Question about 2004 Jeep Grand Cherokee

1 Answer

Automatic door locks

Auto. door locks only work if I start engine before closing drivers door.
if I close door first, door locks will not lock(15mph) how come????

Posted by on

  • brower15 Feb 20, 2009

    wiring all looked good

  • Anonymous Mar 16, 2014

    drivers door lock only works when door is closed

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 33 Answers

The major complaint with that model is the wire loom to the driver door doesn't have enough slack in it. if you pull the black wire cover back from the door you should be able to see ware and tares ( in mine it was the black and an ornge wire broken ) patch your problem wires and then what i did was if you take the kick panel off the inside you can follow the wires to a plastic clip attached to a bolt and take it off the bolt to give the wires a little more play.
I hope this is sufficiant, if not let me know and ill look deeper in to it. Thank you

Posted on Feb 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why does my doge caravan doors lock when u start to warm it up as soon as you close the door you get locked out. Or when u have it started as soon as driver door closes the whole van locks?


You must have a "After Market Alarm" or something similar. The factory Auto door lock system doesn't lock the doors until the vehicle reaches 18 mph approximately.
So what I am saying is the Add-On Door Lock/Alarm System is malfunctioning - however some of those aftermarket systems can be programmed to lock doors with the engine running and Driver's door closed (they assume you will be sitting in the driver's seat at that time) It varies depending on which manufacturer built the system. I have seen on some of those systems they provide a small loopwire on the Module that can be cut to disable the Auto Door Lock feature - you might need the install manual to know which one.

Feb 20, 2015 | Cars & Trucks

1 Answer

Opening the drivers door doesnt automatically open the passangers door


Some vehicle locking systems allow a single button press to unlock the driver's side door and require a second button press to unlock the passenger side door. Likewise, use of the key to unlock the driver's side door does not automatically unlock the passenger side.

Mar 25, 2014 | Dodge Stratus Cars & Trucks

1 Answer

Doors lock automatically


put blank spare in the wallet , thieves love easy to find spare keys.
i even cut the heads off keys (hacksaw) so the end part fits in my wallet. no plastic bulge. wife has purse, so can carry bricks easy.
done this for 50years of driving.
my jeep does this and is a feature, but is reset at door exit.
my jeep locks above 15mph. and is programmable.
so did you read your operators guild on this?
so RTM, first.
or reset the system.

Feb 06, 2014 | Honda Odyssey Cars & Trucks

1 Answer

Automatic door lock 1999 toyota prerunner


hi jerome
I have the procedure for Toyota auto lock, is worth to try it
AUTOMATIC LOCK SETTING
1) Step in the vehicle and make sure that all doors are closed completely
2) Insert the key into the ignition key cylinder.
3) Wait for more than 5 seconds.
4) After turning the key to the ACC position, turn the key from the ACC to the
ON position 5 times within 10 seconds (Last position : ON).
? Status Monitor LED will illuminate for 30 seconds.
Note : In case you implement 6 times or more by mistake,
action steps 6)-8) you made will be canceled.
Please retry from step 2).
5) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key to the ACC position.
? LED will continue illuminating.
? Indicator lights will flash 2 times.
Ignition controlled door lock ON :
6) While the LED is illuminated:
• Open and close the driver's door 1 time.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 1 time.
? LED will extinguish.
Ignition controlled door lock OFF :
6) While the LED is illuminated :
• Open and close the driver's door 2 times.
• Turn the key ACC-ON-ACC 1 time (Last position : ACC).
? Indicator lights will flash 2 times.
? LED will extinguish.

Jan 28, 2014 | Toyota Camry Cars & Trucks

1 Answer

Coding spare key for a Toyota Echo?


Adding key.
Note:
You must be having one working master key to perform this function.
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted.
C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.

Jan 09, 2013 | 2001 Toyota Echo

1 Answer

Key buttons will not operate locking system,i have changed battery but still no good.use master key,gets me into the car but alarm goes off and also when i attempt to drive it.


I have the same problem kinda. Lost my master key and sent my ecu off with a home made 2 button key to program immobiliser. This key works to start the engin and drive but I cannot get the key to program with the alarm and locking system. You can try the following steps as may work for you.

I can get my car into programming mode after step 1 but step 2 does not work for me. The locks do not go off at all, not once or twice. Battery in remote key is fine as LCD lights red.

Can anyone help please?

Toyota celica 2000 - 2005 remote keyless entry programming guide
STEP 1
1. Key out of the ignition. Open the drivers door , all other doors are closed . Driver door is unlocked

2. Perform these steps within 5 seconds
a. Insert the key into the ignition ( do not turn it ) take key out
b. Insert the key into the ignition ( do not turn it ) take key out

3. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Insert the key into the ignition ( do not turn it ) and pull it out.

4. Perform these steps within 40 seconds
a. Close and then open the drivers door.
b. Close and then open the drivers door.
c. Close drivers door.
d. Insert the key into the ignition and leave it in the ignition.
Turn the ignition to on (as far as you can go without turning the engine over ), then back to off .
e. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.

STEP 2 (Does not work for me)

6. Perform these steps within 40 seconds
a. Press the lock and unlock buttons on the transmitter simultaneously for 2 seconds
b. Immediately after letting go of the lock and unlock buttons, press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock then unlock once indicating successful programming. If the door locks cycle twice, repeat steps 6a and 6b as the remote was not accepted.

7. Open drivers door

Hope this works for you.
Hayley

Oct 03, 2010 | 2000 Toyota Celica

1 Answer

2003 toyota camry how do you reset wireless entry remote


if remote is good here are the factory instructions to program it, if this doesn't work u may have a bad remote or receiver in car.

1. Start with the key out of the ignition, drivers door is open all others closed and
drivers door is unlocked.

2. Perform these steps within 5 seconds.
A. Insert the key into the ignition(Do NOT Turn) Pull key out.
B. Insert the key into the ignition(Do NOT Turn) Pull key out.

3. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into the ignition(Do NOT Turn) Pull key out.

4. Perform these steps within 40 seconds.
A. Close then open the drivers door.
B. Close then open the drivers door.
C. Insert the key into ignition and leave it in ignition.
D. Close the drivers door.
E. Turn the ignition to ON (Do NOT Start) then back to OFF.
F. Remove the key from the ignition.

5. Within 3 seconds, the power door locks should lock then unlock automatically
indicating successful entry into programming mode.
Return to step 1 if the locks do not cycle at this point.

6. Perform these steps within 40 seconds.
A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds.
B. Immediately after letting go of the lock and unlock buttons,
Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door
locks should lock and then unlock once indicating successful programming. If
the door locks cycle twice, repeat steps A and B in step 6 as the remote was
not accepted.
C. Repeat steps A and B in step 6 for each new remote.

7. Open drivers door.

Sep 09, 2009 | 2002 Toyota Corolla

1 Answer

Drivers Door Window/Locks aren't working


driver side lock and window switch... if its all one unit... i had a 95 cherokee laredo that did that... changed the switch and it fixed my problem...

Mar 15, 2009 | 2003 Jeep Grand Cherokee

2 Answers

Automatic door locks


Look in rubber casing at hinge of door for broken wire.

Jan 18, 2009 | 2004 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...