Question about 1997 Mitsubishi Diamante

Open Question

How to replace 1997 mitsubishi diamante starter

Cant find the location on car and what tools do i need

Posted by on

  • Mark Egan May 11, 2010

    Follow the large + battery cable to the starter. If you come across a small relay/solenoid looking thing before you get to the engine, then keep following the large + cable until you get to the engine.

×

6 Suggested Answers

  • 5 Answers

SOURCE: Mitsubishi Diamante 1995 (2.5L) harmonic balancer...

you def will not be able to drive the vehicle with no balancer due to the fact that is the main source that runs all your belts...all you should need is a harmonic balancer pulley remover..

Posted on Dec 09, 2008

  • 68 Answers

SOURCE: 2001 Mitsubishi Diamante won"t start

try holding down the throttle all the way when starting (thinking it might be flooded from overpumping the accelerator)

remember the computer automatic puts a shot of fuel in the car when you try to start (no need to pump)

Posted on Feb 05, 2009

mohd_sikande
  • 1 Answer

SOURCE: 1997 mitsubishi diamante stereo code

need a radio code for a 1997 mitsubishi diamante

Posted on Jul 27, 2009

erietrack
  • 37 Answers

SOURCE: starter location and tools needed to replace

It is located under the car toward the front of the motor by the oil filter. Look for a metal cylinder like object with a big 4 gauge wire going to it. To change the starter you will need to disconnect the battery. Using a 15mm socket and entension remove the 2 starter bolts. You may have to remove the oil filter to get enough clearance to get the starter out. Some cars have a 13 or 15mm bolt on the back of the starter for extra support. If your's has this you will need to remove it.once you pull the start down remove the 8mm and 13mm bolts that connect the wires to the starter. Be careful not to let the starter hang from the wires as they will break. Install the new one in reverse.

Posted on Nov 07, 2008

  • 1 Answer

SOURCE: where is the starter located on a 2000 mitsubishi diamante?

SEND MY NEW PASSWORD ON MY EMAILL

Posted on May 15, 2009

  • 718 Answers

SOURCE: Need to replace the starter on the 97 mitsubishi Diamante, how hard is it to remove and replace ?

To replace the starter you need to;
) Note if you have an anti-thief system and now to reset it if the battery is disconnected.
) Note the radio station selections if they are not saved if the battery is disconnected.

Now
) Disconnected the GROUND connector on the battery.
) Disconnect the electrical cable on the battery.
) Remove the 2 bolts holding the starter on. Remove the harder one to reach first.
) Pull the old starter out.
) Insert the new starter.
) Replace the bolt. Insert the easier bolt first.
) Tighten the bolts.
) Replace the electrical cable.
) Reconnect the GROUND connector on the battery.
) Reset any radio, clock or anti-thief systems.
) Return old starter for a core charge refund.

Posted on May 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you take off the engine cover of a 2006 Buick La Cross? Cant locate spark plugs to change them with this cover on. Do I need a special tool to get it off?


no special tools required , but getting to the plugs is a lot easier from the under side of the engine on a hoist

Aug 10, 2016 | Buick Cars & Trucks

1 Answer

What would cause my jeep to click the faster I go in the front end


noise.
we cant hear noise here , ever.

get car serviced, by men that can hear, and find exact location
location is top first thing to do. exact location
we have electronic stethoscopes to find noise moving
not using tools like this, makes testing, very dangerous.
ill not tell you how we did this before $50 electronic tools.
not.

Mar 09, 2015 | Jeep Cars & Trucks

1 Answer

Location of computer


It's gonna be crammed up under the dash against the firewall. Most I've seen (1985 onwards) are up behind the glove box. Unless this car is gold plated, not worth the broken back and chance of zapping any new computer you manage to get for it. Or it needs a Kia specialty mechanic with correct tools etc.

Nov 29, 2013 | 2004 Kia Amanti

1 Answer

Where is the relay located


the relay located for what? for fuel pump?
--------
Ktag ecu programming tool

Sep 28, 2012 | 1996 Oldsmobile Bravada

1 Answer

Locate computer in my 88 mazda b2600


You can't check codes on this engine without a special scan tool.

Sep 07, 2012 | Mazda B2600 Cars & Trucks

1 Answer

How do i remove the tape / radio player. cant see any hole for special tools and what tools do i need to use?? VW Passat 1.9 TDI 1998


Welcome to FixYa.com Do you have the premium IV or V system ? If so, below is the location of holes to remove radio. Regards, Lee d4f9f93.pnga8e4424.png3928517.png

Aug 20, 2010 | 1998 Volkswagen Passat

1 Answer

Got audi a4 1996 diesel need to change cambelt but


A diesel uses a different procedure. You'll need a tool to hold the camshaft pulley parallel to the top of the cylinder head. The timing mark to set TDC for piston #1 is located on top of bell housing. The pointer must be aligned on the diamond cut on the flywheel. A VW/Audi setting bar tool #2065A is needed to lock the camshaft in position. Lock the injection pumpin position using the special lock pin (VW/Audi special tool no. 2064). Caution: If the drive belt is broken or has jumped time, do not attempt to lock the sprocket at this time!!! You will also need VW/Audi special tool no. VW210 to measure belt tension between camshaft sproket and injection pump sprocket. So good luck.

May 01, 2010 | 1996 Audi A4

2 Answers

How do i change a fuel filter on a 2001 f150


The clamps are just a secondary lock, special tools are needed to unlock the fuel lines.

Nov 05, 2009 | 2001 Ford F150 Styleside SuperCrew

1 Answer

Cant release spare tire from under car of 2002 mercury villager. no owners manual available.


Location of the spare tire and tools
The spare tire and tools for your vehicle are stowed in the following
locations:
Item Location
Spare tire Under the vehicle, just forward of
the rear bumper
Jack assembly Under the third row bench seat in
the tool bag
Removing the jack and tools
1. Lift the 3rd row seat cushion.
2. Remove the jack assembly from the bag under the seat.

Removing the spare tire
1. Open the liftgate, locate the U-shaped slits in the carpet, and flip up
the piece of carpet to expose the hex nut.
2. Insert the lug nut wrench on the
hex nut in cargo floor.
3. Turn the wrench
counterclockwise until tire is
lowered to the ground and the cable
is slightly slack.
4. Remove the retainer from the
spare tire. It may be necessary to
lift one end of the tire to disengage
the retainer

Jul 12, 2009 | 2002 Mercury Villager

2 Answers

BMW 318i serial number location


Look on the Door end on the Driver side door. There should be a Tag or Label with it there.

Jan 22, 2009 | 1994 BMW 3 Series

Not finding what you are looking for?
1997 Mitsubishi Diamante Logo

Related Topics:

610 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...