Question about 2006 Ford Expedition

1 Answer

2006 ford expedion blower motor only has high speed

I was told this happens when a resistor module goes bad. Can you please let me know how to access it?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Ford Master
  • 783 Answers

Remove the RH lower instrument panel insulator under the dash you should then see it,has one screw holding it to the blower case.It will have OG/BK,LG/WH,YE/RD,BK wires if it is a manual system.If electronic climate control the wire colors will be VT/WH,TN/OG,RD/WH.BK

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My 2006 blower fan switch only has a high. As soon as I turn it on it goes to high. Would this also be the relay?


this sounds like a bad blower motor resistor board that has gone bad. they are designed to work only on high if they go bad so you will still have the blower to defrost the windows.

Sep 10, 2014 | 2006 Nissan Titan

2 Answers

Location of the resister for the heater fan 350 ford 2006


Its under dash panel.

HEATER BLOWER MOTOR


Its faulty blower motor resistor. The low and medium speed on blower motor is controlled by resistor and its actual speed is high. So because resistor is not working, blower motors actual speed which is high is working.


It can be faulty blower motor or faulty blower motor resistor. Get the blower motor inspected. If it's faulty it has to be replaced.


=======

For blower motor testing and replacing, check the link below: ----

Blower motor Testing/replacing for all vehicles?

http://repairhelpcenter.blogspot.in/2012/02/blower-motor-replacing-for-all-vehicles.html

------------

These will help.

Thanks.

Nov 28, 2012 | Ford F-350 Cars & Trucks

1 Answer

My 2006 GMC Envoy heater fan has stopped working. I checked the switch and it is good. I didn't know how to get to motor itself to check it there. Any suggestions?


The blower motor is located behind the glove box. Open the glove box and at the left rear is a wire catch mechanism, push on this and the box will move further down. The motor and blower motor resistor module can be accessed here. Does the blower work on any of the speeds? If yes, then suspect the resistor module. If no, check for a blown fuse or bad motor.

Feb 26, 2011 | 2005 GMC Envoy

1 Answer

Heater/defrost/ac does not blow in my 2006 tacoma. worked this morning, parked at work, came out half hour later and would not work.


what has most likely happened is that a fuse has blown that is in your blower fan circuit. Check your owners manual, and see if there is a fuse to that system, if there is, check and see if it is blown. If it isn't, then the problem could either be your blower fan itself, or your blower motor resistor. Generally, when the blower fan goes bad, no speeds of the fan work. When the Blower motor resistor goes bad, usually only 1 speed of the fan works. Try the first suggestion i gave, and it everything checks out in the fuse box, then try all of your fan speeds. If one works, you need a blower motor resistor, if none work, then it is most likely your fan. Let me know how it goes and i'll do my best to assist you further. good luck.

Jan 13, 2011 | 2006 Toyota Tacoma

1 Answer

I have 2002 infinity I35 and the blower motor stop working ,I took out the blower motor to make sure was good. YES the blower motor still working .the only think I really don't know how to check is Blower...


WELL YOU HAVE TO USE A VOLT METER CONNECT ONE VOLT METER WIRES TO GOOD GROUND AND THE OTHER VOLT METER WIRES GOES TO EACH SWITCH SPEED.IF VOLT METER GET VOLTAGE A 1 OR 2 CONTROL SPEED RESISTOR BAD.IF RESISTOR BAD YOU WILL GET 1 OR 2 BLOWER MOTOR SPEEDS.IF BLOWER MOTOR WORKING.CHECK THE AC AND HEATER CONTROL SWITCH FUSE OR CHECK BLOWER MOTOR FUSE AND RELAY.IF ALL GOOD SO FAR CONTROL SWITCH ITSELF COULD BE FAULTY.

Nov 05, 2010 | Infiniti I35 Cars & Trucks

1 Answer

The climate control system only has the high fan speed. Is this likely to be the panel control switch?


May be but next to the blower motor is the blower control module this has a series of resistors in it to change the current flow to the blower motor ,.When you call for high speed on the fan it bypasse's the resistor module, on all other speeds it runs through the resistor. so check for power going into the blower module from the control panel on some speed other than high if power is at the module control panel is ok. if not blower module is bad

Oct 23, 2010 | 1999 Pontiac Grand Am GT

3 Answers

My a/c only works on high. I was told that it was the blower motor resistor not sure where is located.


It's located near the fan motor on the passenger side duct work. It will have a harness plugged into it.
It's mounted with 2 sonic welds, to remove it pry under the mounting points to snap the welds. The replacement resistor is mounted with 2 self tapping screws.

Jul 21, 2010 | 2006 Chevrolet Colorado

1 Answer

Heater fan only works on high speed .This truck has auto climate control but also has a manual fan speed switch


This is very likely a bad blower motor resistor. When this resistor goes bad you have only off or high. I hope this helps.

Mar 21, 2010 | 2006 Ford F 350 Super Duty

1 Answer

2006 ford superduty blower motor runs on high at all times. climate control system. what are the volt meter test readings I should look for from the controller.


sounds like the blower motor resistor assembly is bad.when it goes bad the fan defaults to high for safety purposes.

Oct 26, 2009 | 2006 Ford F 350 Super Duty

1 Answer

2006 Ford Explorer XLT the Blower Fan only works on 4 and 3 Sp


Look under the dash on passenger side and just to the left of the blower motor housing you will see the 4WD control module.Remove the 2 screws holding the module and let it hang down and your resistors are behind this.Remove the 2 screws holding the resistors and remove.
Now I am assuming you have manual climate control and not electonic.

Feb 25, 2009 | 2006 Ford Explorer

Not finding what you are looking for?
2006 Ford Expedition Logo

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...