse order. Tighten in staggerd order to keep from breaking and warping. Don't forget to change thermostat good time to replace. Part should be about 50 bucs at your local parts store.

May 02, 2010 | 1999 GMC Yukon

2 Answers

I need to find out the timing specs for my 1992- S10 P/U 4.3L The engine dies when I let my foot off the gas. I have been told it's on a sticker on my fan schroud... the "sticker" is gone. Can you help?

there is a wire on most s10s that is below the heater box under the carpet. it is a single wire and is tan with a black stripe.unplug at the you can check the timing. it should be 0 tdc

Mar 23, 2010 | 1992 Chevrolet S-10

1 Answer

Where is the hook up located for the wind shield washer

on the side of the fan schroud pass side just below where you fill it with washer fluid

Mar 09, 2010 | 2001 Dodge Durango

1 Answer

Fan is wabling on a 1997 jeep, the belt is still on for now, we can't start the jeep up because it hit the schroud.

Now its a couple of things that may be wrong...1 is your waterpump may be bad, and the shaft is wobbling back and forth...2. it could be your fan clutch...or 3. it just maybe the fan blade itself..sometimes they wear out, because they are made up of plastic...however you can easliy see that, and move it around..and make sure all the bolts are tight..

So. check the waterpump, by tring to shake the fan up and down and side to side, and see if the shaft move, then its the waterpump...the clutch really wont give you too much play, it just wont spin as fast, with the engine running, Or the blade..basically it will look like its fallen off....

Jan 19, 2010 | 1997 Jeep Cherokee

1 Answer

1999 dodge ram, how to remove fan and pulley from water pump

The clutch fan assembly unscrews from the water pump with a special tool that can be rented or purchased from local autoparts stores. If the assembly is left hand threads is should be indicated on the plastic fan schroud (cover).

Jun 08, 2009 | 1999 GMC Jimmy

Not finding what you are looking for?
2003 Ford F350 Super Duty DRW SuperCab Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

77939 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

5651 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides