Question about 1989 Plymouth Sundance

1 Answer

Key stuck in ignition on 89 plymouth sundance

My grandson put the key of my 89 plymouth sundance in crooked and now the key won't come out or turn. I tried turning the steering wheel back and forth as much as I could turn it and it didn't help at all. Is there anyway to get the key out without taking the ignition apart?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 359 Answers

Without taking the ignition apart, you will really have to do some work, what you might want to do is get in the passenger side, grab the key with a good set of pliers, and get some leverage. If you grab, move the key back and forth while jiggling the wheel, the lock should come loose and the key should slide out. Be careful not to turn the key too far, because then you'll break it off, hope that works.

Posted on Feb 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of key release 94 sundance


a worn key, worn key tumbler or damaged key switch. it will need to be replaced.

Jul 13, 2014 | 1994 Plymouth Sundance

1 Answer

No start


Sounds like your starter is about the only thing you have not changed. Check that you have power going to it when you turn the key if thats not it try replacing the starter.

Sep 18, 2012 | 1994 Plymouth Sundance

1 Answer

92 plymouth sundance. loud pop on drivers side when turning. steering wheel won't turn when brake is pressed.


thats your axle its bad or you call it cvc joint needs to be replace it cost about $150

Apr 26, 2012 | 1992 Plymouth Sundance

1 Answer

1998 Plymouth grand voyager ignition won't turn


I have had this happen on my 98 Voyager. Just have a new key cut. This new key will sometimes cure the problem. The older keys get worn out and won't unlock the ignition. Try this before a much more expensive and time consuming change of the ignition.

Nov 01, 2011 | 1998 Plymouth Voyager

1 Answer

1993 Plymouth Sundance 2.2L cranks, no start


When you turn the ignition on the pump is energized for 2 to 3 seconds. did you check it like that. it is also energized when cranking the engine. there is a fuse then a relay then the fuel pump. the relay is ran/ energized by the ecm computer. if there is a fuse relay box under the hood you'll need to check there to. good luck

Jun 17, 2010 | 1993 Plymouth Sundance

1 Answer

Where is the relay located for the turn signals on an 89 plymouth sundance? The lights work on the signals, but don't blink when you turn them on


your fuse block is located behind the steering column cover acessible by removing the fuse access panel above the hood latch release lever.the relay and flasher module is located behind an access panel in the glove box.included in the module are hazard and turn signal flashers along with time delay and horn relays.you have additional relays mounted on the inner fender panel near the battery and strut tower.

Dec 13, 2009 | 1994 Plymouth Sundance

1 Answer

1993 plymouth Sundance-Ignition switch problems


the ing. switch brake on these models replace the switch

Mar 04, 2009 | 1993 Plymouth Sundance

1 Answer

I need help getting the transmission out of a 89 plymouth sundance I am stuck on the tri axel and dont know what I have to do to get it out, its all unbolted I just need it to fall is there a diagram or...


I assume by tri axle you mean driveshafts. If the driveshafts are still in then you need to remove them both. Unbolt them from the steering knuckles ( unbolt the ball joint, axle nut, sway bar assy ) move the knuckle assy out of the way and then the axles should pry out at the tranmission end ( screw driver between axle end and trans housing should do the trick). Hope this helps.

Jan 06, 2009 | 1989 Plymouth Sundance

1 Answer

'89 plymouth sundance


You need a timing belt

Aug 09, 2008 | 1989 Plymouth Sundance

Not finding what you are looking for?
Cars & Trucks Logo

157 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

64034 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...