Question about 1999 Ford F250 Regular Cab

Open Question

Won't start 1996 ford f-250 7.3 diesel

Installed auto page system 2 yrs ago( alarm,self start) starter engaged during driving,have replaced starter,solinoid,and starter relay,checked all fuses and relays .Have disconnected alarm system all electrical will work such as lights radio and etc.When trying to start with key cylinder by passed or manual @ neutral safety switch nothing but if key or neutral switch is in the on or run position jump wire the 2 terminals @ the starter relay (fender) and it will run/ drive.Once you turn it off you will have to jump the terminals again.Allready replaced 2 fender relays 1 starter with solinoid 1 neutral safety switch Note there is no voltage to the relay (fender) when trying to start in normal operation

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ginko
  • 19396 Answers

SOURCE: unable to start/ 2000 F250 V10

Try first unplugging battery cable for five minutes, this sometimes fix the problem. If it does not replace electric windows relay and electric windows fuse.

Posted on Jul 26, 2008

  • 1 Answer

SOURCE: 95 F150 wont crank

the starter should be replaced. The solenoid is kikcing the pinion out but there is no contact being made to turn the starter motor. I have the exact same truck and before i changed the starter used the old starter tap trick. Tap the starter casing with a hammer and it should start turning again. hope this was helpful for you. Good luck.

Posted on Nov 07, 2008

wdmb08
  • 34 Answers

SOURCE: Wont Start

Could be the strater itself or bad connection to the starter from relay

Posted on Nov 20, 2008

yotaguy
  • 232 Answers

SOURCE: need wiring diagram

Go to autozone.com and register they have good wiring diagrams for your truck.What I saw was all the relays going to ground so you should have 12V coming off the ignition switch.

Posted on Jun 01, 2009

jyackle5
  • 8197 Answers

SOURCE: neutral safety switch 1991 camry 4 cyl

Well, not necessarily need a professional if you have some basic maintenance experience.

If you look at the engine compartment from the front of the car, the switch is located at right side, very close to the radiator, close to the bottom of the car. You will see the shifting cable as well as an electronic connector on it. You can try if you shift, the cable will rotate the arm on the switch.

According to my experience, it's not easy for the switch to go bad, it may just need some alignment so the switch angle is zeroed in wrt the contact points. There is a line on the switch for alignment purpose.


To replace it is not difficult at all, once you located it, you will see. You can get a used one at junk yard, I believe it will be much much cheaper.

Posted on Nov 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

REMOVED ALARM -STARTER WON'T ENGAGE-NO POWER TO ENGINE


When you removed the alarm unit you cut the line to the Starter kill switch that was installed. Remove the starter kill switch which is most likely located under the dash spliced into the ignition wiring harness.

Jul 08, 2011 | 1999 Dodge Intrepid

1 Answer

Horn and parking lights flash off and on randomly after auto is started and while driving


sounds like alarm system problem is there a car starter installed and not properly installed or antivol system and do you have a hood switch that is broke try to disconnect hood switch to see if this will stop as well if you have a car starter installed maybe to unplug and testthe original alarm system or contact dealer for tsbs on alarm system problems

Dec 30, 2010 | 1999 Toyota Avalon

2 Answers

The engine on my 1986 f-250 6.9L diesel won't turn over. The starter engages but immediatly disengages.It happened as I was driving down the road there was a noise like the fan was hitting then a loud pop,...


Either the timing chain has broken or the Starter motor bendix assy has come adrift and jamed up in the bell housing,and if engaged while engine was going a lot more damage will be found.,but why the powerd steering hose blew off i cannot answer that one ..
so could you let me know when you find out.. Ron

Oct 15, 2009 | 1986 Ford F 250

1 Answer

I have 1984 ford F250 diesel. when you try to start all electrical shuts down. Its comes back after a few min. could it be the starter is shorting out causing a breaker to engage?


had same problem it was corrosion on the battery terminal + side where all the red wires connect. you probably have 2 batteries check both

Aug 24, 2009 | 1984 Ford F 250

2 Answers

How to get top bolt off of 1988 F250, 7.1 L diesel starter


You need a long extension and swivels for a rachet to get to the one bolt thats on top next to the block. Check for a way to get to it from the front.

Jun 25, 2009 | 1988 Ford F 250

1 Answer

Have a 85 f-250 diesel that won't start


7.3 diesel i assume?i had one years ago and the controller for the glow plugs went bad,couldnt heat up the fuel enough to ignite,or the injection pump went bad or is out of timing

Apr 25, 2009 | 1985 Ford F 250

2 Answers

96 explorer turns over but starter is not engaging


I always check remans before they are installed; the Bendix may not be advancing the starter gear or you may have teeth missing from the flywheel. I'd pull the starter and check the condition of the flyhweel. 

Jan 23, 2009 | 1996 Ford Explorer

2 Answers

1985 Ford 250 Diesel Truck, Won't Start


just crack the injector nut crank it over till fuel comes out tighten nut,and so on to the others.

Jan 15, 2009 | 1985 Ford F 250

1 Answer

1999 navigator


i know this worked with my 99 navigator 32 valve used a viper car starter.

Lincoln

Navigator

1997-2003

Remote Starter Wiring Colors and Notes

Function
Vehicle Color
Location

Start:
RED/LT. BLUE
IGNITION SWITCH HARNESS **

Ignition #1:
D BLUE/GREEN
IGNITION SWITCH HARNESS

Ignition #2:
GRAY/YELLOW
IGNITION SWITCH HARNESS

Ignition #3:
RED/BLACK
IGNITION SWITCH HARNESS***

Accessory:
BLACK/LT. GREEN
IGNITION SWITCH HARNESS

Brake Light:
L GREEN (+)
AT SWITCH ABOVE BRAKE PEDAL

Tach Signal:
WHITE/PINK
AT POWERTRAIN CONTROL MODULE *

Parking Lights:
BROWN (+)
AT HEADLIGHT SWITCH

Headlights:
RED/YELLOW (+)
AT HEADLIGHT SWITCH

OEM Alarm Disarm:
D GREEN/PURPLE (-)
DRIVER KICK PANEL

OEM Alarm Arm:
N/A


Diesel Glow Plug:



Clutch Bypass Wire:



Notes:
* Powertrain Control Module (PCM) Located On Passenger Side Of Engine Compartment On Passenger Wheelwell. This Wire Can Also Be Found At the Firewall Harness On the Driver's Side of Vehicle. ** This Vehicle Is Equipped With Ford's PATS Anti-Theft System. Use Universal Alarm Bypass Module part # 2x402 where X can be any number. *** Must power ign3 using a relay. Tap relay coil to ign3 connection of remote start along with bypass module. No diode isolation is required.

Aug 07, 2008 | 1999 Lincoln Navigator

Not finding what you are looking for?
1999 Ford F250 Regular Cab Logo

Related Topics:

513 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...