Question about 2004 Nissan Quest

3 Answers

My 2004 nissan quest has awful Brake judder even after new rotors and pads. Went with after mkt set up and still same problem.

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There is a factory TSB from Nissan regarding this. Please see NIssan Service Bulletin NTB07-062. Covers years 04 through July 07.

Posted on Jul 02, 2011

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 202 Answers

Mostly likely it is the rear. take drums off and resurface drums.

worst case scenerio
bad tie rod ends vibrating the steering wheel while stopping.
thanks jeff

Posted on Feb 17, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 9 Answers

Is your abs light on could be abs problems or you could have air pockets in brake line may need to bleed brakes

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Knocking sound when braking 2007 Nissan quest


You have brake rotors that are warped, replace them and the brake pads.

Jan 17, 2014 | 2007 Nissan Quest 3.5 Minivan

1 Answer

Juddering after changing front tyres and pads


If you just changed the brake pads with out machining the disc rotors then that will give you a problem straight up especially if the rotors were damaged from the pads worn down too far. There is a way of putting on new tyres and if not fitted correctly you may get a problem there as well. Check the mould line on the side of the tyre that is almost at the rim and see if it is the same distance from the rim all the way around on both sides . This will show if the tyres have been fitted correctly

Nov 29, 2013 | Cars & Trucks

1 Answer

My 2007 nissan quest 3.5S mini van is in almost perfect condition until I recently discovered something deviating from what I know is common to brakes. I do all maintenance work to my cars (nissan VW,...


Master cylinder and/or brake booster could be the problem. A tiny bit of air in the system will effect your braking abilty. A fault in the ABS system would prompt the computer to trigger the ABS light. If you have brake shoes on the rear, make sure they are properly adjusted. Hope this helps.

Jul 04, 2011 | 2007 Nissan Quest 3.5 Minivan

3 Answers

1999 nissan quest brakes over heating


even though the parts are new they can still be bad the calipers are sticking have him replace them at no cost due to part being bad if he says no then go elsewhere

May 14, 2009 | 1999 Nissan Quest

1 Answer

I have a 2002 Nissan Quest and the rear brakes are making grinding and squeaking noises while braking. The rear brakes were replaced a month ago and since then it's been making those noises. I have read...


Make sure the rotors (the disks that the tire rim are mounted on), are smooth. If they are rough, then they are wearing your break pads down. Even if the break pads are new, bad rotors will grind them down. Change the rotors...

May 03, 2009 | 1994 Nissan Quest

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

Brake pads


this page offers an excellent guide

http://www.autozone.com/addVehicleId,2927501/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c15280190996

Robert

Please take a moment to rate this solution.. thanks

Jan 31, 2009 | 2004 Nissan Quest

2 Answers

2005 Dodge Durango Front Brake Squeal


Did you buy factory pads or get cheap aftermarket pads? If aftermarket did you get the ceramic? The cheap aftermarket ones tend to squeal pretty bad. Like the last comment on here, you should have your rotors turned whenever you change the pads.

Jan 13, 2009 | 2005 Dodge Durango

1 Answer

Change rotors


also if your car shakes when you stop your roters are warped.

You may need to take it into a brake shop as the procedure is to long and complicated to type out and it varies from car to car...

Oct 14, 2008 | 2004 Nissan Quest

2 Answers

1999 nissan quest brake pad replacement


Remove wheel & tire,
remove 2 torx bolts that go from the inside to the outside of the vehicle. They are on the inner side of the brake caliper.
lift the caliper out of the rotor.
remove the brake pads.
To install, you must first squeeze the caliper piston back inot its bore. Do this slowly to prevent damage to the piston. You are forcing excess brake fluid back into the master cylinder reservoir. Slow constant pressure will get the job done. Use a large c clamp or a wooden hammer handel if that's all you have.
Fit the new brake pads in the calipers and slide the assembly back over the rotor.
install the 2 torx bolts, size 40? head I think.
You are done.
If rotors are scored bad, replace them too.

Jun 07, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
2004 Nissan Quest Logo

480 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...