Question about 1983 Peugeot 604

1 Answer

Will the piston in a 505 2.2 88 gas wagon fit 85 turbogas 505 sdn

It' hard to find spec and information about this car. The wagon is a puegeot 1988 505 2.2i gt. I have a hard to work on 1985 505 turgogas engine. Trying to rebuild engine to restore car. Side note where in the US can one order parts?


Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Peugeot Master
  • 6,982 Answers

You may need to order a set...You need to know exact re-finished bore size, compression ratio, ring placement, ring land dimensions and wristpin location. As far as parts, there are likely clubs for your vehicle that can help you out with that. (I used to have to get up really early to order parts for an old rover 2000tc I had a few years back... Only place to get anything was in England!!!) I hope your stuff is easier to get!!!

Posted on Feb 16, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Fuel Rail Leak

Did did you change the o-ring at the fuel line to fuel rail connector? Do that before you change the fuel rail. According to an e-bay seller who is selling a used fuel rail from his salvage shop, the following fuel rails are interchangeable.
300 05-10 Fuel Injector; 2.7L and 3.5L
AVENGER 08-10 Fuel Injector; 2.7L
AVENGER 08-10 Fuel Injector; 3.5L
CARAVAN 08-10 Fuel Injector; 4.0L
CHALLENGER 09-10 Fuel Injector; 3.5L
CHARGER 06-10 Fuel Injector; 2.7L and 3.5L
JOURNEY 09-10 Fuel Injector; 2.7L
JOURNEY 09-10 Fuel Injector; 3.5L
MAGNUM 05-08 Fuel Injector; 2.7L and 3.5L
NITRO 07-11 Fuel Injector; 4.0L
PACIFICA 05-06 Fuel Injector; 3.5L
PACIFICA 07-08 Fuel Injector; 4.0L
SEBRING 04 Fuel Injector; Conv, 2.7L, from 07/30/03
SEBRING 04 Fuel Injector; Sdn, 2.7L, from 07/30/03
SEBRING 05 Fuel Injector; Conv, 2.7L
SEBRING 05 Fuel Injector; Sdn, 2.7L
SEBRING 06 Fuel Injector; (Conv, Sdn), 2.7L
SEBRING 07 Fuel Injector; (Sdn), 2.7L
SEBRING 07 Fuel Injector; (Sdn), 3.5L
SEBRING 08-10 Fuel Injector; (Conv, Sdn), 2.7L
SEBRING 08-10 Fuel Injector; (Conv, Sdn), 3.5L
STRATUS 04 Fuel Injector; Sdn, 2.7L, from 07/30/03
STRATUS 05 Fuel Injector; Sdn, 2.7L
STRATUS 06 Fuel Injector; (Sdn), 2.7L
TOWN & COUNTRY 08-10 Fuel Injector; 4.0L

Mar 04, 2014 | 2007 Chrysler Pacifica Touring

2 Answers

Engine torque settings mitsubishi 4d32

im looking for information by a 4d32 Mitsubishi , help!!!!!! thanks

Apr 03, 2012 | 1988 Mitsubishi Cargo

1 Answer

1988 subaru wagon with carby no turbo.Which one is #1 cylinder, and what is the correct top dead centre angle for timing

Number one is the forward most piston on the car, when the piston is at tdc, it will have a timing mark up front on the pulley pointing to an arrow, Or the valves will be at rest on number one, if you have the rocker covers off. If it has a distributor, the points will be pointing at number one plug wire. But the timing mark is what you are looking for anyway. Check it out, hope this helps.

Aug 29, 2010 | 1988 Subaru GL-10

1 Answer

Where is the vacuum pump on a 1988 celebrity wagon?

Unless it has a diesel engine, don['t remember there ever being one on there. If you are looking for an air pump (has nothing to do with vacuum) likely on one that old, it seized and was removed a long time ago.
On a gas engine, the engine itself makes the vacuum which is then routed from the intake or carb fittings to where it is needed.

Aug 07, 2010 | 1988 Chevrolet Celebrity

1 Answer

When the car gets to operating temp. it losses spark except when you turn the key on it sparks 1 time and i have replaced the iginition control box

My '85 wagon did the same thing. I replaced a small but expensive module inside the distributor and everything worked fine. It was about a hundred bucks for the module ten years ago.

Feb 09, 2010 | 1988 Subaru Justy

1 Answer

I have 4.9L6 need torque specs for cylinder head

for cylinder head the torque is : step 1 55 ft-lb, step 2 65 ft-lb, step 3 85 ft-lb. Rocker arm stud nut or bolt is 17 to 23 ft-lb. and valve cover bolt 72 to 108 in-lb.


Dec 05, 2009 | 1988 Ford F 150

1 Answer

What size tires do i need??

From BFGoodrich Tires:
- 1989 Oldsmobile Cutlass Ciera International Series
Original Equipment: P215/60R14

- 1989 Oldsmobile Cutlass Ciera Wagon
Original Equipment: P185/75R14
Alternate Option: P195/70R14

The information disponible for 1988 model is hard to find. I hope that this can help you.

Nov 26, 2009 | 1987 Oldsmobile Ciera

2 Answers

I have Toyota Camry 1988 wagon and need instruction

On this old of a model there is no way to depressurize the system without breaking open a fitting. The easiest way to do this is to lightly crack open the fittings at the fuel filter and let the pressure bleed off into a jug. After the pressure is released you can safely unscrew, remove, replace and put back together. Do keep in mind once the new filter is installed the engine may crank immediately then die and it may require several moments of cranking to start due to the excess air in the system. Hope this helps, good luck!

Sep 02, 2009 | 1988 Toyota Camry

1 Answer

1988 jetta front psnger door won't open

you have to remove door panel ,you can gain access to it with the rindow up,the link from the handle to the latch has staightened slightly . it will need bending to get shorter

Aug 07, 2009 | 1988 Volkswagen Jetta

1 Answer


The ground has corroded off the sending unit.You can access this by drilling out the rivits in the access panel under rear seat on drivers side.

Sep 30, 2008 | 1988 Jeep Grand Wagoneer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides