Question about 1995 Audi A6

2 Answers

My infrared remote does not work. I have an Audi A6 1995

My infrared remote does not work. I bought a new pair of car keys. I have an Audi A6 1995 and in the internet I only have found the procedures for reprogramming the wireless fob, not the IR one. How can I reprogram it?

Posted by on

  • Flavio Fraga Mar 25, 2009

    No. This solution is available in the owner´s manual. It did not work.
    I wonder if there is any device in the car that is not receiving the IR signals... or is just the way to reprogram the alarm that is not being correctly described in the internet...
    Thank you anyway.


×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Do you have memory seats as well? If so follow these steps I am going to refer to the keys as A and B as you have 2 of them
1) Unlock car with key A
2) Turn ignition into ON position with key A and roll down the window
3) Point Key B at IR Sensor and Click twice (perform both clicks under 5 seconds)
4) Turn off ignition and pull Key A out
5) Turn ignition into ON position with Key B
6) Point Key A at IR Sensor and Click once
7) Turn off ignition and Pull Key B out

Key A should be programmed as the Master Seat Program and Key B should be programmed for the Secondary seat program
So when you set your memory seats Key A is for Memory Position 1 and Key B is for memory position 2
if you don't have memory seats then you only have to point the receiver at the sensor and click once. That should just sync the IR Frequency and Codes

Posted on Mar 08, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Please my friend... my e-mail is: turbofort@bol.com.br I need a new pair of keys to my audi a4 1995 with infrared alarm... Where i can bought this keys ?? Please, help me. Thank you, and sorry my english !!!

Posted on Jul 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Programming 2000 Audi A6 Quattro Remote Key


An Audi dealer may be able to help.

Jan 09, 2014 | Cars & Trucks

1 Answer

Reset keyfob


Sounds to me like the key needs to be programmed to the car by the dealer. I would take it back there and get them to program it for you.

Sep 26, 2013 | Audi Cars & Trucks

1 Answer

I have a 1996 audi a4 and have bought an OEM remote from my dealership. I did the two key thing and holding remote buttons but it did not work. They checked my vin and said it was the right part, but it...


You'll need two keys.
1) Open the driver door, turn the ignition switch to on, but do not start the car.
2) Close and lock the driver door with the other key (this should be the proper key and not just the valet key - if you use the valet key the programming won't work).
3) Hold down both buttons on the fob for about 5 seconds. The lights should flash and the alarm horn should honk.
4) Open the door, remove the key from the ignition. Close and lock the door with the key.

hope this helped if not then I would go to the back to the dealer and have them do it for you.

Oct 16, 2010 | Audi A4 Cars & Trucks

2 Answers

Key/FOB programming


Jaguar X-Type Programming (Pairing) a Remote KeyFob X-Type 2.0, 2.5 and 3.0L

keyfob.jpg

Programming or pairing a new remote Keyfob for the X Type is a very simple job that will cost a substantial amount if it is done by Jaguar. It's annoying but this may need to be done if your Keyfob battery has been allowed to go flat, or the car battery has been removed for any length of time.
Follow these steps exactly and you should have no problems, pairing old or replacement Keyfobs for your car.

1.)I would recommended that you ensure all key fobs are fitted with new batteries. ( Click here to see battery replacement guide).
2.)Get in the car and close the drivers side door.
3.)Put the key into the ignition and turn to position I.
4.)Wait 5 seconds
5.)Turn the key quickly to position II then back to I four times.
6.)You should hear a single chime.
7.)Remove the Key
8.)For each Keyfob in rapid succesion. Press any single button on the keyfob you wish to pair, you should hear a chime as each Keyfob is paired with the security system. After the chime do the next Keyfob.
9.)Check operation of each Keyfob.

May 19, 2009 | 2005 Jaguar X-Type

1 Answer

How do you program a keyless remote for a 2000 audi tt


It needs to be adapted using dealer scan tool or if you know someone with VAGCOM.  Make sure you have all your remotes.  When performing this.  

Apr 30, 2009 | 2000 Audi TT

2 Answers

Audi tt remote won't work, i,ve tried everything


The remotes have to be readapted by a dealer scan tool or someone who has Vagcom.  Make sure you have both keys when doing this.  If adaption doesn't take then there is a good chance the remote/s are bad.

Apr 07, 2009 | 2001 Audi TT

3 Answers

2003 Tiburon GT Remote Key


Seriously don't use the factory alarm system / keyless entry.

While my car was under warranty, the alarm malfunctioned and it wouldn't disarm. The solution was to have the car towed to a dealership and install a new BCM. This would have cost me over $1,000 - and it's not an isolated case.

Don't get a Hyundai key fob. Have an after market alarm / keyless entry installed. It will be cheaper & easier.

Jan 06, 2009 | 2003 Hyundai Tiburon

Not finding what you are looking for?
1995 Audi A6 Logo

1,365 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

61249 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13160 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...