Question about Hyundai Motor 1995 Accent

1 Answer

To change gears, I need to fully press down on my clutch pedal to stop a grinding noise on my hyundai accent 2001Can I adjust the clutch cable,

Posted by on

  • Anonymous Mar 28, 2014

    It doesn't grind in forth gear as bad as all the others and it dose it in neutral when clutch is pressed down it stops

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 6,966 Answers

Hi and welcome to FixYa,

In a manual 2001 Hyundai Accent, the clutch cable could be adjusted. The adjustment point is on the cable 'pad' where it enters the firewall in the engine compartment.
to change gears, I need to fully press down on my - 86c2d7d.jpg
To adjust, the slack or free play must be decreased. This is done by turning the adjusting nut clockwise. Check back by pressing on the clutch pedal to your preference.
73309c3.jpg
Good luck and thank you for using FixYa.

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Car will not engauge into 1st or 2nd gear


the gear grinding noise is because the clutch plate is not fully disengaging and the input shaft is still driving. If you did not use the same length of push rod then the slave cylinder is not moving enough to disengage the clutch. Check it out that with the pedal on the floor the piston in the slave cylinder should be almost to the edge of the slave cylinder . That is where It should be to be working properly

Jan 13, 2014 | 2004 Pontiac Grand Am

1 Answer

Push down clutch makes grinding noise


cluch plate to be replaced, flaw in materail caused plate to shatter!

Oct 02, 2013 | Honda Civic Cars & Trucks

1 Answer

Fiat punto s60 wont go into gear after bleeding brakes and clutch


Well it's sounds like to me that the grinding sound you hear is throwout bearing, and as far as no clutch, if you don't have no clutch pedal what I mean is it don't feel lime it used to that is your slave cylinder, it needs replaced, usually when they go out they just go, don't give no warning

Dec 24, 2011 | Cars & Trucks

1 Answer

Grinding noise after shifting


The clutch pedal need to be adjusted ,while you press the pedal clutch,it is not disengage fully the gear box that why when you shift it make that noise,well hope that clear your mind and help you.

Jan 28, 2010 | 1997 Honda CR-V

1 Answer

Grinding Noise When Clutch Is Depressed, Lights Flicker


you may need to have your clutch cable adjusted ... it is most likely not releasing the clutch fully and grinding against the flywheel

Oct 06, 2009 | 1998 Volkswagen Jetta

2 Answers

NOISE WHEN LETTING OUT CLUTCH WHILE IN GEAR


Clutch plate springs brocken.Thats where your noise is comming from.The only solution is to change the clutch.Hope that was helpfull.

Jul 24, 2009 | 1993 Toyota 4Runner

4 Answers

Grinding when engaging into gear when warmed up.


ok every time you open the clutch resevoir you have to bleed the slave ..next hold down the clutch to the floor open the bleeder screw 10 mm bolt and then close it and pick the pedal up off the floor if your clutch is not right the pressure plate is failing most likely on mitstu stuff ...bleed first ..

May 08, 2009 | 1990 Eagle Talon

Not finding what you are looking for?
Hyundai Motor 1995 Accent Logo

1,131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...