Question about 2005 Chevrolet Avalanche

1 Answer

Where are the rear oxygen sensors located& how do i tell whitch one is bad on 2004 avalanc????

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 74 Answers

Located before the CAT(catalyst) which looks like an extra muffler

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the 2004 Ford Mustang Heated oxygen sensor bank 2 sensor 1 located.


bank 2 is on the drivers side of motor. sensor 1 is the first sensor you come to in the exhaust going from the exhaust manifold to the rear of the car.

Sep 11, 2015 | 2004 Ford Mustang

2 Answers

Where is the oxygen sensor for 2004 dodge durango 4 wheel drive?


It has 4 . 2 upstream of the cats 2 after the cats . Whitch one are you looking for

Apr 18, 2015 | 2004 Dodge Durango

2 Answers

Code p0159 what is this


159, (USA?) must be V6 or V8 it has 2 banks.
first google hit
Possible causes
- Faulty Rear Heated Oxygen Sensor Bank 2
- Rear Heated Oxygen Sensor Bank 2 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 2 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks

let me condense this.
1: the right bank rear 02 sensors is reading wrong,
note I did not say it was bad. dig?
2: this means the CAT on that side, is UNHAPPY.

unhappy can be , as it said air leaks anywhere near the front or rear of Bank 2 CAT.
unhappy 2, is the engine fuel controls are totally out of control
way rich or lean, out of control;
unhappy3, gross misfire, or all the above at once.

the ECU(pcm) at no time ever KNOW what is wrong, it only can flag bad inputs. or tests that fail , tests are called (USA,OBD2 SAE) called Monitors.
do you have a full can tool? or just a near useless codereader.
?

Oct 15, 2013 | 2004 Jeep Grand Cherokee

1 Answer

Where is the o2 sensor on a 2004 blazer located


Removal & Installation

Raise and support the vehicle.
Support rear of the powertrain frame.
Remove four rear frame bolts.
Lower the frame no more than 73.2 mm (3 inches).
Disconnect the rear oxygen sensor electrical connector.
Remove the rear oxygen sensor from the rear exhaust manifold.

To install:

Install the rear oxygen sensor in the rear exhaust manifold. Tighten the rear heated oxygen sensor (HO2S) sensor to 41 Nm (30 ft. lbs.).
Connect the rear oxygen sensor connector.
Raise the frame.
Install the four rear frame bolts. Tighten the frame bolts to 100 Nm (74 ft. lbs.).
Lower the vehicle.


Heated Oxygen Sensor Bank 1 Sensor 1 (HO2S 1/1)

WARNING: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_39_03_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 1

Heated Oxygen Sensor Bank 1 Sensor 2 (HO2S 1/2)

CAUTION
Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_40_07_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 2

Raise and support the vehicle.
Remove the heat shield.
Disconnect the heated oxygen sensor electrical connector.
Remove the heated oxygen sensor.

To install:

Install the heated oxygen sensor. Tighten the heated oxygen sensor (HO2S) to 41 Nm (30 ft. lbs.).
Connect the heated oxygen sensor electrical connector. CAUTION
Ensure connectors are securely installed beneath harness heat shield to prevent damage.
Install the heat shield.
Lower the vehicle.


Heated Oxygen Sensor Bank 2 Sensor 1 (HO2S 2/1)

CAUTION: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

Raise and support the vehicle.
Remove the air deflector.
Disconnect the front oxygen sensor electrical connector.
Remove the front oxygen sensor from the front exhaust manifold.

11_14_2011_1_37_39_pm.jpg

Fig. Showing the location of the HO2S Bank 2 Sensor 1

To install:
Install the front oxygen sensor in the front exhaust manifold. Tighten the front HO2S sensor to 41 Nm (30 ft. lbs.).
Connect the front oxygen sensor electrical connector.
Install the air deflector.
Lower the vehicle.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 14, 2011 | Cars & Trucks

1 Answer

Location of oxygen sensor on 2004 blazer check engine light keeps coming on. Replaced sensor no change. At bank 1 sensor is not connected when tested.


Removal & Installation

Raise and support the vehicle.
Support rear of the powertrain frame.
Remove four rear frame bolts.
Lower the frame no more than 73.2 mm (3 inches).
Disconnect the rear oxygen sensor electrical connector.
Remove the rear oxygen sensor from the rear exhaust manifold.

To install:

Install the rear oxygen sensor in the rear exhaust manifold. Tighten the rear heated oxygen sensor (HO2S) sensor to 41 Nm (30 ft. lbs.).
Connect the rear oxygen sensor connector.
Raise the frame.
Install the four rear frame bolts. Tighten the frame bolts to 100 Nm (74 ft. lbs.).
Lower the vehicle.


Heated Oxygen Sensor Bank 1 Sensor 1 (HO2S 1/1)

WARNING: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_39_03_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 1

Heated Oxygen Sensor Bank 1 Sensor 2 (HO2S 1/2)

CAUTION
Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_40_07_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 2

Raise and support the vehicle.
Remove the heat shield.
Disconnect the heated oxygen sensor electrical connector.
Remove the heated oxygen sensor.

To install:

Install the heated oxygen sensor. Tighten the heated oxygen sensor (HO2S) to 41 Nm (30 ft. lbs.).
Connect the heated oxygen sensor electrical connector. CAUTION
Ensure connectors are securely installed beneath harness heat shield to prevent damage.
Install the heat shield.
Lower the vehicle.


Heated Oxygen Sensor Bank 2 Sensor 1 (HO2S 2/1)

CAUTION: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

Raise and support the vehicle.
Remove the air deflector.
Disconnect the front oxygen sensor electrical connector.
Remove the front oxygen sensor from the front exhaust manifold.

11_14_2011_1_37_39_pm.jpg

Fig. Showing the location of the HO2S Bank 2 Sensor 1

To install:
Install the front oxygen sensor in the front exhaust manifold. Tighten the front HO2S sensor to 41 Nm (30 ft. lbs.).
Connect the front oxygen sensor electrical connector.
Install the air deflector.
Lower the vehicle.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 12, 2011 | Cars & Trucks

1 Answer

My 2004 sedona has little power going up hills, my local machanic says the code( po431) means the bank 2 catyletic converter is bad, but which converter is bank2? also have a code -p01159 which no one...


The answer to your first question is the Oxygen sensor bank 2. Its the oxygen sensor after the catalytic towards the rear of the motor. For the other DTC there is no P01159 DTC, P0159 is Bank 1 Sensor 1 Oxygen Sensor bad, P1159 is an air intake leak or a MAF (Mass Air Flow Sensor leak)

Jul 06, 2011 | 2004 Kia Sedona

1 Answer

I need a diagram of the exhaust system on a Mazda 626


0996b43f80203328.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2000 MPV

1 PCM 2 Mass air flow (MAF)/intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Fuel tank pressure sensor 5 Engine coolant temperature (ECT) sensor 6 Crankshaft position (CKP) sensor 7 Camshaft position (CMP) sensor 8 Knock sensor 9 Heated oxygen sensor (HO2S) (front, LH) 10 Heated oxygen sensor (HO2S) (front, RH) 11 Heated oxygen sensor (HO2S) (rear, LH) 12 Heated oxygen sensor (HO2S) (rear, RH) 13 EGR boost sensor 14 Power steering pressure (PSP) switch 15 Main relay


0996b43f8020330c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart-2001 MPV

1 PCM 2 Mass air flow (MAF)/Intake air temperature (IAT) sensor 3 Throttle position (TP) sensor 4 Engine coolant temperature (ECT) sensor 5 Crankshaft position (CKP) sensor 6 Camshaft position (CMP) sensor 7 Knock sensor 8 Heated oxygen sensor (HO2S) (front, LH) 9 Heated oxygen sensor (HO2S) (front, RH) 10 Heated oxygen sensor (HO2S) (rear, LH)* 11 Heated oxygen sensor (HO2S) (rear, RH)* 12 EGR boost sensor


0996b43f8020330f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Component Location Chart- 2002-06 MPV

May 22, 2010 | 2004 Mazda MPV

1 Answer

What is the location ofttgen sensor, bank 2


Its located in the exhaust manifold on the passenger side,its the sensor closest to the rear of the engine.

Feb 07, 2010 | 2004 BMW 3 Series

3 Answers

Were on exaust is oxygen sensor in 1999 subaru impreza auto sport


On the SOHC engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the front catalytic converter. On the DOHC engine the front oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the catalytic converter.

Oxygen sensor location-Baja 2.5L SOHC engine
c3fce0b.jpg

Oxygen sensor location-Baja 2.5L DOHC engine
7aac75e.jpg


On the 2.0L engine the front (A/F) oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the rear catalytic converter. On the 2.2L engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the rear catalytic converter.

Oxygen sensor location-Impreza 1998-2001 2.2L engine
a5973e4.jpg


moz-screenshot.pngOxygen sensor location-Impreza 1998-2002 2.5L SOHC engine
3a84717.jpg
I hope helped with this; remember rated this help. Good luck.

Nov 20, 2009 | 1999 Subaru Impreza

1 Answer

Oxygen sensors in a 2004 dodge ram 1500 4x4


im not for sue how many but u need to take it to autozone if u have one where u live they will tell u where it is the most comon one if u have straight eguast is the one right in front of the cats if its that one u should notice a stall out every time u fill up from below empty on ur gauge

Mar 16, 2009 | 2004 Dodge Ram 1500

Not finding what you are looking for?
2005 Chevrolet Avalanche Logo

Related Topics:

78 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...