Question about 2003 Chrysler Town & Country

2 Answers

How do I change the brake light in my 2003 Chrysler T&C?

I can't figure out how to remove the red cover to get to the bulb.

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Once the liftgate is open, on the inside next to the tail light assembly, you'll see two black knobs. There are no screws involved, but you will need a regular screw driver and pliers. You need to gently pry or pull these two knobs outwards. Once these knobs are dislodged entirely, the assembly should easily come off. Brake bulb #3057 is the replacement. Good luck.

Posted on Feb 24, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 547 Answers

Look inside trunk

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both brake lights out on 2003 Lexus RX 300


does the third brake light work? If so change bulbs on lower lights by removing cover then taking out bulb. It twists out. Simple.

Dec 23, 2010 | 2003 Lexus RX 300

1 Answer

I can't figure out how to get my 2003 Tundra taillight assembly off . I have removed the two bolts inside the tailgate area but it is still attached to the fender on the other side of the assembly . I have...


Unscrew the screws that are securing the brake light cover to the body of the Tundra. Pull the brake light cover off the body of the Tundra. Place the screws in the brake light cover and set it on the bed of the truck. Pull the burned-out light bulb out of the light fixture and discard it. Insert the new brake light bulb into the light fixture. Pump the Tundra's brakes to make sure the new bulb is working correctly. Replace the brake light cover on the body of the Tundra and replace the screws.

Sep 09, 2010 | 2003 Toyota Tundra

1 Answer

Rear brake light went out. How do I open cover to


In order to replace the bulb you need to remove the pad from the inside the car where the light located ,once you remove the pad you able to reach the light holder replace the bulb fix the pad the again ...

Good luck ....

Sep 30, 2009 | 2003 Subaru Outback

1 Answer

How do I change the rear break light?


How to Replace a Tail, Brake or Reverse Light writer_avatar.gif Contributor By eHow Contributing Writer Article Rating: stars_3_20.gif (70 Ratings) replacelight_hero.jpg Fix that broken tail light. Replacing a dead bulb on your car is almost as easy as replacing a light bulb at home. Perform this simple maintenance and avoid the hassle of receiving a citation for a missing brake lightmag-glass_10x10.gif.
jQuery('.intro .thumbnail').each(function(i,e){ jQuery(e).find('img').one('error',function(){ jQuery(e).remove(); }); }); Difficulty: Moderately Easy Instructions Things You'll Need:
  • Rubber Gloves
  • Automotive Light Bulbs
  • Red Tape
  • Cleaning Cloths
  • Rags
  • Screwdriver Sets
  1. Step 1 Determine how the bulb is accessed: On some models the lens (the red or white plastic part over the light) must be unscrewed from the outside, and on others the bulb is accessible only from inside the trunk. If there are no screws on the lens, you can assume that the bulb must be replaced from inside. Usually there will be a plastic cover that must be removed in order to access the bulb. There may be tabs, screws or small knobs that hold this plastic cover in place.
  2. Step 2replacelight_2s.jpg Unscrew the lens on the outside, or take off the plastic cover from inside the trunk, to reveal the bulb.
  3. Step 3replacelight_3s.jpg Unscrew the bulb. You'll have to push in and turn at the same time.
  4. Step 4 Take the bulb with you to the auto supply store to help you find an exact duplicate.
  5. Step 5replacelight_5s.jpg Clean the connection with a wire brush and/or wipe it clean with a rag if there's any corrosion.
  6. Step 6replacelight_6s.jpg Screw the new bulb into the empty socket. Again, you'll have to push in and turn simultaneously. Line up the tiny raised bumps on the base of the bulb in order to screw it in.
  7. Step 7 Replace the lens or the plastic cover.
  8. Step 8replacelight_8s.jpg Test your work by stepping on the brakes and turning on the headlights while a friend watches the new bulb to make sure it lights up.
  9. hope this will help you

Jul 20, 2009 | 2005 Chrysler Pacifica

1 Answer

Brake light cover wont come off?


you have anouther screw inside on piller.

May 27, 2009 | 2003 Isuzu Axiom

1 Answer

How do I change the brake light and signal in 2005 town country


Open the tailgate and on either side you'll see 2 screws holding the tail light assembly. Unscrew these and the assembly will come off. It might take a little prying if it has never been removed before. Each bulb is in a base attached to the assembly from the back. Turn the base 1/4 turn and pull out to get access to the bulb itself.

Feb 14, 2009 | 2003 Chrysler Town & Country

1 Answer

Bulb repair....


Hi my name is Allen!

Here is how to change the brake light bulbs, first pull the carpet down that runs up the back covering where the light assembly is installed, next grab the wing nuts, they are black in color, they are designed so you can turn them with your fingers, remove all of them, then pull straight out with the brake lamp assembly.

After the assembly is removed, grab the socket on the back with the wires coming out of it and turn it counter clockwise and pull it straight out, then grab the bulb and pull it straight out and push the new one back in, that's it.

For further assistance contact me at FixYa!

Jan 01, 2009 | 2001 Chrysler Sebring

1 Answer

How do I change the back brake light of a Hyundai Elantra?


If it is the light in the rear window, there are two plastic caps on either side on the base of the light. Pop off the cap and remove the screws inside. That should allow you to get to the bulb. I went to autozone for the bulb w/o removing it and they gave me the wrong one. If you have the bulb removed, you're better off, if not, the people at advanced got me the correct one without any issues. If it's the brake lights on the back of the trunk, you access those from inside the trunk. On either side, there are thumbscrews (sometimes under the fabric lining flaps). Once you remove the bulb carrier, you'll know which one is out. It usually lines up with the red cover but if you can borrow someone's time, have them look in your trunk at the bulbs as you test your parking lights to see which one lights and which one doesn't. Hope this helps.

Dec 10, 2008 | 2000 Hyundai Elantra

Not finding what you are looking for?
2003 Chrysler Town & Country Logo

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...