Question about 1996 Honda Accord

1 Answer

Need to change the thermostat on a '96 honda accord ex-r v-6

I see two rad hoses going to a housing under the throttle body. where is the thermostat as I don't want to tear apart the entire area of the engine

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 491 Answers

Where those hoses are is the thermostat housing

Posted on Feb 18, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Change thermostat on 2004 chevy impala?


first you need drain engine coolant down below thermostat. what engine type 3.8 or 3.4 need to know.the 3.8 engine thermostat housing on top intake follow top radiator hose to thermostat housing.the 3.4 engine you have to remove air filter housing with air inlet duct with mass air flow sensor.you have to remove throttle body with coolant hoses.go to auto parts store buy new throttle body hoses old ones will be hard to remove might have to cut two small hoses also buy new throttle body gasket also. before you can remove throttle body unit you have to remove accelerator cable and downshift cable from bracket bolted to throttle body.once throttle body remove then you can remove thermostat housing bolt remove replace thermostat.

Nov 11, 2011 | 2004 Chevrolet Impala

2 Answers

Where is the thermostate housing for my 1997 accord ex 6cyl 2.7 automatic


Removal & Installation follow top rad hose passenger side. there are two bolts and temp sensor remove. 91183p23.gif

Oct 30, 2010 | 1997 Honda Accord

1 Answer

Where is the thermostat accord ex 1995


Follow the radiator hose that goes around the back of the engine, remove hose and two small bolt's that hold thermostat housing, thermostat will be under that housing.

Jun 11, 2010 | 1992 Honda Accord

1 Answer

I own a impala 2003 and i would like to know how to change the thermostat on it.The motor is a 3.4 liters


Drain radiator. Remove upper rad hose from thermostat housing. Disconnect air intake hose from throttle body. Remove throttle body from upper intake manifold, disconnecting the 2 rubber hoses to the heater line. You may also need to disconnect the fuel line. Remove the exhaust crossover heat shield and loosen the crossover pipe from both exhaust manifolds but don't remove crossover completely. You should have access to the 2 thermostat housing bolts, remove upper bolt but just loosen the lower one about a half inch. Pull the housing out and up from the intake manifold to access the thermostat. Clean the mating surfaces with a gasket remover. replace thermostat, apply a light coating of rtv sealant to both sides of the new gasket. Replace thermostat housing with the gasket to the intake manifold. Apply some rtv to the bolt threads before reattaching housing. Tighten bolts snugly but do not over tighten. Tighten exhaust crossover and reattach the heat shield. Install throttle body attaching the 2 little hoses at the bottom, its a good time to replace these hoses and clamps. Depending on the condition of the throttle body gasket you may need to replace it also. Reconnect the fuel line (if disconnected) Reconnect air intake hose to throttle body. Reattach the upper rad hose to housing. Fill rad with coolant 50/50 mix with water (make sure to use the same type antifreeze that is in the system, they say you can mix green with red but I wouldn't recommend) Leave rad cap off start the car and let it warm up until you can see the coolant circulating and ad coolant as necessary until full. Now there is going to be some air in the system that you need to bleed out. There are 2 bleeders on this system, 1 is on the top of the thermostat housing, and the other is on the metal heater line on top of the water pump (the one that goes across the front of the engine and around under the throttle body that the two little hoses attach to) Bleed the one on the housing first (its the lower one) open it until fluid comes out then tighten it. Then move to the 1 on the heater line(above water pump) loosen it until fluid comes out the re-tighten. Fill recovery tank to fill line replace the rad cap and take it for a ride, watching the temp gage closely. If the temp goes higher than normal than there is probably more air in the system. you'll have to bleed it again.
This is a very labor intensive procedure and I do recommend buying or checking a service manual out from your local library. I've done these in the past and to be honest I just have the dealer do it now. A system flush and thermostat replacement was around $230 the last time I had it done, but it comes with a warranty. And you wont have to rent or buy a fuel line disconnect tool if you end up having to disconnect it. These are the hardest thermostats I've ever replaced.

Jun 09, 2010 | 2003 Chevrolet Impala

2 Answers

Car is overheating


3.1 motor under the upper intake at the end of the upper radiator hose

Jan 17, 2010 | 1997 Chevrolet Lumina

2 Answers

Where do i find the thermostat for a 1993 honda accord


the thermostat is located where the lower radiator hose goes into the engine

Aug 01, 2009 | 1993 Honda Accord

1 Answer

Change thermostat in a 1992 honda accrod lx


Two bolts in the housing at the bottom of your top rad hose. Thermostat is under that. remove replace thermostat and gasket. Re-fill anti freeze.

May 15, 2009 | 1993 Honda Accord

2 Answers

I need to know where the coolant sensor is on the 2001 Honda Accord EX


find the thermostat housing and look on the radiator

Mar 30, 2009 | 2001 Honda Accord

2 Answers

Where & how to install thermostat in honda accord ex 1992


you need to follow the upper hose that lead from the radiator to the engine, there is two bolt that connect the thermostat housing to the block loosen the bolt using a 10 mm socket with ra-chet. Make sure that the engine is cool off before attempt to do this you will lose coolant but that's ok you will add the coolant when you finish replacing the thermostat. start the engine with the radiator cap off then add coolant slowly and cap it, then fill the reservoir up.

note the way you remove the thermostat that's the same way you will put the new one so pay attention when you remove the old one good luck.

Dec 17, 2008 | 1992 Honda Accord

1 Answer

Speed Sensor


HI..
The Speed sensor on your Honda Accord 97.
Is located on the Transmission.
If you follow the Lower Radiator hose from the rad to the engine.
The hose end on the Thermostat housing.
OK.. Just on direction of the thermostat housing .
Under the housing you Will see on the transmission the Speed sensor, with a connector of 3 wires. Is the only sensor at this
Part of the Transmission..

Ok. I hope this work on your question.
Thank you for use fixya..

Sep 09, 2008 | 1997 Honda Accord

Not finding what you are looking for?
1996 Honda Accord Logo

Related Topics:

571 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...