Question about 2003 Toyota Camry

2 Answers

Remove stereo from 2003 toyota camry

How do I remove the face plate of my factort 2003 toyota camry?

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

Simply take a small falthead screwdriver and wedge is carefully underneath the faceplate near the bottom and gently pry up and towards you. Slowly work your way around the bottom until the plate comes lose. Be careful not to yank it off because the cigarette lighter is still attachced. You can remove all off the faceplates connections once the plate is loose enough to see behind it.

Posted on Dec 27, 2012

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 3,051 Answers

Hi there :
if you remove the knobs you will see there is some flat nuts that need to be removed remoive them and there should be able to remove the faceplate

Posted on Feb 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove stereo from a 1990 toyota camry?


Go here: http://www.installdr.com/installdocs/toyota/camry.asp
Pick your year(s), which in your case will be the third one down, and follow the instructions. Frankly if you find these instructions intimidating have a professional install your new radio.

Jun 23, 2014 | 1993 Toyota Camry V6

1 Answer

How to remove Toyota camry 2003 front bumper bar


The video at this YouTube LINK outlines the bumper removal to change the headlights in this case.

Sep 07, 2012 | 2003 Toyota Camry

1 Answer

How do I remove the dash on my 1997 Rav 4 so I can get at the radio


This Toyota Rav-4 1998 to 2000 - Radio Installation / Stereo Installation coudl helped: InstallDocs/Toyota/PDF/869029.pdf

Good luck.

Jun 03, 2011 | 2003 Toyota Camry

1 Answer

Toyota fortuner LCD is blank while radio is working


Back light on lcd went out,need to replace back light bulb inside radio face plate.if no electrical exsperiance then i would take to radio shop.

Mar 07, 2011 | 2007 Toyota Camry

1 Answer

Need to remove speedometer cable from speedometer head


you will need to take out the instrument cluster. there will be a number of phillips screws that hold the face plate on

Feb 02, 2011 | 1991 Toyota Camry

1 Answer

I am looking for the fuse location for my license plate lights .I have a 2003 camry xl


if your headlights and taillights work its not a fuse try a new bulb or a new socket. turn the lights on with the enjine running and test the socket with a test light . if you have power replace the bulb

Nov 17, 2010 | 2003 Toyota Camry

1 Answer

1994 toyota camry blinkers flashing wen opening and closing the car doors the blinkers on both sides go off for about one minutes then stops simulating an alarm (the car previosly had an alarm but doesnt...


easiest repair is to remove pigtail connected between ign switcg and alarm dicard and plug factort harness back into ign switch hope this helps please rate

May 07, 2010 | 1994 Toyota Camry

1 Answer

How do I remove the struts on my 2003 toyota?


Basically the shock inserts in the struts are what hold the spring in place, and the axle knuckle to the fender.

On a very few cars, they were slick enough to design it so that you don't have to do very much.
On these exceptions, you just remove a plate from the top of the strut, in the engine compartment, and pull the insert up after unscrewing a cap.

But on most cars, you have to first drop the top of the strut down from the fender, then undo the pinch bolts at the bottom, in order to remove the whole strut from the car. Then you put a large spring compressor on it to remove the tension. (this is dangerous) You can rent or buy inexpensive spring compressors, because some are just a pair of threaded rods with hooks on both ends. Then you take the top plate off the strut by removing the nut threaded onto the insert shaft. Then there is a cap on the end of the strut tube, that allows the insert to be removed. The tube may be filled with oil. By accident if leaking, or be design with some cars, for cooling. Then you slip the new intsert in, cap it down, put the compressed spring back on, tighten up the top plate with the nut threaded on the shaft, uncompress the spring, and then place the strut back on the lower knucke, and finally back in the fender.

The difference between the fronts and rear is that the front may have an excentric bolt on the bottom, so that you can adjust the camber. If so, mark it before losening, so that you can put it back at the same angle of rotation. A chisel mark will do. The rear usually does not have alignment.

Feb 18, 2010 | 2003 Toyota Camry

1 Answer

The driver side door of my 2003 toota camry will


remove the door trim there are screws holding it then once they are removed pull on the trim to remove it from the door,you will find that the little motor(actuator is not working or come adrift or wiring you will be able to see it with the door trim off.It may just be it needs replacing and has broken

Nov 10, 2009 | 2003 Toyota Camry

2 Answers

I recently got pulled over for not having a tag light on my 1990 toyota camry but when i went back there to look there wasnt a spot for one. did i over look it ? is there a tag light for a 1990 toyota...


the light is located on the sides of the number plate,if you look to the sides of the reg plate you will see plastic covering the light you can remove it by opening trunk to see how to remove the cover on the back to get to the globe,its common for them to not work after time just need to replace the globes

Nov 09, 2009 | 1990 Toyota Camry

Not finding what you are looking for?
2003 Toyota Camry Logo

Related Topics:

473 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8826 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...