Question about 1999 Chevrolet Silverado 1500

1 Answer

Remove inside door panel without breaking it

1998 siverado. drivers door inside handle broken. Can remove arm rest, window crank, and bezel panel around handle assy. A speaker is installed in doors (factory). How does one remove panel without destroying it? Store how-to manual sucks for guidance

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 75 Answers

They have push in clips that hold the panel on the door you can pull it off with your hand or go to parts store and buy a door panel removal tool
PLS take time to rate this solution and by the way you will probably need to buy new push in clips to hold panel on

Posted on Feb 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove inner door panel from a 1979 MGB


The door handle bezel is a two-piece plastic surround that pinches the door panel tight there at the handle. That is the tricky part, push in on the panel and up on the upper half and down on the lower half of the bezels to remove them, as they slide out when pressure in taken off them. The rest of the door panel is 2 screws holding the arm rest on and on in the window crank, then the edges are held in place by hidden snaps - just pry the panel away from the door carefully as close to the clips as you can get. Just feel where the panel is tightest to the door to locate them.

May 12, 2012 | MG B Cars & Trucks

2 Answers

How to remove a door panel in a 2001 buick


On the inside trim, you can remove screws (these screws may be covered by filler pieces or may be visible, or they may require you pry a plastic piece off that covers the screws) that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Jun 21, 2010 | 2001 Buick LeSabre

1 Answer

HOW TO CHANGE EXTERIOR DRIVER DOOR HANDLE


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then pull back the weather seal and disconnect the linkage to the outer handle and remove the bolts holding the handle onto the door

Oct 21, 2009 | 1998 Toyota Corolla

1 Answer

Want to change broken door handles ford escort 1998


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Now you can replace the interior door handle. If it's the outer door handle, pull back the weather seal and disconnect the rod to the outer handle and then unscrew the handle from the door.

Oct 01, 2009 | 1998 Ford Escort

1 Answer

Broken driver side door inside handle, how do I take off the door panel on a 2000 Chevy 3500 old body style?


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls.

Sep 27, 2009 | 2000 Chevrolet 3500

1 Answer

Avalon door panel


Below are the removal procedures for your vehicle's front inner door panel.


On models without power windows, remove the snap ring retaining window crank handle. Remove crank handle and cover plate.
Remove lower door frame bracket garnish. Using a screwdriver, remove inside door handle bezel. Remove power mirror control switch and disconnect harness connector.
Remove armrest panel. Remove 6 screws. Pry interior door panel loose from door.

May 23, 2009 | 2001 Toyota Avalon

1 Answer

Driver side door mechanism


Can you open the door with the inside handle? If you can, the problem is probably a broken plastic fitting inside between the outside handle and the door latch. There are door panel removal tools available at your local parts store that look like short handled wide bladed pry bars. You could get by with a good stiff putty knife if needed. Take off the arm rest, window crank, and speaker grill if you have aftermarket speakers. Slide the door panel removal tool under the edge of the door panel and CAREFULLY pop the clips loose from the door frame. You could always leave the window open and do the "Dukes of Hazard" thing, but then you would have to change the paint scheme.

Apr 15, 2009 | 2000 Suzuki Esteem

1 Answer

Need to replace a broken side mirror (power) on 1998 Pontiac Trans Sport how do I do this


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Feb 18, 2009 | 1998 Pontiac Trans

1 Answer

Door Panel removal


remove all visable screws from panel and arm rest. Arm rest should come off. Use a flat thin tool or piece of metal and slip it between the panel and the metal door frame. Slip it in about 2 inches,. Slide it back or forth til you hit a stop. That should be a plastic pop in.twist metal tool to pull panel away from the door. It should pop away from door frame. Don't overdo it if it doesn't come out. try another spot. once you get one loose, you can tell how to get the others out. Once panel is loose push it upwards to get top lip out of window bottom. If it has power windows,disconnect plug. If it has manual windows, you will have to remove the window crank There is a snap ring behind window crank that has to be removed.push in on panel by window crank and you can see the ring.

Dec 06, 2008 | 1998 Chevrolet Blazer

1 Answer

My driver's side window will now roll up how do I fix it?


most likely the window regulator has broken inside the door and will need to be replaced as well as the regulator handle. To remove them you will need a basic metric socket set, screwdrivers, and a rag or shop towel. start by moving the rag back and forth behind the window crank in order to remove the retaining clip. then once removed pull the crank from the splines of the window regulator.now undo the screw in the door handle press forward on the handle to release it from the door then undo the lock rod clip and remove the handle. there should be two large phillips head screws below the arm rest remove these. gently slide a flat bladed screwdriver under the bottom edge of the door panel. prying up to remove the retaining clips used to fasten the panel to the door. if you break the clips you can get replacements at most auto parts stores in their help section. Next lift the door panel up while lifting the bottom edge away from the door to remove the door panel. once inside the door you will need to lift the window up to gain access to the two 10 mm bolts attaching the regulator to the glass. undo the regulator retaining bracket and retaining bolts from the door. remove the regulator an assistant can be helpful to hold the glass up while you remove the regulator. installation is the reverse of removal

Sep 13, 2008 | 1994 Geo Prizm

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

938 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...