Question about 1983 Buick Electra

Open Question

1983 buick park avenue steering fluid pump

I have a 1983 buick electra park avenue. I need to replace the steering fluid pump. Is there a website that has diagrams specifically for my 1983 buick that can show me how to do this?

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


SOURCE: need a routing diagram for

If you still have the car manual that came with the car, it is in the book.

Posted on Dec 31, 2008

  • 1118 Answers

SOURCE: change fuel pump on 1994 buick park avenue

Drain all gas as much as possible for weight reasons, Unhook fuel lines, unhook electrical connections, and ground connections, filler tube, and straps, then tank will drop out. Remove retaining ring on sending unit remove unit from tank taking note how it comes out because its got to go back in the same way it came out, chg. pump on sending unit there is one electrical plug, reinstall unit in tank with retaining ring, assemble in reverse order.

Posted on Feb 14, 2009

  • 1050 Answers

SOURCE: removing water pump 98 buick park avenue

You need to poke a small extension with a 13mm socket through the holes in the power steering pulley, undo it, and slide it back.

Posted on Mar 17, 2009

  • 1 Answer

SOURCE: '98 Buick Park Avenue Signal Switch Replacement

I have same problem with my 1998. How do I find instructions for replacement of same.

Posted on Apr 19, 2009

  • 2 Answers

SOURCE: Buick Park Avenue rear suspension pump noise

You may have to replace it but money wise it is a lot of times cheaper to convert over to standard shock/strut suspension than it is to buy the pump

Posted on Aug 03, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Need to replace the fuse for the turn signals, where would I find them?

1989 Buick Park Avenue ? Didn't have ParK Ave. that year . Buick Park Avenue
It became an Electra trim level in 1978 and its own model starting in 1991 after the Electra was discontinued. Two generations of the Park Avenue were manufactured in the United States until 2005, while in 2007 the nameplate was revived on a large Buick sedan built by Shanghai GM for the Chinese market based on the Holden Caprice from the WM/WN range. The nameplate is derived from the affluent

Feb 07, 2017 | Buick Park Avenue Cars & Trucks

1 Answer


The tank should be right on the pump, on top of the engine.
The cap says "power steering do not overfill'.

Feb 18, 2014 | 2000 Buick LeSabre

1 Answer

1983 buick electra park avenue voltage regulator

regulator is inside alternator / check 2 wire connector at rear of alt.
how are you checking alt. / test amp output withand with out load

Dec 29, 2013 | Buick Cars & Trucks

1 Answer


should be a cap that says power steering on it or has pic of steering wheel should be on drivers side of engine

Feb 13, 2013 | 1997 Buick Park Avenue

1 Answer

Where is the power steering pump reserviour for my 2003 Buick Park Avenue Ultra located?

The power steering pump reservoir is always located on top of the steering pump itself. It has a screw cap about two inches diameter with the POWER STEERING FLUID words on it, the cap has a dipstick integrated to check fluid level, DO NOT OVERFILL. Check only when engine is NOT RUNNING. Don't forget to rate this post!!!

Sep 29, 2010 | Buick Park Avenue Cars & Trucks

1 Answer

95 buick park ave power steering pump bolts

I think any dealer would have these on hand; if my memory is working right, these did have to be a specific class and will need to be torqued carefully to avoid stripping the female threads.  

Feb 16, 2009 | 1995 Buick Park Avenue

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts


Level 3 Expert

78010 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides