Question about 1996 Chrysler LHS

1 Answer

The traction control and abs warning lights comes on.

The warning lights come on in the message center when the car is first driven.However after the car is switched off then started again the lights go off but after the car is switched off for a few hours the problem returns.

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 56 Answers

Start the car for the first time, make sure the lights are doing it. Then push on the emergency brake a few times making sure it comes up all the way (if not help it out by hand). See if the lights stop. The ABS/Tracktion control is shut off when the E-brake is applied in Fords. I don't know if this is true in Chrysler's but is worth a check. If this has any effect on the lights then it's the pedal not coming all the way up or the switch in the E-brake mech coming loose or malfunctioning.

Posted on Feb 17, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Clearing/resetting ABS and Traction Control system warning lights - 2006 Buick Terraza

As long as your car's brakes work and is safe to drive, take it to any parts store. They have error code readers that can reset these alarms. If they are not able to reset them then you will probably have to take your car to a brake shop for maintenance on your ABS sensors. Traction control is associated with the ABS sensors.

Nov 09, 2017 | Buick Cars & Trucks

1 Answer

Electronic stability control & abs & brake assist warning indicator lights are coming on after an accident. How serious are they?

You have damage to the front area brake system. It could be very serious but if car stops OK most likely not that serious you just won't have abs or traction control. The damage is most likely a speed sensor or something similar. I said it could be serious that is only worst case.
Here is a breakdown of what lights mean
ABS keeps your breaks from locking up
BREAK ASSIST helps your breaks
Traction control if you one wheels spin more than others system adjust wheel spiN

Dec 19, 2015 | Cars & Trucks

1 Answer

Changed bearings and abs light and stabletrack still on do they reset after u replace the bearings and if so how long

Service Traction Control - Stabilitrak and ABS light, Help - Page ... > ... > Tahoe & Suburban
Aug 16, 2012 - Service Traction Control - Service Stabilitrak and ABS light came on. ... Its supposed to still be under warranty, "Major Guard". ... I replaced my rear shocks with OEM re-manufactured Arnott shocks (great company) and in the ... • Traction Control, Stabilitrak & ABS Issue
Jan 28, 2014 - Traction Control, Stabilitrak & ABS Issue. Tue Jan 28 ... The wife and I got in to head out and see my brother and as soon as I turned the key the ServiceTraction Control, Service Stabilitrak messages flashed and the ABS light came on. ... check your wheel bearings my was gone and caused the same thing ...

Chevrolet Impala Questions - Hello. I have a 2012 Chevy ... > Questions > Chevrolet > Impala

CarGurusApr 6, 2013 - Occasionally when I hit the brakes I get a Stabilitrak Error Message " ... I believe GM still had 3 year/ 36,000 mile bumper to bumper ... After about 2 months of intermittent noises the ABS light came on, the service stabilitrak warning, servicetraction ... Edit....left hub bearing change after the right one changed.

Replaced front hub - now ABS/Stabilitrak lights on... - Chevy ...

Dec 12, 2015 | Cars & Trucks

1 Answer

Traction control and abs warning light comes on,how do I fix??

the ABS system is defective, probably one or more of the sensors.

Traction control system works with the ABS sensors to monitor to monitor traction slippage.

Jul 20, 2014 | 2001 Chevrolet Impala

1 Answer

Light abs traction control stays 1998 buick park avenue

PRE-DIAGNOSTIC INSPECTIONBefore diagnosing ABS/TCS, perform a comprehensive visual inspection of system as follows.Check ABS/TCS wiring harness connectors for looseness. Check harness routing; pay particular attention to wheel speed sensor wiring harness routing. Check fuses No. 1D, 5B and 6B in instrument panel fuse block. Check fuses No. 1 and 2 in underhood fuse block. Check brake fluid level in master cylinder reservoir. Check brake fluid level in Pressure Modulator Valve (PMV) assembly reservoir. Ensure parking brake is fully released. Ensure parking brake switch is functioning properly. Always perform ABS/TCS system functional check before using DIAGNOSTIC CODE CHARTSThe EBCM/EBTCM has self-diagnostic capability, which can detect system failures. Fault codes stored by EBCM/EBTCM can be displayed using Tech 1 scan tester. There are no provisions for flash code diagnostics.Begin ABS/TCS diagnosis with PRE-DIAGNOSTIC INSPECTION procedure. If failures are found during pre-diagnostic inspection, perform necessary repairs, and proceed with ABS/TCS FUNCTIONAL CHECK. See Fig. 5 .If no failures are found during pre-diagnostic inspection, go to ABS/TCS FUNCTIONAL CHECK. See Fig. 5 . The ABS/TCS FUNCTIONAL CHECK will either indicate ABS/TCS is functioning properly or direct technician to various diagnostic procedures such as diagnostic charts, symptom diagnosis or BRAKE warning light diagnosis.CHART D - TRACTION OFF WARNING LIGHT ON CONTINUOUSLY & NO DTC SET (BUICK WITH UH8 OR U2A INSTRUMENT CLUSTER)Circuit DescriptionWhen ignition switch is first turned to RUN position, EBTCM goes through a self-test, which lasts 2-4 seconds. During self-test, EBTCM commands TRACTION OFF indicator warning light on. Powertrain Control Module (PCM) can also command EBTCM to set a Code 75 which will illuminate TRACTION OFF indicator.Traction control switch is located either on instrument panel center trim plate or driver's front door trim panel. Switch allows driver to select traction control mode (on/off). When traction control system is turned off, TRACTION OFF warning light comes on.EBTCM monitors transaxle temperature through

Jul 12, 2014 | 1998 Buick Park Avenue

1 Answer


TC = Traction Active

If your vehicle is equipped with the Traction Control system, this message will stay on a few seconds after the traction system stops limiting wheel spin.

This message will appear when the traction control system is limiting wheel spin. Keep in mind that when the warning lights turn on, a fault code is stored in the ABS control module (in this case). Retrieving, diagnosing, and repairing any ABS system faults will be necessary to keep the light off. A common fault with ABS systems are the wheel speed sensors, stored codes may confirm this.

Hope this helps.

Apr 13, 2011 | 2005 Chevrolet Impala

1 Answer

The ABS light comes on, and sure enough on slipery road conditions, there's no ABS. BUT when it's icy, the ABS light on the dashboard goes out, and checking to see if I have ABS, sure enough I do. It's...

the abs warning light also works with the electronic traction control, (or traction control,same system,different names) and when icy, stops the wheels from spinning,above about 15 mph.(the abs dont work under 5mph) so if im right regarding your question,your car is doing what its supposed to,stopping the driving wheels from spinning/locking up.the warning light comes on when one or the other is doing its job.(working).the trick is to drive so that the warning light doesnt come on..... boring.

Jan 28, 2011 | 2000 Volkswagen Beetle

1 Answer

I am getting random warning for traction control and abs.

hi hope i can help the traction control is controled by signals from the abs system if you lose a sensor imput the abs light will also come it looks like you have a sensor on the blink hope you find this helpful if so please give it a rating thanks pete

Nov 24, 2009 | 1999 Oldsmobile Intrigue

2 Answers

Abs light on accord 1992

ABS control unit recognizes system related problems and causes ABS warning light to come on and stay on under any of following conditions:
  • ABS pump runs longer than 2 minutes.
  • Vehicle is driven with parking brake on longer than 30 seconds.
  • One rear wheel is locked.
  • Wheel speed sensor does not transmit a signal.
  • Vehicle is driven on extremely rough road.
  • Low battery voltage.
  • Operation time of solenoid valves exceeds a specified value and control unit indicates an open circuit in solenoid circuit.
  • Output signals from control unit are not transmitted to solenoid valves.
  • Temporary loss of traction due to excessive cornering speed or starting from stuck condition (mud, snow or sand).

Nov 19, 2009 | 1992 Honda Accord

5 Answers

Traction Control Off and Service ABS System

If your trac and abs are both on. the problem could be a wheel speed sensor.
on some GM cars this sensor is built into the vehichles hub unit. making the bering and sensor one sealed unit. cheap hub units can be gotten (under 100 bucks) at autozone

Jul 21, 2009 | 2004 Pontiac Grand Prix

Not finding what you are looking for?
1996 Chrysler LHS Logo

308 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides