Question about BMW 325

1 Answer

Remove master clutch cylinder on 1992 bmw 325i

How to remove master clutch cylinder on 1992 bmw 325i

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • BMW Master
  • 6,674 Answers

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much im i looking to spend on a bmw 325i e46 cluch kit


up to $900.00 for the clutch kit and the same for the labor job
have the clutch master cylinder checked first because most clutch problems start there
take it to an accredited professional brake and clutch shop for a proper diagnosis and quote

Apr 18, 2017 | BMW Cars & Trucks

1 Answer

Bmw 325i 2002 automatic convert to manual gearbox


It will take time and some mechanical skills . You will need a clutch pedal and bracket, master cylinder and slave cylinder and hose, flywheel and clutch pack, throw out arm and bearing, hole cut in the floor for the gear lever, all the insulators and rubber boots, possible a different rear engine mount and cross member, wiring harness for the reverse switch and other switches on the gear box, probably a different length drive shaft, switches for the cruise control operation. Everything can be obtained from a BMW wreckers and a good workshop manual will be a good investment.

May 12, 2014 | Cars & Trucks

1 Answer

Clutch piston too short?


sounds more like a seal to me

Sep 16, 2012 | 1997 Mazda MX-5 Miata

1 Answer

Clutch looses pressure, leaking by clutch peddle


Clutch master cylinder is leaking out of piston cup.Detach from clutch pedal, disconnect hydralic line, and remove 2 firewall retaining bolts or nuts and pull out. Replace clutch master and bleed line at clutch slave cylinder.

Dec 13, 2010 | 1992 Nissan Pickup

1 Answer

Clutch hydraulics on my BMW problem - quick fix. I went to use my 1992 318 BMW after not using it for a week and the clutch pedal had no pressure. The AA couldn't fix it so they towed it to my nearest...


THEY PUT IN NEW FLUID AND BLEED AIR OUT OF THE SLAVE MASTERCYLINDER.IF THE CLUTCH PEDAL GOES TO FLOOR AGAIN.YOU HAVE A LEAK AT CLUTCH MASTER CYLINDER.OR THE MASTER CYLINDER IT SELF GOING BAD.

Mar 08, 2010 | BMW 318 Cars & Trucks

1 Answer

I cant locate the fuel pump relay on my 1992 325i BMW Cabrio


The replay is beside the Fuse Box beside the Brake Master Cylinder, left side of the firewall.

Sep 07, 2009 | 1996 BMW 318

1 Answer

1992 bmw ignition lock assembly replacement


BMW ignition lock replacing.

According to manual no special tools needed. here procedure!

  1. Ignition elec switch. Disconnect battery. 2. remove trimpanel from lower leftside of instrument panel. remove screw retaining lower steering column and remove cove. 3. remove slotted screws on both side of switch. 4. relase tabs and remove switch from elec harnass and remove sealer.. note: before mating new ignition elec switch check that switch is in correct position. seal screws again.
  2. Ignition lock cylinder replacing. 1. insert master key and turn 60 deg to radio position. 2. inset piece of stiff wire into opening in lock cylinder and pull cylinder out. (Note early models up to 10/95 turn lock cylinder back 12 deg to release)

Jun 13, 2009 | 1992 BMW 3 Series

1 Answer

CLUTCH PEDAL WON'T SPRING BACK


Your hydraulic clutch has failed, either the master or slave cylinder, It is recommended they be replaced as a pair.

Dec 16, 2008 | 1998 Chevrolet Cavalier

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

565 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...