Question about 1995 Buick Park Avenue

1 Answer

Power steering pump

The two bolts that attachs the power steering pump to the alumnium engine is cracked the other bolt has broken off inside of the female end. is there some type of material/compuond i could use to create a new area to drill a hole so i could possibly reattach the pump?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 100 Answers

The best thing you can do is redrill and tap oversize bols into the block

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace power steering pump on 1998 Volvo v70


Place the vehicle in park or neutral with the emergency brake. Let the engine idle. Raise the hood and remove the cap on the power steering pump reservoir. The cap will have a plastic dipstick on the end of it. Wipe the dipstick portion with a rag and screw it back down on the reservoir. Unscrew the lid and check the level indicated on a marked scale on the dipstick. The level should read at the top "Hot" mark. Low fluid level will cause the pump to whine. Fill to the appropriate level and listen for noise.
Inspect the condition of the power steering fluid with the cap off the reservoir. It should be translucent red and slightly thick to the touch. Brown, black or sudsy-looking fluid indicates contamination. Power steering fluid that has lost its viscosity (thickness) cannot properly lubricate the seals, bearings and vanes inside the pump, which will cause a high-pitched whine or squealing noise. If the fluid feels gritty between the fingers, it means rust, metal shavings and dirt has entered the reservoir.
Use a slot screwdriver to loosen the low-pressure rubber hose clamp on the bottom side of the power steering pump reservoir. Catch any drippings in a pan. Loosen the high-pressure metallic line nut on the power steering pump body with a fuel line wrench. Let the fluid drain into a pan. Remove the reservoir cap and use a used turkey baster to suck out all of the power steering fluid. Clean the inside of the reservoir with a rag wrapped around a screwdriver.
Reconnect the rubber low-pressure side hose and tighten the clamp with a slot screwdriver. Screw the metallic line nut on by hand and finish tightening it with a fuel line wrench. Fill the reservoir with new (manufacturer's recommended) power steering fluid to the top mark. Start the engine and listen for noise.
Test the tension and condition of the serpentine belt, or the individual power steering belt. The belt should not be cracked or contaminated with oil or power steering fluid. Clean the belt with alcohol. Adjust the (individual) belt for tension, using an end wrench to loosen the adjusting bolt, and a socket and wrench to slightly loosen the pump mounting bolts. Pry the pump outward with a screwdriver to tighten the slack in the belt. Tighten the adjusting bolt with an end wrench. Tighten the mounting bolts with a socket and wrench.
Autel MaxiDAS DS708

Sep 25, 2014 | Volvo V70 Cars & Trucks

1 Answer

Diagram of 1999 Cavalier power steering pump


Chevrolet Cavaliers have power steering installed as standard equipment. The power steering is assisted with hydraulic pressure generated by the power steering pump. The pump circulates the fluid and makes turning the steering wheel very light and responsive to the touch. A sure sign the power steering pump is failing is when steering becomes more laborious; also look for leaking power steering fluid puddled under the car. Removing a power steering pump is not a difficult project and is the first step to repairing the power steering system.
Related Searches:

  1. Serpentine Belt
    • The serpentine belt on the front of the Cavalier's engine provides the power to operate the power steering pump. You have to first remove the belt to free the power steering pump's drive pulley. Underneath the Cavalier is a spring-tensioned pulley keeping the serpentine belt taut. Use a socket wrench to grab the center hex nut on the tension pulley and turn it so the belt becomes loose. Remove the belt from the pulley and then from the other wheels and pulleys on the engine.

    Tubing
    • A tube runs from the pump to the power steering assist mechanism in the Cavalier near the front axle. This hard tube has two fittings on each end for a connection. Use a box-end wrench to disconnect one end of the tube underneath the Cavalier. Be careful because some power steering fluid will leak. Just hold your finger over the hole and set a container underneath the tube and wait for the fluid to drain.

      Once the fluid finishes draining use the box-end wrench to disconnect the tube from the power steering pump. The tube is bent and twists to make its way through the engine bay from the pump to the power steering assist. There's no need to remove it from the bay. Just push it aside.

    Pump
    • The power steering pump is bolted directly onto the engine block. To remove the pump, unscrew the fasteners securing it to the engine. There may or may not be thread lock compound used to seal the bolts onto the engine. If the bolts do not easily turn use some force to break the thread lock. Do not worry about doing this. Breaking thread lock is the only way to get a bolt free. Once the bolts are out, lift the pump out of the engine bay. Again, though, be careful because as you move the pump some remaining power steering fluid may drain from the access port where the tubing was connected. You might want to get a shop towel to hold over the port when moving the pump to avoid a dripping mess.

Jan 12, 2012 | Chevrolet Cavalier Cars & Trucks

1 Answer

Need R&R information to replace for waterpump Geo Storm 1993 4 cyl


Hi!!
Here is the Info you requested:
WATER PUMP REMOVAL & INSTALLATION
Except Twincam Engines See Figures 1 and 2
  • Disconnect the negative battery cable and drain the cooling system.
  • Loosen the power steering pump adjustment bolts and remove the drive belt.
  • Remove the timing belt; refer to the procedure later in this section.
  • Remove the tension pulley and spring.
  • Remove the water pump mounting bolts, water pump and gasket. Clean the mounting surfaces of all remaining gasket material.
  • To install, reverse the removal procedures. Tighten the water pump bolts to 17 ft. lbs. (23 Nm) and the tension pulley to 30 ft. lbs. (40 Nm).
  • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks.

FIG 1 1kbron_114.jpg
FIG 2 1kbron_115.jpg

Twincam Engines See Figure 3
1.6L DOHC ENGINE
  • Disconnect the negative battery cable and drain the cooling system.
  • Support the engine using a suitable floor jack and remove the right front engine mount.
  • Remove the engine mount bridge and the upper timing belt cover.
  • Remove the power steering belt and the lower timing belt cover.
  • Loosen the timing belt tension pulley and remove the timing belt.
  • Remove the power steering pump and bracket.
  • Remove the water pump attaching bolts, then the water pump from the vehicle. Thoroughly clean all remaining gasket material from the mating surfaces.
  • Reverse procedure to install and tighten the water pump bolts to 17 ft. lbs. (24 Nm). Connect the negative battery cable and refill the cooling system. Start the engine and check for leaks.
FIG 3 1kbron_116.jpg
1.8L ENGINE
  • Disconnect the negative battery cable and drain the engine cooling system.
  • Remove the timing belt covers; refer to the procedure later in this section. Loosen the timing belt tensioner pulley bolt, then remove the belt from the water pump pulley.
  • Remove the 2 bolts from the power steering pump bracket, then position the pump aside with the lines still attached. Be careful not to kink or damage the steering fluid lines.
  • Remove the water pump mounting bolts, then remove the pump from the engine. Thoroughly clean the gasket mating surfaces of all remaining gasket material.

To install:
  • Install the water pump using a new gasket, then tighten the retaining bolts to 18 ft. lbs. (24 Nm).
  • Position the power steering pump assembly, then install the retaining bolts and tighten to 25 ft. lbs. (34 Nm).
  • Install the timing belt to the pump pulley, then tighten the tensioner pulley bolt to 30 ft. lbs. (40 Nm).
  • Install the timing belt covers.
  • Connect the negative battery cable and fill the cooling system, then start the engine and check for leaks
Good Luck!! A HELPFUL - 4 THUMBS - rating for this solution would be greatly appreciated. Thank you for using FixYa.

Mar 11, 2011 | Geo Storm Cars & Trucks

1 Answer

Power steering pump change how to?


3.1L and 3.4L (VIN E) Engines


0900c15280217fc8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Power steering pump mounting-3.1L and 3.4L (VIN E) engines

  1. Disconnect the negative battery cable.
  2. Remove the coolant recovery reservoir and position it aside.
  3. Remove the serpentine drive belt from the power steering pump assembly.
  4. Detach the ignition control wiring harness near the pump assembly.
  5. Disconnect the inlet and outlet hoses from the pump assembly.
  6. Unfasten the pump retaining bolts/screws.
  7. Remove the pump assembly from the vehicle.
  8. Remove the power steering pump pulley from the pump assembly.
  9. Remove the reservoir assembly from the pump.

To install:
  1. Attach the reservoir to the pump assembly.
  2. Install the pulley to the pump.
  3. Position the pump to the engine and secure with the retaining bolts/screws. Tighten the bolts/screws to 25 ft. lbs. (34 Nm).
  4. Connect the inlet and outlet hoses to the power steering pump.
  5. Attach the ignition control wiring harness at the pump assembly.
  6. Install the serpentine drive belt over the power steering pump pulley.
  7. Install the coolant recovery reservoir.
  8. Connect the negative battery cable.
  9. Fill and bleed the power steering system.

Feb 09, 2011 | 1999 Oldsmobile Intrigue

1 Answer

Repair power steering for 1994 Chevy S10 Blazer V-6, pump and houses.


Power Steering Pump Removal & Installation 2.2L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Position a fluid catch pan under the power steering pump.
  3. Disconnect the feed and return hoses from the power steering pump, then drain the excess fluid into the catch pan. NOTE: On models equipped with a remote fluid reservoir, disconnect and plug the hose(s) in order to prevent system contamination or excessive fluid loss.
  4. Remove the drive belt from the pulley.
  5. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump. NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
    Installing the pilot bolt 85388111.gif

    Removing the power steering pump pulley 85388113.gif

    Installing the power steering pump pulley 85388114.gif

  6. Unplug the electrical connection from the A/C compressor, unfasten the compressor mounting bolts and set the compressor to one side without disconnecting the lines.
  7. Remove the front mounting bolts and the rear bracket nuts from the studs on the engine.
  8. Remove the rear brace mounting bolt.
  9. Remove the power steering pump from the vehicle.
To Install:
  1. Position the pump to the vehicle and secure using the front retaining bolts to 22 ft. lbs. (30 Nm).
  2. Install the rear bracket bolt and nuts. Tighten the retainers to 22 ft. lbs. (30 Nm) on 1994 - 97 models and 37 ft. lbs. (50 Nm) on 1998 and later models.
  3. Install the A/C compressor.
  4. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  5. Properly install the drive belt.
  6. Remove the caps, then connect the feed and return hoses to the pump.
  7. Properly refill and bleed the power steering system.
  8. Test drive the vehicle.
4.3L Engine To Remove:
  1. Remove the upper cooling fan shroud.
  2. Remove the drive belt.
  3. Remove the fan and clutch from the water pump.
  4. Install a puller tool such as J-25034, or equivalent onto the power steering pump pulley. While holding the pilot bolt, turn the tool nut counterclockwise in order to press the drive pulley from the pump.
  5. Safely raise and support the vehicle.
  6. Remove the shield from the steering linkage.
  7. Position a fluid catch pan under the power steering pump.
  8. Disconnect the return hose from the power steering pump, then drain the excess fluid into the catch pan.
  9. Safely lower the vehicle.
  10. Disconnect the pressure hose from the pump and cap the open line.
  11. Remove the filler neck tube.
  12. Remove the power steering pump mounting nuts and bolts.
  13. Remove the power steering pump from the vehicle.
NOTE: When installing the puller tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
Installing the pilot bolt 85388111.gif

Removing the power steering pump pulley 85388113.gif

Installing the power steering pump pulley 85388114.gif

To Install:
  1. Position the pump to the vehicle.
    • Tighten the front retaining bolts to 37 ft. lbs. (50 Nm) and the nuts to 31 ft. lbs. (41 Nm).
  2. Install the filler neck tube.
    • Tighten the bolt to 15 ft. lbs. (20 Nm).
  3. Connect the pressure hose to the pump.
  4. Safely raise and support the vehicle.
  5. Connect the return hose to the vehicle.
  6. Install the shield on the steering linkage and lower the vehicle.
  7. Use a pulley installer such as J-25033 or equivalent to press the drive pulley onto the power steering pump. While holding the pilot bolt, turn the tool nut clockwise in order to press the drive pulley onto the pump. Check that the pulley is flush within 0.010 in. (0.25mm) of the shaft end. NOTE: When positioning the installer tool onto the power steering pump pulley, be sure that the pilot bolt bottoms in the pump shaft by turning the head of the pilot bolt.
  8. Install the fan and clutch on the water pump.
  9. Properly install the drive belt. NOTE: Be sure to secure any hoses which may get in the way or rub other components.
  10. Install the upper fan shroud.
  11. Properly refill and bleed the power steering system.
  12. Test drive the vehicle.
prev.gif next.gif

Nov 05, 2010 | Chevrolet S 10 Cars & Trucks

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

1 Answer

How to install a power steering pump for a 1997 chrysler seabring conv


Chrysler Cirrus/Stratus/Sebring/Avenger/Breeze 1995-1998
Power Steering Pump - REMOVAL & INSTALLATION

Cirrus, Stratus, Sebring Convertible and Breeze
(see Figures 1, 2, 3 and 4)
  1. Disconnect the negative battery cable from the left strut tower. The ground cable is equipped with an insulator grommet, which should be placed on the stud to prevent the negative battery cable from accidentally grounding.
  2. Siphon as much power steering fluid out of the reservoir as possible.
  3. Raise and safely support the vehicle.
  4. Remove the right front tire and wheel assembly.
  5. Remove the splash shield from the right front wheel well.
c901554.jpg

Fig. 1: Power steering pressure hose attachment to the pump-with Variable-Assist steering

8786c07.jpg

Fig. 2: Power steering pressure hose attachment to the pump-without Variable-Assist steering
  1. Disconnect the power steering pressure hose from the pump.
  2. Remove the hose connection on the power steering pump.
e7733b2.jpg

Fig. 3: Typical power steering pump front bracket attachment
  1. Remove the power steering adjusting bolt.
  2. Remove the power steering pump rear attaching bolt.
  3. If so equipped, remove the Anti-lock Brake System (ABS) hydraulic control unit heat shield.
  4. Remove the wheel speed sensor retainer bracket from the right inner fender.
  5. Remove the wheel speed sensor sealing grommet from the right inner fender.
  6. Disconnect the speed sensor wiring.
  7. Push the wiring through the hole in the inner fender.
If not equipped with anti-lock brakes, the hole will just have a sealing plug.
  1. Remove the bolt attaching the power steering front bracket to the mounting bracket. Access to the bolt is gained through the hole for the speed sensor wiring.
  2. Remove the power steering pump drive belt.
  3. Remove the power steering pump and the front bracket as an assembly.
To install:
  1. Install the power steering pump and bracket.
  2. Reinstall the bolt at the adjusting slot, but do not tighten.
  3. Reinstall the bolt mounting the power steering pump to the rear mounting bracket, but do not tighten.
  4. Reinstall the power steering pump top bolt, but do not tighten.
  5. Reconnect the power steering hoses.
b72b14a.jpg

Fig. 4: Install a new O-ring gasket on the hose fitting
Use a new O-ring when reinstalling the power steering pressure hose.
  1. Reinstall the drive belt.
  2. Adjust the drive belt and tighten the power steering pump bolts to 40 ft. lbs. (54 Nm).
  3. Reinstall the splash shield.
  4. Reinstall the tire and wheel assembly.
  5. Lower the vehicle.
  6. Reconnect the negative battery cable.
  7. Refill the reservoir and bleed the power steering system.


Sebring Coupe and Avenger
  1. Disconnect the negative battery cable.
  2. Remove (drain, suction pump, etc.) as much power steering fluid as possible.
  3. Disconnect the return fluid line. Remove the reservoir cap and allow the return line to drain the fluid from the reservoir. If the fluid is contaminated, disconnect the ignition high tension cable and crank the engine several times to drain the fluid from the gearbox.
Cover any components located underneath the power steering pump with a shop towel to protect them from damage due to power steering fluid spillage. For example, the A/C compressor or alternator, depending on vehicle and engine, is below the power steering pump, so cover the A/C compressor or alternator with a shop towel before removing any hoses.
  1. Loosen (but do not remove) the power steering pump mounting bolts and remove the drive belt.
  2. Remove the pressure switch connector from the side of the pump.
  3. Disconnect the pressure line.
  4. Unbolt and remove the pump from the mounting bracket.
To install:
  1. Clean all parts well. Inspect the pump pulley for cracks. Check the hoses carefully for cracks or signs of weakness.
  2. Install the pump, wrap the belt around the pulley and lightly tighten the mounting bolts.
  3. Replace the O-rings and connect the pressure line. Connect the pressure line so the notch in the fitting aligns and contacts the pump's guide bracket. Tighten the fitting to 13 ft. lbs. (18 Nm).
  4. Connect the return line and secure with the clamp.
  5. Fasten the pressure switch connector.
  6. Adjust the power steering belt for proper tension and tighten the adjusting bolts.
Use only MOPAR ATF PLUS automatic transmission fluid type 7176, ATF+3 automatic transmission fluid, or equivalent, in the power steering system of Sebring coupe and Avenger models.
  1. Refill the reservoir and bleed the power steering system.

Hope this help to solve it (remember comment and rated this). TY for using Fixya.

May 13, 2010 | 1997 Chrysler Sebring

1 Answer

Removal and installation of the water pump


3.0L or 3.8L engine?

please rate as fixed if this solves your issue.

Section 03-01B: Engine, 3.8L 1996 Windstar Workshop Manual
IN-VEHICLE SERVICE Water Pump SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
  1. Drain engine cooling system. Refer to Section 03-03 .
  1. Loosen drive belt tensioner (6B209) and remove drive belt (8620). Refer to Section 03-05 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Disconnect lower radiator hose (8286) from radiator lower hose tube (8291) and radiator (8005).
  1. Disconnect radiator lower hose tube from water pump (8501).
  1. Remove lower nut on both front engine support insulators (6038).
  1. Lower vehicle.
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove generator (GEN) (10346) from power steering pump support (3C511).
  1. Position drain pan and disconnect power steering pressure line from power steering pump (3A674) using Fuel Line Disconnect Tool Set T90T-9550-S.
  1. Remove power steering reservoir filler cap.
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: If using a prying device to assist in water pump removal, be careful not to damage the mating surfaces.
    Disconnect water bypass hose (8597) and oil cooler hose (6B850) from heater water outlet tube (18663).
  1. Remove retaining bolts and disconnect heater water outlet tube from water pump.
  1. Remove A/C bracket brace.
  1. Attach engine lifting eye to left-hand (front) exhaust manifold (9430).
  1. Attach lifting equipment to engine lifting eye and raise front of engine approximately 51 mm (2.0 inches) to provide necessary clearance for water pump removal.
  1. Remove water pump pulley retaining bolts and water pump pulley (8509).
  1. Remove drive belt tensioner pulley retaining bolt and drive belt tensioner pulley (6B217) from power steering pump support.
  1. Remove power steering pump support retaining bolts and nut. Place power steering pump and support assembly aside in a position to prevent fluid leakage.
  1. Remove water pump retaining bolts and nuts and water pump. Discard used water pump housing gasket (8507).
Installation
  1. NOTE: Lightly oil all bolt and stud bolt threads before installation except those specifying special sealant.

    Clean gasket surfaces on water pump and engine front cover (6019).
  1. NOTE: The threads of the No. 1 engine front cover retaining stud must be coated with Pipe Sealant with Teflon® D8AZ-19554-A or equivalent meeting Ford specification WSK-M2G350-A2 before installing.

    NOTE: Gasket and Trim Adhesive D7AZ-19B508-B or equivalent meeting Ford specification ESE-M2G52-A is recommended to hold the water pump housing gasket in position.

    Position a new water pump housing gasket on water pump housing sealing surface.
  1. Position water pump on the engine front cover. Install retaining bolts.
  1. Position power steering pump support and install retaining nuts and bolts. Tighten bolts and nuts to 40-55 Nm (30-40 lb-ft).
  1. Install drive belt tensioner pulley and retaining bolt. Tighten bolt to 70-95 Nm (52-70 lb-ft).
  1. Install A/C bracket brace.
  1. Position water pump pulley on water pump hub and install retaining bolts. Tighten bolts to 8.0-11.5 Nm (71-101 lb-in).
  1. Lower engine and disconnect lifting equipment from lifting eye.
  1. Remove lifting eye from exhaust manifold.
  1. Connect heater water outlet tube to water pump and install retaining bolts. Tighten bolts to 8-11.5 Nm (71-101 lb-in).
  1. Connect water bypass hose and oil cooler hose to heater water outlet tube. Tighten clamps securely.
  1. Connect power steering pressure line to power steering pump fitting.
  1. Install power steering reservoir filler cap.
  1. Install generator to power steering pump support. Refer to Section 14-02 .
  1. Connect battery ground cable. Refer to Section 14-01 .
  1. Raise vehicle on hoist. Refer to Section 00-02 .
  1. Install lower nut on front engine support insulators and tighten retaining nut to 88-119 Nm (65-87 lb-ft). Install lower nut of rear engine support insulator and tighten to 77-104 Nm (56-76 lb-ft).
  1. Connect radiator lower hose tube to water pump. Install retaining bolt and tighten securely.
  1. Connect lower radiator hose to radiator lower hose tube and radiator. Position hose clamps securely. Refer to Section 03-03 .
  1. Lower vehicle.
  1. Position drive belt over drive belt tensioner and release drive belt tensioner. Refer to Section 03-05 .
  1. stw~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: This engine has aluminum cylinder heads (6049) and requires a special corrosion inhibiting coolant to avoid cooling system damage. Refer to Section 03-03 for the coolant specifications.
    Fill and bleed cooling system with specified coolant.
  1. Fill power steering pump reservoir with specified fluid.
  1. Start engine and check for coolant and power steering fluid leaks. Service as necessary.


    Water Pump
581f50d.gif

Apr 13, 2009 | 1996 Ford Windstar

1 Answer

95 buick park ave power steering pump bolts


I think any dealer would have these on hand; if my memory is working right, these did have to be a specific class and will need to be torqued carefully to avoid stripping the female threads.  

Feb 16, 2009 | 1995 Buick Park Avenue

1 Answer

Inatallation 92 honda accord power steering pump


Hey, here's the procedure, disable air bag, if equipped w/ one, disconnect the pump return hose from the reservoir and place the end in a large container. Plug the port in the reservoir. Start the engine and turn the steering wheel lock to lock several times, until fluid stops running from the hose. Turn off engine immediately. Re-attach hose. Disconnect the inlet and outlet hoses at the pump. Remove the drive belt. Remove the mounting bolts/nuts and remove pump.
Install in reverse order. Adjust belt tension,fill ps reservoir and bleed any air from the system (to bleed air from system, fill reservoir, start engine and allow to idle, turn wheel from side to side all the way several times. Shut off, fill if necessary.
. Tighten bolts to : Thru bolt 30 ft lbs., mounting nut 16 ft lbs.

Dec 26, 2008 | 1992 Honda Accord

Not finding what you are looking for?
1995 Buick Park Avenue Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...