Question about 1998 Nissan Altima

1 Answer

No firing to distributor

The smaller plug to distributor crank sensor side no signal everything else working change crank sensor same thing

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 32 Answers

If you have done that it could mean 1 other thing your engine computer

Posted on Apr 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

What would cause a 97 chevy 1500 with a 4.3L not to have spark coming out of the distributor any ideas


Don't know if this will help you or not. But we found out with our 97 Silverado, that almost everything electrical went through the ignition switch. You might investigate an ignition problem.

May 27, 2014 | 1997 Chevrolet K1500

2 Answers

1990 nisan n13 motor 1.6, has no spark to coil i drove car to train station, when i got back the car would not start, replaced coil, distributor, ecu box, all fuesible links, plugs & plug leads, fuel...


Your car has both a crank and cam position sensor. First start with your crankshaft position sensor. It is located by the harmonic balancer on the front of the motor.

Nov 28, 2013 | 1990 Nissan Pulsar

1 Answer

2003 trailblazer 5.3 no fire change cam & crank sensor


if its got no fire and you changed your cam and crank sensor try replacing the ignition Coil then if it doesn't work replace the distributor cap and spark plugs and wires if that doesn't work then take the distributor cap off and replace the distributor Rotor if it still doesn't work replace the wires to the rotor if still i dosent work check your fuses but i assure you that should fix it.

Feb 24, 2012 | 2004 Chevrolet TrailBlazer

2 Answers

My 02 chevy cavalier turns over but will not start. I have replaced ever thing i know that could be wrong.


does it produce fire does the gas pressure rise does the crank sensor and cam sensor work

Feb 09, 2011 | Chevrolet Cavalier Cars & Trucks

3 Answers

I have a 96 chrysler sebring V6 2.5 coupe. Car will crank but won't start. Fuel is no problem. Timing belt ok. I have no spark or fire. Computer coded pcm or distributor. I changed the computer but the pcm...


What does the distributor cap look like. Are the prongs inside all green. Does the rotor look burnt.If chrysler says the pcm is compatable then it should be fine.

Jan 07, 2011 | Chrysler Sebring Cars & Trucks

1 Answer

Vehicle cranks but won't fire. This problem came on all of a sudden. It was running fine up until it wouldn't start.


4 important things for a no start to check.Power from the ignition switch.Power at the fuel pump relay.Fuel pressure,spark at the plugs and a signal leaving the crankshaft sensor {distributor}. etc

Oct 12, 2010 | 1998 Oldsmobile Bravada

3 Answers

No spark installed new coil and had mogel for the distibutor checked


Check fuses relays and ground wires. The check inside the distributor cap and make sure the piece the rotor inside distributor is clean of oil and the area below hall effect is dry and without oil.The piece down below is also a item that can effect it from firing.it is a magneto and it controls the firing and fuel by sending signals to the ecm. If you check the above without finding an issue the best thing to do is see if you can borrow a scan tool to get any codes that could be helpful with diagnosing. Im sorry if this isnt exact help but it is trail and elimination that fixes issues like this instead of just replaceing parts.

Oct 03, 2009 | 1995 Ford Taurus

2 Answers

No spark


The crank sensor is a common problem with these jeeps.
The sensor is on the top side of tranny bell housing on the drivers side.

Dec 09, 2008 | 1989 Jeep Cherokee

3 Answers

1999 Chevy tahoe will not start


check the crank sensor. no signal from the crank sensor causes a no spark condition. best way to check is to put a scanner on and check for rpms.
the crank sensor is differnt from the cam sensor

Nov 02, 2008 | 1999 Chevrolet Tahoe

Not finding what you are looking for?
1998 Nissan Altima Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...