Question about 1995 Mercury Villager

1 Answer

95 mercury villager

I have changed the battery , plugs, wires(in order) but Stupid me when jumped the vehicle with old battery i crossed the poles on the battery. Now with the new baterry I can not even get the vehicle to turn over, is the a specific fuse or some thing i may have fried ? any help would be appreciated

Posted by on

  • pjaju52 Feb 17, 2009

    that didnt do it, let me add i have no power ,lites horn anything.

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Mercury Master
  • 783 Answers

Check fuse 26(10 amp) in the instrument panel fuse box.

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why is there a loss of power on a 1993 mercury villager after engine gets warm


Very old vehicle, and highly likely it needs a new fuel filter and major tune-up (including all new spark plug wires, spark plugs, cap, rotor, and ignition coil).
Verify proper fuel pressure at the fuel rail, and service fuel pump and fuel pressure regulator as necessary. If you have been using ethanol blend fuel in the vehicle over the past few years, I recommend removing ALL FUEL from the vehicle and replacing it with new. Please read my "Tip" on Fixya regarding the problems with ethanol blend fuels in older vehicles (such as yours).

Aug 02, 2012 | 1993 Mercury Villager

1 Answer

When warm runs rough sets knock sensor code will hardly idle turn front cat cherry red car sat for a year put new gas in it when cold runs great


If the cat is cherry red as you say it is I would check the firing order or timing they may have crossed plug wires this will cause the exhaust manifolds to get red hot and glow let me know if this heled you and good luck.It definitely sound to be timing related or crossed wires.

Feb 09, 2011 | 1999 Mercury Villager

1 Answer

My 95 mercury villager just stopped while i was pulling out of driveway and now it will not turn over.Is there a fuse or something.


check battery cable connections, especially the 2 smaller wires on the positive post. Clean them.

Aug 16, 2010 | 1995 Mercury Villager

1 Answer

Just aquired A Ford Mercury Villager 1998 any suggestions as to stores for spares ie servicing Brake Pads, etc


On the villagers the front motor mount alot of the time is bad on these vehicles.Change the oil every 3,000 miles.Also check the air cleaner and the battery terminals and make sure they are clean if not clean them with like some 100 -150 grit sandpaper on the battery cables the positive and negative wires and also clean the battery post where the cables hook up to.

Apr 01, 2010 | 2000 Mercury Villager

1 Answer

95 mercury villager v.6 jolts when entering first


you need to disconnect the battery for 2 hours to clear the computer memory so it can relearn the new engine.
Also, adjust the TP, throttle position sensor with volt meter or ohm meter. clean MAF sesnor with carb cleaner.

go here for more help with villager

http://groups.yahoo.com/group/villagerquest/

Jan 12, 2010 | 1995 Mercury Villager

1 Answer

No start


It sounds like you need to clean both battery cable connections on the battery and make sure they are not spread. You may have to cut off steel clamps and replace with lead kit. Also, clean the 2 smaller wires on the poitive post of the battery.

Go here for more help. We fix all Villagers with our expertise. Nothing we can't fix. Free too!

Jul 23, 2009 | 1995 Mercury Villager

2 Answers

How to change a headlight bulb on my 95 villager


1.- Carefully unplug the wires connected to the bulb located inside the headlamp, be sure to glently press the far side of the plug (where the wires come out) there's a rectangular shaped lock and pull the plug.
2.- Carefully turn the donut ring that holds the bulb in its position by turning it about 1/4 turn counter clockwise and pull it out.
3.- Pull the bulb out gently (never touch the glass) just the plastic base.
4.- Place the new bulb inside and be sure it is in the same position as the old one.
5.- repeat step 2 and 1 backwards.
There should be no problem

Jul 11, 2009 | 1995 Mercury Villager

1 Answer

Headlights don't work


Try replacing the bulbs in the sealed beam. Bulb #9007, do both. Lift lid, disconnect electrical wires, unlock o ring, pull out bulb. Replace bulb and reverse the order

Dec 03, 2008 | 1995 Mercury Villager

Not finding what you are looking for?
1995 Mercury Villager Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...