Question about 1995 Oldsmobile Silhouette

1 Answer

'95 Sihlouette front directional bulb replacement

How do I replace the front directional bulb? I see no screws to remove the lens cover from the exterior.

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

From the inside of the engine compartment. Sometimes the entire lens holder has to be removed in certain cars. But see if your car has a plastic holder of the bulb where you can turn it counter clockwise to remove .You turn it a little bit then pull it out.

Posted on Feb 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can't remove lens cover on rear to access burned out bulb. Screws are out but don't want to crack the cover.

it may be possible that you don't have to remove the lens cover to replace the bulb, in most modern vehicles the bulbs come out from inside the trunk by turning the fitting & pulling the bulb out & replace it the same way by putting it back in & turning it in the opposite direction to lock it in place.......hope this helps......cheers.

Sep 04, 2011 | 2002 Mazda Tribute

1 Answer

Drivers side headlight bulb replacement

  1. Open the hood to the 1999 Dodge Stratus.

  2. Locate the two headlight lens assembly retaining screws at the top of each side of the assembly.
  3. Remove each screw with the ratchet and a suitable socket.
  4. Place the screwdriver behind the lens assembly to assist in prying out the guide pins that secure and align the headlight assembly. Hold the lens assembly from the outside edge (marker light/directional light section) first and pry from behind with the screwdriver to unseat the guide pins. Pry from the inside end of the lens assembly to unseat the other guide pin.
  5. Pull the lens assembly out far enough to reach behind it and disconnect the headlight bulb wire harness from the back of the bulb. Or simply remove the bulb by twisting the harness and retaining ring counterclockwise and remove it as an assembly.
  6. Turn the marker light/directional light socket and wire counterclockwise to remove it from the headlight lens assembly.
  7. Remove the assembly from the front of the Stratus.

Feb 28, 2011 | 1999 Dodge Stratus

1 Answer

How do you change headlamp/bulb

Hello there, hope these guidelines are of help.
  • Open the hood and and take out the eight fastener plugs that connect the radiator cover to the front of the vehicle. Grasp the plugs from underneath, and squeeze them as you push them up and out of the hole. You do not need to remove the cover, but you need to be able to pull it away from the vehicle slightly to be able to remove the headlight.
  • Grasp the radiator cover close to the lens of the headlight you need to replace, and gently pull it up and toward you to access the headlight screws.
  • Remove the three headlight screws using a socket wrench. There are two screws directly below the lens, and one screw on the side of the lens closest to the outer edge of the vehicle.
  • Pull the edge of the radiator cover away from the vehicle, and lift the headlight assembly up and out of its frame.
  • Press the clip on the electrical connector to release it, and pull the connector out of the bulb retainer. Turn the bulb retainer counterclockwise 1/4 turn and pull it out of the assembly.
  • Pull the bulb out of the socket and insert the new bulb. Do not touch the bulb's glass with your fingers. Use a clean, lint-free cloth to handle the bulb if necessary.
  • Insert the bulb and retainer into the assembly, and turn it 1/4 turn clockwise to secure it. Plug the electrical connector into the bulb retainer.
  • Place the headlight back into its frame and replace the screws. Put the radiator cover back into place and insert the eight fastener plugs.
Best regards...

Jan 22, 2011 | 2005 Chevrolet Equinox

1 Answer

I need to replace the bulb on my 95 rodeo front blinker. It has a couple of screws, but I took them out and for the life of me I can't get the lens cover off?

The len's is a sealed unit you need to remove the light. The light is held in with the screws you have taken out but also has a plastic round holder on the back which connects it to the pannel (wheel arch) . To remove the light pull it straight out from the front. Sometimes they can not be removed by hand so you may need to pry it slightly with a screwdriver between the lens and the wheel arch. Be carefull not to damage the paint.

Jan 14, 2010 | 1995 Isuzu Rodeo

1 Answer

2000 sunbird front turn signal bulb

only i could replace mine where to remove clips from the black wheel well cover then the light bulb un screws from the back of the lens

Apr 07, 2009 | 2000 Pontiac Sunfire

2 Answers

'95 Olds Silhouette Front Directional bulb replacement

you suld be able to just turn the bracket the bulb sits in and get to it that way...thereare no screws to take out.

Feb 16, 2009 | 1995 Oldsmobile Silhouette

1 Answer

Replace front turn signal bulb

remove top screw and pull cover straight out to access bulb

Jul 27, 2008 | 1992 Toyota Land Cruiser

1 Answer

How to access front turn signal for replacement

Here you go, removal & installation of:

Front Parking/Turn Signal Lights:
  • Remove the screws from the the lens and separate the lens from the bezel
  • Remove the screws from the turn signal housing and pull it out
  • Turn the bulb socket CCW 1/3 turn and remove it
  • Installation is the reverse of this procedure
Side (Front) Marker Lights:
  • Remove the screws from the marker lens
  • Separate the lens from the headlight
  • Pull the bulb from the back of the lens
  • Installation is the reverse of this procedure
Hope this helps


Jul 06, 2008 | 1995 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Oldsmobile Silhouette Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts


Level 3 Expert

77201 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8743 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides