Question about Ford F-150

1 Answer

96 ford taurus 3.0 is knocking out of gear when at a stop and is hard to get into gear

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 120 Answers

Sometimes there is two bolts underneath the dash follow the shifter cable to where it hooks to the steering wheel see if it is loose then tighen them up i hope this helps you

Posted on Feb 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

96 taurus ax4n tranny


You might need to replace the valve body clip with the upgraded (stronger) one. Ford had problems for a while with the clip breaking and not allowing the tranny to shift into O/D. I had the no O/D problem, I replaced the clip with the upgraded (stronger) one which fixed the problem.

fix with this kit
Sonnax 96206-07K AX4N 4F50N Transmission forward control valve, Transmissionpartsusa.com

Below are the DTC codes if it has any. ISSUE
No 4th gear operation (no 3-4 shift) and Diagnostic Trouble Codes (DTCs) P0734 and/or P0761 or 648 may occur on some vehicles.

Nov 19, 2013 | 1996 Ford Taurus

1 Answer

Step by step instructions on how to fix knock sensor in 92 ford taurus


Step by step instructions on how to fix knock sensor in 92 ford taurus

Feb 21, 2013 | 1992 Ford Taurus

1 Answer

Having trouble getting a 96 ford taurus wagon out of park


theres i locking pin in there that is problyu going bad you will have to bent bake or replace it hope this helps

Sep 21, 2009 | 1996 Ford Taurus

1 Answer

1999 ford taurus has reverse but no forward gears could transmission range sensor be the problem


I have been hearing about the trans planetary failing on 96-02 taurus/sables. My personal 98 sable 3.0 expired that way.

Jul 08, 2009 | 1999 Ford Taurus

1 Answer

96 Ford Taurus GL Revving problem when stop then go


Did you check the transmission fluid again. You could have a major leak. Or reving the car up so high it started to burn the clutches in your transmission, resulting in replacing the transmission. Always check the fluid. A few dollars for fluid is better than 1500 bucks for a new tranny

Mar 31, 2009 | 1996 Ford Taurus

1 Answer

96 taurus wagon goes to neutral when vehicle comes to full stop.


That would be your neutral park switch is bad or broken. If the shifter linkage is not aligned with the neutral park switch it will not work properly. Located on drivers side on top of Trans.

Mar 22, 2009 | 1996 Ford Taurus

1 Answer

Knocking noise in 3.8 lit 95 ford taurus


You can not put a liquid where metal is supposed to be. Just a general rule of thumb. The high RPM's had been too much for the engine, and A rod bearing, or rod knocking is about the same thing. Dont try the heavier oil thing, I hate when ppl suggest such stuff. Just replace the bearing, or in most cases and cost efficent, the engine.

Jan 15, 2009 | 2002 Hyundai Santa Fe

1 Answer

1996 FORD TAURUS GE


Just a piece of advice: could be the oil which lubricates the gears. Try changing your engine oil, maybe it has gotten a little too old and lost its lubricating properties.

Jul 21, 2008 | 1996 Ford Taurus

1 Answer

96 Taurus brakes


Presuming you have NO leaks in the hydraulic system,it would be a bad brake master cylinder.What's happening is,the piston inside the master cylinder has rubber seals,and when the pedal goes to the floor,the master cylinder is leaking internally,past the rubber seals.If the brake booster was bad,the symptom would be an extrememly HARD,unresponsive,brake pedal,and the engine would idle terrible (vacuum leak).Good luck.

Jul 10, 2008 | 1994 Ford Taurus

Not finding what you are looking for?

Open Questions:

Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...