Question about 1999 Oldsmobile Cutlass
Between the fuel tank and the rear tires. Right in the center of the car. Pull the fuse for your fuel pump, run the car until it dies, loosen the fuel line on one end, then there is a clip at the other end take that off, and you done.
Posted on Apr 12, 2009
Working on Mom's car for three days now I've just about pulled all my hair out ! The dam thing would bog as i tried to accelerate over 700 RPM. We replaced the MAP,TPS,FUELPUMP,and i ohm-ed out everything under the hood, and then i found it!! The CRANK POSITION SENSOR had cracks around the base of the sensor and had oil seeping out.Check out pic.I hope this could be of some help...
Posted on Mar 09, 2009
the fuel filter on this car should be near the rear of the car in front of the tires and it should have screw in lines on it i believe a 5/8 wrench and 3/4 wrench should be able to remove the lines then you have to undo the bracket that holds it in place not sure what size this is.
Posted on Aug 24, 2009
Fuel filters are easy to replace but let me give you some friendly warnings:
CAUTION. To reducethe risk of fire and personal injury always follow the correct procedure for disconnecting and connecting fuel pipe quick connect fittings. This will ensure good connections and prevent possible fuel leaks.
CAUTION. Safety glasses must be worn if you use compressed air, as flying dirt prticles may cause eye injury.
The fuel filter is no longer serviced in regular maintenande intervals. It is only necessary to replace the fuel filter in the case of damage or a clogged filter.
Before replacing a fuel filter it is necessary to relieve fuel system pressure.
Your fuel filter is located under the vehicle, driver side, below seating area, front of fuel tank, mounted on frame rail in fuel line
Fuel filters and elements are serviced by replacement only. Some vehicle manufacturers recommend fuel filter replacement at 30,000 miles (48,000 km). Always replace the fuel filter at the vehicle manufacturer's recommended mileage.
The fuel filter replacement procedure varies depending on the make and year of the vehicle and the type of fuel system. Always follow the filter replacement procedure in the appropriate service manual. The photo sequence below shows a typical procedure for relieving fuel pressure and removing a fuel filter.
Removing a Fuel Filter on an EFI Vehicle
Disconnect the negative cable at the battery.
Loosen the fuel tank filler cap to relieve any fuel tank vapor pressure.
Wrap a shop towel around the Schrader valve on the fuel rail and remove the dust cap from the valve.
Connect the fuel pressure gauge to the Schrader valve.
Install the free end of the gauge bleed hose into an approved gasoline container, and open the gauge bleed valve to relieve the fuel pressure.
Place the vehicle on the hoist and position the lift arms according to manufacturer's recommendations. Then raise the vehicle.
Flush the fuel filter line connectors with water, and use compressed air to blow debris off and away from the connectors.
Follow the recommended procedures for disconnecting the fuel inlet connector.
Art courtesy of Delmar - Thomson Learning.
Follow the recommended procedures for disconnecting the fuel outlet connector, then remove the fuel filter.
Installing Fuel Filters
In-line fuel filters are installed in the fuel line. In carbureted engines, the in-line gasoline filter is usually installed between the fuel pump and the carburetor. In vehicles with a fuel injection system, the location of the fuel filter is determined by the manufacturer. An arrow on the filter shows the direction of fuel flow.
Posted on May 22, 2011
Tips for a great answer:
Mar 31, 2011 | 1992 Oldsmobile Cutlass Supreme
Feb 03, 2011 | 1995 Oldsmobile Cutlass Ciera
Aug 10, 2010 | 1993 Oldsmobile Cutlass Ciera
Jul 12, 2010 | 1985 Oldsmobile Cutlass Supreme
Mar 04, 2010 | 1993 Oldsmobile Cutlass Ciera
Feb 03, 2010 | 1991 Oldsmobile Cutlass Supreme
Jan 13, 2010 | 1995 Oldsmobile Cutlass Ciera
Aug 22, 2009 | 1993 Oldsmobile Cutlass Supreme
311 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: