Question about 1995 Jeep Grand Cherokee

2 Answers

How can you chek codes on you own ithout a computer

Posted by on


2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 19,396 Answers

To check the codes on a 1995 you need an ODB code reader, then you connect the code reader to the ECM (computer module) that is located under the hood.

You find more details and explanation on how to read codes on the website below:

Jeep Grand Cherokee WJ - Diagnostic Trouble Codes

Posted on Feb 18, 2009

  • Level 1:

    An expert who has achieved level 1.


    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

This may or may not work for your vehicle but it does not do any harm to try. This will only work if you have the LED type display on your panel: Have a pen or pencil and a paper handy. Put key in ignition, turn to "on" position but DO NOT actually turn engine over, turn back to "off". Do this 3 times in a row and on the last turn, leave in on position. If this works you will see "P" and some numbers (example: P 0455). Write these codes down. When the display reads "done", then turn to off and remove your key. Google the codes you get using keys words such as " 1995 Jeep Grand Cherokee OBD code pxxxx(enter code number instead of x's) and go from there.

Posted on Oct 02, 2012


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

The chek engine is on and the engine doses not runs properly, the engine dos not turns ok

You need the engine control computer scanned for fault code.

Mar 22, 2018 | Cars & Trucks

1 Answer

What does a code 171 mean on a 2003 chevy alvalanche

po171 system too lean bank one first chek freeze frame data if code was set at cold engine subzero temp you may need reseal the intake on best scenario you have a vacuum leak affecting bank one double chek your fuel trims short term if adding fuel 2 digits look for vacuum leak if none foun unplug your uuper o2 for that bank and recheck trims any cheapy scan tool do this not until your trims are on short term +-3 at least this code will set if problem only in one bank do not replace maf sensr

Dec 09, 2013 | 1999 Chevrolet Silverado 1500

1 Answer

Fuel is not getting to the injecters, I sprayed starter fluid into the air intake, the car started then stoped

Hi, Check the fuel pump and fuses. Sounds like no fuel is getting to injectors. Also chek for computer codes this will give you an idea of where to look. Good luck.

Oct 14, 2011 | 2001 Pontiac Grand Am SE

1 Answer

I see chek gages sometimes & always chek engine on my grand cherokee 97 and i don't no what's the problem !

you can take it to auto zone and they can search the obd2 for a code. and they do it for free.

Sep 02, 2010 | 1997 Jeep Grand Cherokee

1 Answer

2004 wrangler chek engine light on. Code

a fuel cap indication would mean a leak not nessesaraly your gas cap, id check the fuel neck vent hose for a leak

Nov 04, 2009 | 2003 Jeep Wrangler

1 Answer

My 1991 chevy cavalier is dieing at idle. and wont start ithout my foot on the gas. it is fine at 1500 rpm but just about any lower than that i dies

check injectors,take your intake-plenum off you will see your fuel injectors. use an ohm meter attach to the injectors .you need 12 ohms on all injectors to be good .hope this helps

Oct 16, 2009 | 1991 Chevrolet Cavalier

1 Answer

Engine hi engine diagnose lite on scantool

ay chek all the ground wires that go to the ecm
chek alterneter and battery
chek ignation module and the knock sensor
every won was good
than ay change the ecm and the problem is over

Jun 20, 2009 | 1993 Buick Century

1 Answer

No overdrive engagement tacoma 2000

Yes, all po codes are a default code, you need to reset the computer by removing the positive cabel for 10 mins.

Nov 26, 2008 | 2001 Toyota 4Runner

1 Answer

Code 53

Code 53 is "internal pcm failure" pcm is powertrain control module or you main engine computer.Replace the computer.Good Luck!!!

Aug 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

492 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides